Spacers on stock Z?

semtex · 03-08-2009, 05:07 PM

I did a little looking around on Google and found this: Wheel Stud Remover SA91107NE

dlmartin81 · 03-08-2009, 06:02 PM

^^ hmmm good find.

Minicobra1 · 03-09-2009, 05:54 AM

Quote:

Originally Posted by semtex

I did a little looking around on Google and found this: Wheel Stud Remover SA91107NE

Yeah, that's it

A little pricey though, I was hoping it would be around $50-$60 bucks. Much better then using a hammer.

alan93rsa · 03-09-2009, 10:36 PM

The price isn't too bad if you add in the cost of damaging a hub or bearing beating a stud out. If two people went in on one the price would be half. Just need to find a local or be willing to ship it to the second person.

There are a few tools which circulate on the NSX board which are not ones you would would want to own. I used the ABS bleeder for my NSX. You put your name on the list and the members just keep forwarding the tool. Not a bad deal until someone gets the tool and runs into issues getting their job done.

semtex · 03-10-2009, 07:48 AM

^ I was kinda tossing the same idea around in my head. We could start a 'tool co-op'.

SiXK · 03-10-2009, 10:28 AM

Quote:

Originally Posted by semtex

^ I was kinda tossing the same idea around in my head. We could start a 'tool co-op'.

hmmm... not a bad idea.... I would be interested in going in on this tool.

VIP-STATUS · 03-18-2009, 11:14 PM

I say 15mm front+rear will be perfect

Minicobra1 · 04-05-2009, 12:01 PM

Anyone know of a So-Cal shop that would do the install on the spacers?
Someone that has the proper stud press tool and not a hammer.

monthtrial · 04-06-2009, 01:21 AM

Quote:

Originally Posted by Minicobra1

Anyone know of a So-Cal shop that would do the install on the spacers?
Someone that has the proper stud press tool and not a hammer.

I'll check w/ my buddy who has a shop (local to you) to see if he uses tools rather than brute force for this kinda job.

Minicobra1 · 04-06-2009, 03:25 AM

Quote:

Originally Posted by monthtrial

I'll check w/ my buddy who has a shop (local to you) to see if he uses tools rather than brute force for this kinda job.

Thanks

i'm in the Brea area. Probably want to go with the H&R Spacers.

monthtrial · 04-07-2009, 12:00 AM

Quote:

Originally Posted by Minicobra1

Anyone know of a So-Cal shop that would do the install on the spacers?
Someone that has the proper stud press tool and not a hammer.

Cobra,

My buddy also gets rough w/ it; he uses a hammer and forces the studs out. He said he's performed 50+ stud jobs and has never encounted issues. He does have a tool (more like a machine) that he uses but the labor costs render it too costly; he takes off the whole break assembly. He doesn't use anything like the e-bay tool mentioned above.

Minicobra1 · 04-07-2009, 04:16 AM

Quote:

Originally Posted by monthtrial

Cobra,

My buddy also gets rough w/ it; he uses a hammer and forces the studs out. He said he's performed 50+ stud jobs and has never encounted issues. He does have a tool (more like a machine) that he uses but the labor costs render it too costly; he takes off the whole break assembly. He doesn't use anything like the e-bay tool mentioned above.

Hmmmm. Ok, well, why don't you PM me his info, I may just give him a call.

Thanks

Braden

Minicobra1 · 04-11-2009, 03:49 AM

Quote:

Originally Posted by VIP-STATUS

I say 15mm front+rear will be perfect

15mm spacer installed

semtex · 04-11-2009, 09:02 AM

Quote:

Originally Posted by Minicobra1

15mm spacer installed

That looks good, man!

Are you only doing the rear?

Minicobra1 · 04-11-2009, 12:59 PM

Quote:

Originally Posted by semtex

That looks good, man!

Are you only doing the rear?

No, I'm installing some Eibach springs today, wanted to check clearance first, not sure if I'm going 15mm or 10mm in the front, will probably do those next week.

03-08-2009, 05:07 PM	#46 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 55 Posts: 5,995 Drives: People to drink Rep Power: 34	I did a little looking around on Google and found this: Wheel Stud Remover SA91107NE __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

03-09-2009, 10:36 PM	#49 (permalink)
alan93rsa Enthusiast Member Join Date: Feb 2009 Location: Ohio Posts: 412 Drives: 16 Cayman GT4 Red Rep Power: 222	The price isn't too bad if you add in the cost of damaging a hub or bearing beating a stud out. If two people went in on one the price would be half. Just need to find a local or be willing to ship it to the second person. There are a few tools which circulate on the NSX board which are not ones you would would want to own. I used the ABS bleeder for my NSX. You put your name on the list and the members just keep forwarding the tool. Not a bad deal until someone gets the tool and runs into issues getting their job done. __________________ 16 Cayman GT4, Carmine Red, Buckets, PCCB etc.

03-10-2009, 07:48 AM	#50 (permalink)
semtex A True Z Fanatic Join Date: Jan 2009 Location: Behind enemy lines Age: 55 Posts: 5,995 Drives: People to drink Rep Power: 34	^ I was kinda tossing the same idea around in my head. We could start a 'tool co-op'. __________________ "There are no small accidents on this circuit." -- Ayrton Senna 316.8whp & 248 ft/lbs (Dyno Dynamics) \| 319whp & 256 ft/lbs (DynoJet) (04/23/10) Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.

04-05-2009, 12:01 PM	#53 (permalink)
Minicobra1 A True Z Fanatic Join Date: Nov 2008 Location: Orange County, CA. Posts: 1,205 Drives: 370Z Tour, Spt, 6mt Rep Power: 646	Anyone know of a So-Cal shop that would do the install on the spacers? Someone that has the proper stud press tool and not a hammer. __________________ 370z Tour\| Spt Pack\|Navi\|BERK CBE\|Berk HFC's\| Eibach Springs\| Hotchkis Sway Bars\|SPC Camber Arms\|15mm Ichiba Wheel Spacers\| 19"Factory Nismo Wheels-Matt Black\|Stop Tech Rotors\|TWM Shifter\|3M Tint\|Black Fangs\|Black Rear Valance\|JDM Fog Light\| MY BAND-www.myspace.com/petroleum

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Stock Spoiler on the 370Z?	TacoZ	Exterior & Interior	36	11-06-2013 03:06 PM
Optional Stock Rims	nogoodname	Wheels & Tires	15	01-29-2009 04:59 PM
Stock GPS Antenna on Aftermarket Navigation	zero610	Audio & Video	0	01-28-2009 09:06 AM
Weight of stock wheels?	sbkim	Wheels & Tires	9	01-13-2009 09:57 PM
Stock Navigation Ipod interface	shizzawha	Nissan 370Z General Discussions	16	12-13-2008 03:24 PM

03-08-2009, 06:02 PM	#47 (permalink)
dlmartin81 Track Member Join Date: Dec 2008 Location: Chalfont, PA Age: 44 Posts: 923 Drives: 09 370Z Rep Power: 609	^^ hmmm good find.

03-18-2009, 11:14 PM	#52 (permalink)
VIP-STATUS Inactive vendor Join Date: Mar 2009 Location: Torrance,Ca Posts: 465 Drives: 2009 370Z Red Rep Power: 259	I say 15mm front+rear will be perfect