Nissan 370Z Forum  

Wavering Idle and Dropping Voltage

The issue is permanently fixed and voltage steady as a rock at 14.5 like it was for the last 10 years. I did place a response and if you cannot

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs


Like Tree13Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 05-20-2020, 01:27 PM   #31 (permalink)
Base Member
 
Javier's Avatar
 
Join Date: Jan 2010
Location: Illinois
Posts: 40
Drives: 09 nissan 370z
Rep Power: 10138
Javier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond repute
Default

The issue is permanently fixed and voltage steady as a rock at 14.5 like it was for the last 10 years. I did place a response and if you cannot find it follow this video to the letter.

https://www.youtube.com/watch?v=vYtyDX9RTWs

Like I stated on my response the battery voltage my swing back onc or twice while the car re-calibrates itself.
cv129 and Rusty like this.
Javier is offline   Reply With Quote
Old 05-20-2020, 03:20 PM   #32 (permalink)
Premium Member
 
SouthArk370Z's Avatar
 
Join Date: Nov 2010
Location: South Arkansas
Posts: 8,435
Drives: 2014 Challenger
Rep Power: 324197
SouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond reputeSouthArk370Z has a reputation beyond repute
Default

Or you could take one of the battery terminals loose and step on the brake pedal for a few seconds. Will work with any car that has functioning stop lights when the car is turned off (ie, all of them).

There IS a good reason to take the negative terminal off first - if your wrench shorts to ground, you won't have a dead short. Once the neg is loose, shorting the positive to ground won't hurt.

Putting a dead short (the jumper in the video) across charged capacitors is a bad idea. The rapid discharge can damage capacitors and other elements inside the ECM. Most are rugged enough to handle it but why take the chance? If you use the jumper-wire method, put a resistor in series.
__________________
Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub
Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma
SouthArk370Z is offline   Reply With Quote
Old 05-20-2020, 03:21 PM   #33 (permalink)
Ronin Samurai - Assassin
 
Rusty's Avatar
 
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 68
Posts: 34,813
Drives: 2011 Nismo GM 6M
Rep Power: 2684436
Rusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond repute
Talking

Quote:
Originally Posted by Javier View Post
The issue is permanently fixed and voltage steady as a rock at 14.5 like it was for the last 10 years. I did place a response and if you cannot find it follow this video to the letter.

https://www.youtube.com/watch?v=vYtyDX9RTWs

Like I stated on my response the battery voltage my swing back onc or twice while the car re-calibrates itself.
Nice job on finding that.
__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html
Rusty is offline   Reply With Quote
Old 07-24-2020, 12:49 AM   #34 (permalink)
Base Member
 
Javier's Avatar
 
Join Date: Jan 2010
Location: Illinois
Posts: 40
Drives: 09 nissan 370z
Rep Power: 10138
Javier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond reputeJavier has a reputation beyond repute
Default Voltage drop with idle drop at idle only

As I had previously posted, I thought my problems where over when I discharged all the car capacitors. Wrong it cam back shortly after that, again the idle and the battery voltage fluctuating at idle. I found the true fix for this and you probably are going to think I'm nuts but here we go. When I replaced my original alternator that fried itself I followed the installation procedures in the manual under CHG (charging) in that section it tell you to go to EM (engine mechanical) to check tension. This is by checking the tensioner and making sure that it is between the lines as shown in EM-13. Here is where the fun begins, I found that my belt was at the last line which indicated it should be replaced. I had just replaced the belt 40k ago, then in EM-13 it says tension adjustment refer to : EM-139 DRIVE BELT. Wonderful, I go to that page and it states no adjustment needed self tensioning. I started my t/shooting again. I removed the serpentine belt. I found that the alternator stay item 6 on CHG-24 has the hole that attaches to the engine side elongated. It's not plug and play, I wedge a piece of wood between the alternator and the engine to force the alternator as far out as it could go. Then I torqued all the bolts, installed the serpentine belt and behold the tension was perfect in between the limits indicated by "B" on EM-13. I started the car and behold all perfect just like before my battery and alternator crapped out. No where does it tell you about the alternator stay adjustment. Now I do not know if a bushing or sleeve may have fallen out of my stay but from the pictures I have seen there are none. At idle the belt is hardly touching the pulley even with the tensioner in place. Its been a two weeks since I did this and all ok. So I loosened up the alternator stay and retorqued it without taking up the slack and the car started acting up again. So at least in my case I have confirmed the cause of my problems.3 batteries 3 alternators, 2 mass air flow sensors and numerous hours later it is fixed. Hope this helps some of you.

