What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY)

loiro370z

Installed mesh on my nismo bumper (home depot hack)

kenchan

ouch. i had dat happen on my old lowered G.. sucks. u getting a plastic replacement or the metal shroud?

jchammond

Gonna check it out-may build one or get the Z-speed that's all ready fabbed....oil pan is spotless...nicked the engine cradle

__________________
MazWorx built long block | FI-TT-100 Stage 2.75 | IPT built 7A/T

http://www.the370z.com/members-370z-...s-musings.html

Spoiler

Wow, Lucky it wasnt worse...

DeliriousClam

You're making me miss my Nismo bumper. I need to refinish it

__________________
Stillen, AAM, Shine Auto, Fujimora, Swift, EVO-R, Carbon Fiber Element, Nitrous Outlet
MECP Advanced: CEA26671
Most of what I post here are artistic works of fiction and falsehood. Only a fool would take anything I post here as fact.

jchammond

Also was an excuse to cut some fresh lumber to set on. 2/4x6's w/4x4 in center....rear tires take up about the whole 15"


Sent from my iPhone using Tapatalk

__________________
MazWorx built long block | FI-TT-100 Stage 2.75 | IPT built 7A/T

http://www.the370z.com/members-370z-...s-musings.html

OldFart

Had everything to do it, just didn't have the gonads to follow through. Had a fitted car cover this year and in two wind storms blew the cover off except it stayed on because of the mirror pockets. With it flappin' in the wind some scuff marks appeared, last weekend worked on the spoiler and came out nice, figured tonight I would work on my 3 year old VIS AMS hood. Took about 3 hours, car is sitting inside because I put a sealer on it. For 3 years old (hood), me thinks it looks pretty good, each night I'll do a panel or 2 until I'm done or it kills me.

Here are the results.

jchammond

Bout got lift-kit on the ~Z~
Be thankful if you have concrete/as it's becoming a higher priority!


Sent from my iPhone using Tapatalk

__________________
MazWorx built long block | FI-TT-100 Stage 2.75 | IPT built 7A/T

http://www.the370z.com/members-370z-...s-musings.html

mishuko

Picking up the car today from the shop. I hope lol

DeliriousClam

Cleaned the throttle bodies and air filters. For some reason one throttle body was much dirtier than the other

__________________
Stillen, AAM, Shine Auto, Fujimora, Swift, EVO-R, Carbon Fiber Element, Nitrous Outlet
MECP Advanced: CEA26671
Most of what I post here are artistic works of fiction and falsehood. Only a fool would take anything I post here as fact.

40 to 332

Was it the driver bank that was dirtier? That's what I noticed when I cleaned mine last week. Some of the residue along the edge of the butterfly valve was virtually impossible to remove, even after repeated application of throttle body cleaner.

DeliriousClam

Actually driver side was pretty clean. Passenger side was blacker than my soul

__________________
Stillen, AAM, Shine Auto, Fujimora, Swift, EVO-R, Carbon Fiber Element, Nitrous Outlet
MECP Advanced: CEA26671
Most of what I post here are artistic works of fiction and falsehood. Only a fool would take anything I post here as fact.

DeliriousClam

Got my alignment done finally. Hooks if I want it to and will break loose if I want it to. I'm liking these Nittos so far.

Awesome feeling too when I bring the 370 to a shop like that where they have GT-R's and other cars like that on a daily basis and they all tell me that it's one of the nicest cars they've seen in a while

__________________
Stillen, AAM, Shine Auto, Fujimora, Swift, EVO-R, Carbon Fiber Element, Nitrous Outlet
MECP Advanced: CEA26671
Most of what I post here are artistic works of fiction and falsehood. Only a fool would take anything I post here as fact.

mishuko

lol there was an rs3 when I dropped my car off... then when I went to pick up there was a gtr, 911 turbo-s and another carerra grrrr

felix0121

I had been to the dearlership with 'service engine soon' light up. They said something got inside to air-pressure sensors by accident, and cleared it so now no problem.

Sent from my SM-G930V using Tapatalk