Nissan 370Z Forum  

370Z Forums HOME My Picture Album Nissan 370Z Pictures Premium Membership Become a Forum Sponsor
Go Back   Nissan 370Z Forum > Search Forums
Reload this Page Search Results
Register All Albums FAQDonate Members List Calendar Today's Posts


Page 1 of 2 1 2
Showing results 1 to 25 of 40
Search took 0.00 seconds. Search: Posts Made By: Boosted Performance
Forum: Forced Induction 04-13-2020, 11:34 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Contact Tial, these are MV-S wastegates. They...

Contact Tial, these are MV-S wastegates. They will all have the same internals.
Forum: Forced Induction 04-12-2020, 11:11 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
6mm (1/4") is the correct size. ...

6mm (1/4") is the correct size.




GTR plugs.
Forum: Forced Induction 04-11-2020, 10:33 AM
Replies: 563
Views: 62,174
Posted By Boosted Performance
^^^^ Correct Kit comes with 6mm silicone...

^^^^ Correct

Kit comes with 6mm silicone hose, but 5mm should not make a difference.
Forum: Forced Induction 04-10-2020, 10:54 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Don't put a stiff spring in the BOV. The engine...

Don't put a stiff spring in the BOV. The engine vacuum at idle, when warm is what determines your BOV spring. Putting a stiffer spring than the vacuum can open, will cause issues.

Double check...
Forum: Forced Induction 03-25-2020, 06:15 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
It is -6AN female on both ends.

It is -6AN female on both ends.
Forum: Forced Induction 03-25-2020, 12:56 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
All you need to do is make sure the pump is...

All you need to do is make sure the pump is running (in the right direction). If it is you are good to go. You can always double check at the reservoir by loosening the AN fitting, you will hear...
Forum: Forced Induction 03-28-2019, 12:26 AM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Lengthy reply sent.

Lengthy reply sent.
Forum: Forced Induction 03-27-2019, 07:59 AM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Sorry, missed the PM....replied.

Sorry, missed the PM....replied.
Forum: Forced Induction 02-17-2019, 11:19 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
With the fuel pump relay, there are two wires...

With the fuel pump relay, there are two wires that go to the fuel pump, one to ground, and another to the battery.

If you have a picture, please post it or send it to me and I will tell you what...
Forum: Forced Induction 01-24-2019, 12:27 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
There has to be an issue somewhere in the...

There has to be an issue somewhere in the plumbing. I see the power output in your signature, is that where the issues is, or is it when you are just on spring pressure, with the EBP installed, but...
Forum: Forced Induction 01-23-2019, 11:59 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Yes, you can use any spring you want, as long as...

Yes, you can use any spring you want, as long as the car is tuned for it.

As for "boost creep", I am not sure that it is understood. Boost creep is an uncontrolled increase in boost as the RPM's...
Forum: Forced Induction 01-22-2019, 09:46 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
I have not heard of any customers having issues...

I have not heard of any customers having issues with any boost creep.

What springs are in the gates, and what is the actual boost being seen? Also, which boost controller, and where is the boost...
Forum: Forced Induction 01-22-2019, 12:15 AM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Unless the gate is malfunctioning, there is...

Unless the gate is malfunctioning, there is really no reason to take it apart. Once the crews are out, there is nothing else holding the top cap in place. So be careful as the spring can send things...
Forum: Forced Induction 12-22-2018, 07:33 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
There are no shear pins, there is a key to hold...

There are no shear pins, there is a key to hold the gear on to the shaft as it rotates. It is not possible for the key to come out with the cover on, and the gear in place. It is not a large key, so...
Forum: Forced Induction 11-25-2018, 04:14 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
I'll PM you the install manual link. As...

I'll PM you the install manual link.


As for the top bolt, pull the oil reservoir off the turbo, and use a wrench from the transmission side.
Forum: Forced Induction 11-05-2018, 12:30 AM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Yeah, that is normal. My Precision ball bearing...

Yeah, that is normal. My Precision ball bearing did the same thing. Once the COMP turbo is broken in, it spools fast/hard. Mechanical efficiency is extremely high with these units.
Forum: Forced Induction 11-05-2018, 12:25 AM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Well, I would start by pulling the turbo, or at...

Well, I would start by pulling the turbo, or at least the down pipe to see if the rotating assembly spins freely. If all is good there, check the oiling system, and ensure the pumps pulling vacuum at...
Forum: Forced Induction 11-04-2018, 02:10 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
A lot of them have been install related. I would...

A lot of them have been install related. I would say that the COMP turbos are performing better than the standard Precision JB turbos the kit came with.

The other REALLY BAD part about the...
Forum: Forced Induction 05-04-2017, 11:38 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
PM your ship to address and I'll get a BOV spring...

PM your ship to address and I'll get a BOV spring shipped over to you.
Forum: Forced Induction 04-23-2017, 07:20 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Anywhere on the intake manifold. A cheap gauge...

Anywhere on the intake manifold. A cheap gauge will do just fine.
Forum: Forced Induction 04-22-2017, 10:33 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
You guys are confusing BOV springs and wastegate...

You guys are confusing BOV springs and wastegate springs. Glad you got it all figured out. Let me know what your vacuum is at idle and I'll get you the correct BOV sent.
Forum: Forced Induction 04-15-2017, 03:16 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
You need to find out what your vacuum is at idle,...

You need to find out what your vacuum is at idle, with the engine fully warmed up. From there you need to get the correct BOV spring. I am guessing your vacuum will be in the -18 to-19 Hg. Which...
Forum: Forced Induction 04-15-2017, 08:08 AM
Replies: 563
Views: 62,174
Posted By Boosted Performance
With a new/built engine, you need find out what...

With a new/built engine, you need find out what your vacuum is at idle, while the engine is hot. Based on this, you may need to change the BOV spring:
...
Forum: Forced Induction 04-07-2017, 08:58 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
The turbo is good for 30psi...but remember,...

The turbo is good for 30psi...but remember, pressure is resistance to flow. So if the turbine is too small, the pressure will go up, but power won't.

The telling sign that you have reached turbine...
Forum: Forced Induction 04-06-2017, 11:09 PM
Replies: 563
Views: 62,174
Posted By Boosted Performance
Exhausts size won't be an issue at all. If you...

Exhausts size won't be an issue at all. If you have emissions that will be a bit restrictive. To get to 600whp on pump, 17psi should do the trick. Ideally, the 1.32 a/r housing is key, and I don't...
Showing results 1 to 25 of 40
Page 1 of 2 1 2

 
Forum Jump

All times are GMT -5. The time now is 05:33 AM.

Contact Us - Home Page - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2