Adding oil cooler problem on 2014

SunsetZ · 02-05-2014, 04:48 PM

Finally got around to installing my Z1 Motorsports/Setrab 34 row oil cooler, and guess what, it won't work on my 2014. Seems my car has an extra collar like thing on the side of the oil pan where the filter attaches. This takes up about two inches and make it impossible to get a wrench on the filter to loosen or tighten. Looking at pics in the DIY oil change section, and this part is definitely not present on earlier models. Is this plumbing for and extra cooler that earlier models don't have? This blows!

screen shot capture

wrxrcr · 02-05-2014, 05:05 PM

I got a cooler on my 2012 with the factory cooler. Granted it was a PITA and you don't arrange the lines the same as you would a pre factory oil cooler Z.

mab864 · 02-06-2014, 07:27 AM

subed. Don't have any answers OP but facing the same thing on my '13. Wish I could just take off the lame little cooler and put on a 34 row. Good luck on the project.

Mt Tam I am · 02-06-2014, 08:29 AM

With my 2009 Z, and having lived through previous threads about oil coolers, this is a strange turn of events. I wish you luck.

Cmike2780 · 02-06-2014, 08:35 AM

You already have an oil cooler. Are you tracking this car and hitting limp mode?

onzedge · 02-06-2014, 09:19 AM

Quote:

Originally Posted by Mt Tam I am

With my 2009 Z, and having lived through previous threads about oil coolers, this is a strange turn of events. I wish you luck.

helidriver · 02-06-2014, 09:48 AM

If I'm understanding correctly, I think the OP's saying there won't be enough room to get a wrench on the end of the filter with both the factory and Z1 sandwich plates installed. It's going to be tight, but should fit. You won't be able to use a wrench, but the filter should only be hand tight anyways.

03g35coupe6mt · 02-06-2014, 10:27 AM

that is the stock oil cooler . couldnt you just unbolt that one and cap off the antifreeze lines and put the thermostatic sandwich plate in its place for the new cooler?

SunsetZ · 02-07-2014, 02:10 PM

Quote:

Originally Posted by 03g35coupe6mt

that is the stock oil cooler . couldnt you just unbolt that one and cap off the antifreeze lines and put the thermostatic sandwich plate in its place for the new cooler?

Z1 did say that is an option, just not sure what will be there if I remove the cooler, might need extra parts and could get in over my head for DIY.

onzedge · 02-07-2014, 02:13 PM

Quote:

Originally Posted by 03g35coupe6mt

that is the stock oil cooler . couldnt you just unbolt that one and cap off the antifreeze lines and put the thermostatic sandwich plate in its place for the new cooler?

No offense, but this is a bad idea.

03g35coupe6mt · 02-08-2014, 08:29 AM

well not cap them off i meant more like connect those two lines together dont know i dont have a 2014 i have a 2010 .

gurneyeagle · 02-08-2014, 08:32 AM

You just need to use a shorter filter. This came up with some friends in Houston.

I'll ask around and get the filter number.

helidriver · 02-08-2014, 08:33 AM

The factory size will fit.

03g35coupe6mt · 02-08-2014, 08:49 AM

DIY 2012 25 row Setreb Series 9 Install & stock oil cooler delete

Tigger · 02-08-2014, 10:05 AM

If you value a warranty then do NOT touch the stock oil cooler. Don't mess with it. Don't try to bypass it. Unless of course you bought a brand new car to beat the crap out of at a track.

The oil filter size you need is the HP-2008. I used that when I put my sandwich plate on my stock cooler and it fit just fine.

So this doesn't turn into another stupid debate over whether you need an extra oil cooler or not, feel free to visit other threads here relating to an aftermarket cooler on top of the stock cooler. You will see plenty of butt-hurt opinions and the like. Take it all with a grain of salt.

Bottom line. If you don't track it, don't "NEED" it. But my personal opinion is still quite different from this and I'll leave that out for now. Someone might get their feelings hurt.

Good luck to ya!

02-05-2014, 04:48 PM	#1 (permalink)
SunsetZ Base Member Join Date: Oct 2013 Location: Orlando Posts: 70 Drives: on the edge Rep Power: 11	Adding oil cooler problem on 2014 Finally got around to installing my Z1 Motorsports/Setrab 34 row oil cooler, and guess what, it won't work on my 2014. Seems my car has an extra collar like thing on the side of the oil pan where the filter attaches. This takes up about two inches and make it impossible to get a wrench on the filter to loosen or tighten. Looking at pics in the DIY oil change section, and this part is definitely not present on earlier models. Is this plumbing for and extra cooler that earlier models don't have? This blows! screen shot capture __________________ 2014 370Z 6MT Sport Midnight Blue 2013 GT-R Aurora Flare Blue Pearl Last edited by SunsetZ; 02-05-2014 at 04:59 PM.

02-06-2014, 07:27 AM	#3 (permalink)
mab864 Enthusiast Member Join Date: Nov 2013 Location: Oregon Posts: 482 Drives: 13 Sport 6MT Rep Power: 11	subed. Don't have any answers OP but facing the same thing on my '13. Wish I could just take off the lame little cooler and put on a 34 row. Good luck on the project. __________________ Berk HFC & CBE, Stillen G3, UpRev & tune by PSI, GTMat, 3M, Swift, StopTech, H&R 20/25, GT-R, 324 whp & 262 torque Last edited by mab864; 02-06-2014 at 07:30 AM.

