Kinetix front upper control arms

clintfocus · 06-06-2013, 10:25 PM

Quote:

Originally Posted by DR_

I took off the nut just to see how far they would go and I got -4.2 degrees. If you are willing to modify the arms it would be really easy to cut the extra off the end of the arm where the ball joint screws in. So doing that with a thinner nut and I bet -3.5 is achievable, which is probably more than enough.
I am monitoring tire temps at this weekend’s event to see how my –2.7 degree does.

this is what i did with my front Kinetix arms, my ride height isnt low and i have my front camber at -3, ill be switching to everything SPL soon though, and i got word from SPL that they are moving to production with their front upper arms

Sh0velMan · 06-07-2013, 07:17 AM

Quote:

Originally Posted by Dwnshift

Maybe you didn't read my post clearly.

The parts we design and produce jn house have been the same ones we have been racing with for over a year now.

BJ, PM me a price on a front bar, just so we can be sure that it's out of my price range, lmao.

DR_ · 06-07-2013, 08:15 AM

Quote:

Originally Posted by clintfocus

this is what i did with my front Kinetix arms, my ride height isnt low and i have my front camber at -3, ill be switching to everything SPL soon though, and i got word from SPL that they are moving to production with their front upper arms

I'll be moving over to all SPL as well. However, since I can get the rear camber I currently want with the rear stock alignment bolts (-2.0) and the front via the Kinetix arms (-2.7), I'm not in any real hurry.

Dwnshift · 06-07-2013, 11:54 AM

ImageUploadedByTapatalk1370624024.936416.jpg
Just incase you forgot.

BuckeyeZ · 06-07-2013, 11:54 AM

Quote:

Originally Posted by Dwnshift

If only there was a place that built quality race parts that worked ....
Hmmmm

So BJ, how do we go about getting some of these mysterious 'quality race parts' that you mentioned? I need front camber arms and will take a front sway as well. Can I get some in this lifetime?

Dwnshift · 06-07-2013, 02:12 PM

All you have to do is ask

I have one set of front upper control arms left from our first batch.
Drop me a PM and we can go from there.
Bjz

phunk · 06-07-2013, 02:49 PM

how much are those upper arms?

Dwnshift · 06-07-2013, 06:59 PM

Phunk...tried to reply but ur box is full.

Some other parts are also in development that others may think are a little more seat of the pants "fun"

First up : Headers.... Like no other set that is currently available.

The big project on the table may be THE hot ticket for power.

gomer_110 · 06-07-2013, 08:54 PM

Quote:

Originally Posted by Dwnshift

Phunk...tried to reply but ur box is full.

Some other parts are also in development that others may think are a little more seat of the pants "fun"

First up : Headers.... Like no other set that is currently available.

The big project on the table may be THE hot ticket for power.

Before anyone else can volunteer, I'll be more than happy to supply my car for testing on a street going Z in exchange for some discounted parts.

Building by own Doran Nismo RC one part at a time.

NOFATCHX · 09-16-2013, 09:21 PM

I need negative camber for other reasons then race. Car is lowered a good 2" with stock camber arms. I have negative camber if course due to my drop... My question is, will the Kinetix front camber arms provide me option to adjust for MORE negative camber?

GSS138 · 09-16-2013, 11:54 PM

Quote:

Originally Posted by NOFATCHX

I need negative camber for other reasons then race.

Sh1t just got weird.

synolimit · 09-17-2013, 01:54 AM

Quote:

Originally Posted by Sh0velMan

Haha!

I would love a Doran front bar, I just don't think you could sell me one for what i can afford! haha

He won't tell us his specs will he?

If you/someone had to guess, whats the stiffest setting on the whiteline come out to stiffness wise or compared to size wise of say the hotchkins at 37mm?

My OEM 13 is 26.5mm and hollow I believe. Curious as to whats the stiffest since I see doran say this all the time on threads.

