:tup:

Got me some pmu decals for extra stoppage powah :bowrofl:

http://www.the370z.com/attachment.ph...0&d=1403903643

True... i just hate things not being symmetrical. O well i guess i will pull it off entirely.

I was staring at my sleeping beauty in my car port today. I then realized not only do I need a cover to keep her clean, but a solution to stopping my neighbors menice Felis catus from sleeping on it.

BB gun.

Me too. That's why I debadged the "370Z" (and replaced the Nissan emblem with the satin "Z" from thezstore.com.) Less is more. :tup:

You can't really mistake a 370Z for anything else, nor a Nismo for a base/touring Z either.

It's not like you need to keep that "M3" badge on your 3-series to distinguish yourself from a 320i, 328i, 328d and 335i. :roll eyes:

My old M3 was debadged funnily enough.

Also, loving the Z badge on your ride :tup::tup: Looks almost factory and beautiful. I looked on Z store could not locate it.

Is this what you got?

http://www.ebay.com/itm/2009-2014-JD...a7c01b&vxp=mtr

Oops. My bad. Lol. :wtf2:

Thank you!

I made some edits that you perhaps missed. Please respond LOL :roflpuke2:

Yup, those are the ones! I wonder why the ebay ones are so much cheaper...? :confused:

Limeybastard -

Here are some close up pics...

Thank you. I am getting these. For as it was for you the importance of removing the 370z badge also. I think these badges in satin work perfectly with the satin door pulls and also just making the car a Z above all with no other fuss nor muss!

Your post gave me inspiration:tup:


I was researching and noticed this.. http://www.350z-uk.com/topic/81826-s...70z-z-emblems/ these ones appear to be thicker and more three dimensional than the one from ebay which appear flatter.

Drove it to pick up some trans fluid for the beater car. Traffic and construction ruined my mood.

:shakes head:

:tiphat:

Yup! Perfect match for the door handles and the silver satin "Z" in the side markers/turn signals too. :tup:

Just be patient - the factory emblem "glue" is a PITA to remove. :shakes head:

Post me a link of where you got those Z emblems please, ta.

Motorsport! 370Z "Z" Logo Front Emblem, Satin Silver, 09-14 370Z - The Z Store! Nissan-Datsun 240Z-260Z-280Z-280ZX-300ZX(Z31/Z32)-350Z-370Z Parts

Motorsport! 370Z "Z" Logo Rear Emblem, Satin Silver, 09-14 370Z - The Z Store! Nissan-Datsun 240Z-260Z-280Z-280ZX-300ZX(Z31/Z32)-350Z-370Z Parts

My truck has been at the mechanic from last Friday to yesterday getting the power steering cooler replaced. The Z had to pull daily driver duty during that period and had gotten pretty nasty. Took a few hours this evening to clean inside & out and slap on a fresh coat of Rejex.
She's shiny again! :tup:

I'm in the process of pulling the trans for a lightweight flywheel. This is taking longer than expected...

I did mine a couple months ago... Not fun. Good luck :tup:

The transmission is off of the car!

It was a hard fought battle. Here's hoping the rest goes smoothly.

I have headers coming tomorrow. We'll see which is more difficult. I'm most likely not going to bolt the tranny back on until those are installed as well.

So today is end of week two of ownership! Picked up tags from dealer on way home from work yesterday (1st mod!). Then this morning, washed her for the first time, mainly just to get off bugs - about 20 miles of highway driving daily. Found a small 1/2 scratch on passenger side just below and in front of the "Z" and when I pulled off the front plate bracket to get the bugs off (maintenance just affixed bracket over bugs), I found the plate screws had dug into the paint (even though I asked them to make sure they didn't do that). After my initial "eek", I calmed back down knowing that I can likely buff/wax out the small scratch and the paint behind the front plate will always be covered as long as I own the car! Then I realized I have no tools to properly maintain a car at home (last car went to automatic car wash weekly), so ordered supplies that will be here before next week!

motored my z this am. :D that tpms cover i made a week or so ago is :tup: i had to look for it in the cluster.

went over 15k miles today.

qd'ed afterwards.

Finished my GTMat project in the Z. Last weekend I did the entire trunk area. Wow... what a difference in road noise. And the constant rock noises from the rear wheel wells is finally gone. Did both doors earlier this morning. Not as much difference in sound as the trunk area, but I do have to say the crappy stock radio has more base tone. And it's a little quieter too. Overall, one of the best mods I've done. Next weekend... new tunes!

Gave her a nice wash had a little photoshoot! :tup:


-M-

Which product did you go with?

i thought you said they were all garbage? :confused: ;)

;) Just wanted to see if they went with the worst garbage or not. :p

I was thinking of asking them to be an outside sales person. I've found out that they lost a lot of people and money shortly after I was let go. :tup:

:icon18:

:tup: that's cool to hear they're suckin' without you. :D they need you back! :tup:

you're suppose to post picts? :confused:

Drove it all over this morning. Racked about about 120miles when all said and done. good times :tup:

New tires. Conti DWS, alignment and road force balancing. $1166. Cha-ching!

How do you like the conti's?

So far, so good. I haven't put too many miles on them yet. I had DWs that were severely cupped, so the quiet is a welcome change.
I am extremely thrilled with the price that I got. The first place that I went to quoted me over $1600 for just the tires.

Finally finished removing the stock headers. Now to do it all over again, in reverse...

:icon18:GL!:tup:

I have envy.

Early morning Sunday drive about 70miles bought some 9mm ammunitions at Walmart ate breakfast at Ihop then off to do car wash.
Then...
Target shooting at the range.:tup:

Yup after working 13days straight i need some stress release or Il be "onzedge" :tup:

Ha!

Be careful of trademark infringement.

:icon17:

onzedge™ has written

Rep freely and often.