Tying in a datalogger (DL1 in my case) to the ECU?

vjarnot · 05-06-2012, 04:22 PM

Just got a Z about a week ago. In my S2000, I was able to (fairly easily) tap into the ECU wiring to feed things like water temp, intake air temp, TPS, RPM, etc to my DL1.

Still finding my way around these forums... I did a bit of searching, but no luck.

So, I'd greatly appreciate it if anyone has any info on tying in to the 370z ecu with a datalogger. Surely it's been done?

And a noob question: where are the ecu connectors located on this car?

vjarnot · 05-07-2012, 08:37 PM

Help a noob out, folks. Did I drop a deuce in the punchbowl here? Is this a retarded question?

Surely someone has tapped in, either between sensors and ecu, or between ecu and dash gauges...

ZeN · 05-08-2012, 10:43 AM

Cheap way - buy OBD2 bluetooth ($20-30), pair it with your Android running Torque app, can datalog as much you want.

Too bad my JDM spec 370z is not OBD2 compliant

vjarnot · 05-08-2012, 10:50 AM

Thanks... I already have a datalogger.

sig11 · 05-08-2012, 01:43 PM

Check out travisjb's thread. I think he had a hard time even getting an RPM signal.

Edit: it's funny how no one is paying attention to you, vjarnot.

seymore4 · 05-08-2012, 02:13 PM

Buy an uprev cipher cable and datalog in cipher through the obd2, no need to hardwire anything

vjarnot · 05-08-2012, 02:22 PM

Thanks sig11, I've skimmed that whole thread... it's a bear! I'll check again, but I don't remember there being anything too useful on the datalogger front.

Quote:

Originally Posted by seymore4

Buy an uprev cipher cable and datalog in cipher through the obd2, no need to hardwire anything

Quote:

Originally Posted by vjarnot

Thanks... I already have a datalogger.

Owen · 05-19-2012, 10:28 AM

http://www.race-technology.com/seria...ce_8_7583.html

05-06-2012, 04:22 PM	#1 (permalink)
vjarnot Base Member Join Date: Apr 2012 Location: Mathews, AL Posts: 68 Drives: 2012 370Z Base SP M6 Rep Power: 14	Tying in a datalogger (DL1 in my case) to the ECU? Just got a Z about a week ago. In my S2000, I was able to (fairly easily) tap into the ECU wiring to feed things like water temp, intake air temp, TPS, RPM, etc to my DL1. Still finding my way around these forums... I did a bit of searching, but no luck. So, I'd greatly appreciate it if anyone has any info on tying in to the 370z ecu with a datalogger. Surely it's been done? And a noob question: where are the ecu connectors located on this car?

05-08-2012, 01:43 PM	#5 (permalink)
sig11 A True Z Fanatic Join Date: Jun 2009 Location: Detroit Posts: 1,294 Drives: 09 370Z Red Sport-MT Rep Power: 19	Check out travisjb's thread. I think he had a hard time even getting an RPM signal. Edit: it's funny how no one is paying attention to you, vjarnot. Last edited by sig11; 05-08-2012 at 02:14 PM.

05-19-2012, 10:28 AM	#8 (permalink)
Owen Base Member Join Date: May 2012 Location: CA Posts: 22 Drives: lots Rep Power: 14	http://www.race-technology.com/seria...ce_8_7583.html Last edited by Owen; 05-19-2012 at 10:34 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
anyone have a datalogger?	cossie1600	Track / Autocross / Drifting / Dragstrip	9	05-17-2011 01:43 PM
recommendations for scantool/datalogger	Pharmacist	Nissan 370Z General Discussions	3	12-01-2010 08:52 AM
In case you didn't know...	LunaZ	The Lounge (Off Topic)	15	06-07-2010 02:05 PM
Just in case???	Xavier Raymond	Nissan 370Z General Discussions	3	03-18-2009 01:33 PM

05-07-2012, 08:37 PM	#2 (permalink)
vjarnot Base Member Join Date: Apr 2012 Location: Mathews, AL Posts: 68 Drives: 2012 370Z Base SP M6 Rep Power: 14	Help a noob out, folks. Did I drop a deuce in the punchbowl here? Is this a retarded question? Surely someone has tapped in, either between sensors and ecu, or between ecu and dash gauges...

05-08-2012, 10:43 AM	#3 (permalink)
ZeN Base Member Join Date: Apr 2011 Location: Malaysia Posts: 116 Drives: 09 PW 7AT 370z Rep Power: 15	Cheap way - buy OBD2 bluetooth ($20-30), pair it with your Android running Torque app, can datalog as much you want. Too bad my JDM spec 370z is not OBD2 compliant

05-08-2012, 10:50 AM	#4 (permalink)
vjarnot Base Member Join Date: Apr 2012 Location: Mathews, AL Posts: 68 Drives: 2012 370Z Base SP M6 Rep Power: 14	Thanks... I already have a datalogger.

05-08-2012, 02:13 PM	#6 (permalink)
seymore4 Track Member Join Date: Nov 2010 Location: West coast Age: 42 Posts: 560 Drives: 2010 nismo Rep Power: 6727	Buy an uprev cipher cable and datalog in cipher through the obd2, no need to hardwire anything