PS whats everyone elses settings that they like? I was planning to go -2.5 front and -1.5 rear to start with a good size front bar and stock rear. Also plan to run someone's front camber arm like these kinetix (SPC looks scary), spl rear arms with my toe and camber bolt lockout kit so the bolts don't move under load. Camber will be adjusted in the spl arm only and the toe will be adjusted in the toe lockout plate with different drilled holes left or right from center.

synolimit · 10-01-2013, 10:26 PM

Quote:

Originally Posted by DR_

I took off the nut just to see how far they would go and I got -4.2 degrees. If you are willing to modify the arms it would be really easy to cut the extra off the end of the arm where the ball joint screws in. So doing that with a thinner nut and I bet -3.5 is achievable, which is probably more than enough.
I am monitoring tire temps at this weekend’s event to see how my –2.7 degree does.

Why is the nut needed? Seems impossible for the ball joint to unscrew out of the arm.

DR_ · 10-02-2013, 06:51 AM

It is needed so that the ball joint doesn't rock back and forth. The threads on the ball joint would wear out quickly and eventually fall off causing you to crash and die.

06-07-2013, 02:49 PM	#22 (permalink)
phunk A True Z Fanatic Join Date: Mar 2009 Location: Chicago Posts: 3,669 Drives: 370 Rep Power: 974724	how much are those upper arms? __________________ Charles @ CJ Motorsports : Website \| Facebook \| Instagram \| YouTube Home of the 9 second, stock longblock, stock drivetrain 6MT 370z. 9.91 @ 142mph

09-16-2013, 09:21 PM	#25 (permalink)
NOFATCHX Track Member Join Date: Apr 2011 Location: New York Posts: 532 Drives: 2011 370Z Rep Power: 16	I need negative camber for other reasons then race. Car is lowered a good 2" with stock camber arms. I have negative camber if course due to my drop... My question is, will the Kinetix front camber arms provide me option to adjust for MORE negative camber? __________________ 20x10.5 Vossen CV3s, Falken, Stillen, AAM, Topspeed, BC Racing, ICHIBA, 180 CUSTOM, Satin Pearl White and Carbon wrapped Instagram: 10acious_Z

10-02-2013, 06:51 AM	#29 (permalink)
DR_ Track Member Join Date: Jul 2009 Location: Dallas Posts: 981 Drives: Touring/Sport M6 PG Rep Power: 18	It is needed so that the ball joint doesn't rock back and forth. The threads on the ball joint would wear out quickly and eventually fall off causing you to crash and die. Sh0velMan likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[WTB] low mileage stock upper control arms	DR_	Parts for sale (Private Classifieds)	0	05-06-2013 02:43 PM
[FOR SALE] oem catback exhaust, upper control arms	roy'sz	Parts for sale (Private Classifieds)	16	01-31-2013 12:03 PM
Cusco front upper control arms	fuct	Brakes & Suspension	9	01-20-2013 12:43 PM
Kinetix Front Upper Arm	roy'sz	DIY Section (Do-It-Yourself)	0	10-22-2012 12:30 AM
[FOR SALE] Front upper Control Arms	pokeyl	Parts for sale (Private Classifieds)	1	10-16-2011 10:25 AM

06-07-2013, 11:54 AM	#19 (permalink)
Dwnshift Track Member Join Date: Feb 2012 Location: Cincy Posts: 717 Drives: NISMO 370Z RC Rep Power: 15	ImageUploadedByTapatalk1370624024.936416.jpg Just incase you forgot.

06-07-2013, 02:12 PM	#21 (permalink)
Dwnshift Track Member Join Date: Feb 2012 Location: Cincy Posts: 717 Drives: NISMO 370Z RC Rep Power: 15	All you have to do is ask I have one set of front upper control arms left from our first batch. Drop me a PM and we can go from there. Bjz

06-07-2013, 06:59 PM	#23 (permalink)
Dwnshift Track Member Join Date: Feb 2012 Location: Cincy Posts: 717 Drives: NISMO 370Z RC Rep Power: 15	Phunk...tried to reply but ur box is full. Some other parts are also in development that others may think are a little more seat of the pants "fun" First up : Headers.... Like no other set that is currently available. The big project on the table may be THE hot ticket for power.