[IMG][/IMG]


http://www.the370z.com/members/javie...nator-stay.jpg

http://www.the370z.com/members/javie...-tensioner.jpg

Last edited by Javier; 07-24-2020 at 01:36 AM. Reason: adding additional info
Javier is offline   Reply With Quote
Old 08-09-2020, 02:25 PM   #35 (permalink)
Enthusiast Member
 
Join Date: Apr 2014
Location: Utah
Posts: 379
Drives: 2014 370z M.B. 7AT
Rep Power: 3365
markesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond repute
Default

Hello everyone!

Could GREATLY use help on this.

So as my above post mentions, I had the stock battery last for around 6 years / 60k miles. One day all of a sudden my bass amp (RF) just self destructed, and so did one of my JL Audio 10w3's. So bad, that the entire interior smelled like an electrical melt down! Pulled Sub box, and stopped using amp.

A month later, the stock battery would not start the car without a jump start. Took to dealership, had battery replaced. Everything was FINE.

Until about 2.5 weeks ago I stopped driving the car every day, and would let it sit in the garage for 2-3 days. Then one day it wouldn't start without a jump start. Then 2 days later, car starts on it's own just fine. Then a day after that, completely DEAD. Not a single light on the dash, nothing works at all. My tiny taclife jumpstart battery failed to work even after charging it to the max.

So called the insurance company, tow truck dude shows up with a giant jump start battery type (the blue one with the handle). Car turns over slowly and finally started after about 3-4 seconds.

Drive car straight to dealer - dealers tests battery and shows me a receipt tape like print out stating the battery they put in there 4 months ago is just fine.

Since then, I've been just disconnecting the negative terminal if I need to let the car sit for more than a few hours as I'm now working from home like everyone else.

One thing I've noticed, which is similar to others posts: the voltage meter.

Recently at stop lights, I notice the voltage drop to one tick below 14, and then if I'm driving for quite a while at 80+mph on the freeway, then it will slowly go back above to 14.1-3ish. In the past 6+ years of ownership, that battery voltage thing barely moved, and now it's moving around consistently, especially at stop lights. I've also had that strange idle rise/fall only once at a single stop light.

Other facts: 72,000 miles on the car now, serpentine belt has never been changed, stock alternator, battery replaced 4 months ago, and I did relocate to phoenix (hot as an oven) in January - The heat here kills just about everything, and I'm told by many that it's not uncommon to only get 18-24 months out of a typical battery. I did finally completely remove the dead RF amp that may have been doing some type of parasitic draw, but it does not seemed to have changed any behavior of the volt meter. Other than that, I'm running a 5 year old pioneer deck going to a 4 channel RF amp that was installed at a stereo shop. I did check to see if the amp that is working shuts off, and it does.

I'm open to suggestions on where to look next, and I may simply have to start with cheapest stuff first: serpentine belt ? (mine is about dead center per the diagram below)

Please advise if anyone has any ideas.






Quote:
Originally Posted by Javier View Post
As I had previously posted, I thought my problems where over when I discharged all the car capacitors. Wrong it cam back shortly after that, again the idle and the battery voltage fluctuating at idle. I found the true fix for this and you probably are going to think I'm nuts but here we go. When I replaced my original alternator that fried itself I followed the installation procedures in the manual under CHG (charging) in that section it tell you to go to EM (engine mechanical) to check tension. This is by checking the tensioner and making sure that it is between the lines as shown in EM-13. Here is where the fun begins, I found that my belt was at the last line which indicated it should be replaced. I had just replaced the belt 40k ago, then in EM-13 it says tension adjustment refer to : EM-139 DRIVE BELT. Wonderful, I go to that page and it states no adjustment needed self tensioning. I started my t/shooting again. I removed the serpentine belt. I found that the alternator stay item 6 on CHG-24 has the hole that attaches to the engine side elongated. It's not plug and play, I wedge a piece of wood between the alternator and the engine to force the alternator as far out as it could go. Then I torqued all the bolts, installed the serpentine belt and behold the tension was perfect in between the limits indicated by "B" on EM-13. I started the car and behold all perfect just like before my battery and alternator crapped out. No where does it tell you about the alternator stay adjustment. Now I do not know if a bushing or sleeve may have fallen out of my stay but from the pictures I have seen there are none. At idle the belt is hardly touching the pulley even with the tensioner in place. Its been a two weeks since I did this and all ok. So I loosened up the alternator stay and retorqued it without taking up the slack and the car started acting up again. So at least in my case I have confirmed the cause of my problems.3 batteries 3 alternators, 2 mass air flow sensors and numerous hours later it is fixed. Hope this helps some of you.