02-06-2014, 08:29 AM	#4 (permalink)
Mt Tam I am A True Z Fanatic Join Date: Jun 2010 Location: California Posts: 10,709 Drives: 370Z T/S/N 6MT & XKE Rep Power: 3842	With my 2009 Z, and having lived through previous threads about oil coolers, this is a strange turn of events. I wish you luck. onzedge likes this. __________________ "Does the carpet match the drapes? NO!!! I don't date bald women." Nissan Motorsports 34R Oil Cooler. Stillen CBE. Hotchkis Sport Sway Bars. KW Variant 3 Coilover System. Stillen Gen3 CAI. Michelin Pilot Super Sport. Stillen Brake Ducts. Carbotech™ XP10/XP8 Pads. Z1 Front Rotors. Z1 Stainless Brake Lines. Two degrees of camber

02-06-2014, 08:35 AM	#5 (permalink)
Cmike2780 A True Z Fanatic Join Date: Jun 2010 Location: Long Island Posts: 5,059 Drives: slowwww Rep Power: 28	You already have an oil cooler. Are you tracking this car and hitting limp mode? kenchan and falconfixer like this. __________________ [09][MB][6-Spd MT][Touring][Stillen Gen III][K&N][Borla CBE][Evo-R] [ArchitTEK Photography]

02-08-2014, 08:32 AM	#12 (permalink)
gurneyeagle A True Z Fanatic Join Date: Jul 2011 Location: Houston/Saint Augustine Posts: 2,681 Drives: '18 Audi TT RS Rep Power: 20214	You just need to use a shorter filter. This came up with some friends in Houston. I'll ask around and get the filter number. __________________ Waiting on the Z35! SOLD - 2011 Gun Metallic Touring 7AT w Sports Pkg & Nav, Nismo Bumper and Rims, RC Grille, RC Brake Ducts, H&R Spacers, Painted Door Hdls, GTR Start Button, Nav By-Pass, EVO R Fog Light, CF Ducktail, CF Interior Trim

02-05-2014, 05:05 PM	#2 (permalink)
wrxrcr Base Member Join Date: Nov 2013 Location: columbus Posts: 74 Drives: 12 370z,09 Wrx Rep Power: 11	I got a cooler on my 2012 with the factory cooler. Granted it was a PITA and you don't arrange the lines the same as you would a pre factory oil cooler Z.

02-06-2014, 09:48 AM	#7 (permalink)
helidriver Base Member Join Date: May 2012 Location: The Woodlands, TX Posts: 37 Drives: '12 370Z Sport 6MT Rep Power: 12	If I'm understanding correctly, I think the OP's saying there won't be enough room to get a wrench on the end of the filter with both the factory and Z1 sandwich plates installed. It's going to be tight, but should fit. You won't be able to use a wrench, but the filter should only be hand tight anyways.

02-06-2014, 10:27 AM	#8 (permalink)
03g35coupe6mt Base Member Join Date: Aug 2010 Location: East Stroudsburg Pa Posts: 183 Drives: 2010 Z / 2003 G35cp Rep Power: 14	that is the stock oil cooler . couldnt you just unbolt that one and cap off the antifreeze lines and put the thermostatic sandwich plate in its place for the new cooler?

02-08-2014, 08:29 AM	#11 (permalink)
03g35coupe6mt Base Member Join Date: Aug 2010 Location: East Stroudsburg Pa Posts: 183 Drives: 2010 Z / 2003 G35cp Rep Power: 14	well not cap them off i meant more like connect those two lines together dont know i dont have a 2014 i have a 2010 .

02-08-2014, 08:33 AM	#13 (permalink)
helidriver Base Member Join Date: May 2012 Location: The Woodlands, TX Posts: 37 Drives: '12 370Z Sport 6MT Rep Power: 12	Adding oil cooler problem on 2014 The factory size will fit.

02-08-2014, 08:49 AM	#14 (permalink)
03g35coupe6mt Base Member Join Date: Aug 2010 Location: East Stroudsburg Pa Posts: 183 Drives: 2010 Z / 2003 G35cp Rep Power: 14	DIY 2012 25 row Setreb Series 9 Install & stock oil cooler delete

02-08-2014, 10:05 AM	#15 (permalink)
Tigger A True Z Fanatic Join Date: Mar 2013 Location: NM Posts: 8,063 Drives: Awedeeeeee Rep Power: 602	If you value a warranty then do NOT touch the stock oil cooler. Don't mess with it. Don't try to bypass it. Unless of course you bought a brand new car to beat the crap out of at a track. The oil filter size you need is the HP-2008. I used that when I put my sandwich plate on my stock cooler and it fit just fine. So this doesn't turn into another stupid debate over whether you need an extra oil cooler or not, feel free to visit other threads here relating to an aftermarket cooler on top of the stock cooler. You will see plenty of butt-hurt opinions and the like. Take it all with a grain of salt. Bottom line. If you don't track it, don't "NEED" it. But my personal opinion is still quite different from this and I'll leave that out for now. Someone might get their feelings hurt. Good luck to ya! Last edited by Tigger; 02-08-2014 at 10:08 AM.