[IMG][/IMG]


http://www.the370z.com/members/javie...nator-stay.jpg

http://www.the370z.com/members/javie...-tensioner.jpg

Last edited by markesc; 08-09-2020 at 02:30 PM. Reason: serpentine belt notch setting
markesc is offline   Reply With Quote
Old 08-21-2020, 07:21 PM   #36 (permalink)
Enthusiast Member
 
Join Date: Apr 2014
Location: Utah
Posts: 379
Drives: 2014 370z M.B. 7AT
Rep Power: 3365
markesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond repute
Default

Well finally got a SES or " Service Engine Soon " light... will have to buy code reader and go from there.

Was hoping some people could chime in with ideas before the stealership tries to BK me! Will post again with update

Last edited by markesc; 08-21-2020 at 07:42 PM.
markesc is offline   Reply With Quote
Old 08-21-2020, 07:56 PM   #37 (permalink)
Track Member
 
Join Date: Apr 2015
Location: Columbus OH
Posts: 612
Drives: Z34|C4LT4|C6Z06|V25
Rep Power: 3365
POS VETT has a reputation beyond reputePOS VETT has a reputation beyond reputePOS VETT has a reputation beyond reputePOS VETT has a reputation beyond reputePOS VETT has a reputation beyond reputePOS VETT has a reputation beyond reputePOS VETT has a reputation beyond reputePOS VETT has a reputation beyond reputePOS VETT has a reputation beyond reputePOS VETT has a reputation beyond reputePOS VETT has a reputation beyond repute
Default

Can you scan for the DTC?
POS VETT is offline   Reply With Quote
Old 08-21-2020, 09:26 PM   #38 (permalink)
Enthusiast Member
 
Join Date: Apr 2014
Location: Utah
Posts: 379
Drives: 2014 370z M.B. 7AT
Rep Power: 3365
markesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond repute
Default

Quote:
Originally Posted by POS VETT View Post
Can you scan for the DTC?
That's the plan, still looking at scanners on amazon at this point...

** ordered charging system tester and 3-in-1 tester/code reader/multi-meter; Figure whynot have both and have some redundancy. **

Last edited by markesc; 08-22-2020 at 03:10 PM. Reason: update
markesc is offline   Reply With Quote
Old 08-23-2020, 09:31 PM   #39 (permalink)
Enthusiast Member
 
Join Date: Apr 2014
Location: Utah
Posts: 379
Drives: 2014 370z M.B. 7AT
Rep Power: 3365
markesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond reputemarkesc has a reputation beyond repute
Default

Quote:
Originally Posted by POS VETT View Post
Can you scan for the DTC?
Well... not really sure what to say now...aka: dog chasing tail!

P0603 So this must be just from leaving the battery disconnected a few days which is what I've been doing out of fear that I have some parasitic draw or god knows what at this point.

As stated above, it wouldn't start after 3 days of sitting with avg temps in the 110-120 degree range outside (car is garaged).

Tester says the charging system: battery, starter draw, alternator are fine...

Here's my plan: Leave battery connected, test it each day, and go from there.
markesc is offline   Reply With Quote
Old 12-29-2023, 03:03 PM   #40 (permalink)
Base Member
 
Join Date: Jul 2015
Location: Houston
Posts: 50
Drives: 09 AW 370Z Sport 6MT
Rep Power: 9
JSON is on a distinguished road
Default

Bumping this back up. I've noticed my car didn't start after a week of no activity. The battery was about 9 months old, but I went to the shop and they recharged it. It then started up fine. It's been fine for a few weeks but just noticed that my voltage fluctuates from 12V to the normal 14.5V or whatever. I've never seen it dip that low. I noticed even while driving, it goes from 12 to 14, then stays at the normal 14.

Is my alternator going? Not charging the battery consistently? That doesn't seem quite correct either.... Thoughts?
JSON is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Dropping In from Another Family of Z's! Junkman2008 New Forum Member 47 03-27-2011 09:12 PM
370Z Japanese voltage question... marcussoori Nissan 370Z General Discussions 9 12-16-2009 06:48 PM
Idle after installing the Gen3 Knives Engine & Drivetrain 18 12-05-2009 12:56 PM
voltage ,what does your car read? havasuwiley Nissan 370Z General Discussions 11 11-14-2009 12:26 PM
HELP PLEASE: Engine Idle Problem myfirstz Engine & Drivetrain 21 06-29-2009 05:40 PM


All times are GMT -5. The time now is 10:48 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2