Is this AAM COMPETITION SHORT TAIL EXHAUST sticking out too much?

YamahaR6 · 02-10-2016, 03:48 PM

Contacted AAM directly, hope they can figure something out.

ZeroZeta · 02-10-2016, 04:14 PM

I had a similar issue but only with one side (driver I believe) was slightly longer than the other side.

I adjusted both tips to make them even. So I have one tip pushed all the way in and the other as far out as it can go.

I might trim the longer side down in the future but overall it looks good. (also seems the same distance from the bumper as yours.)

YamahaR6 · 02-10-2016, 04:28 PM

Thanks for sharing.

Did you contact AAM? Any response from them?

SS_Firehawk · 02-10-2016, 05:01 PM

These tips are generally adjustable. Just move them

YamahaR6 · 02-10-2016, 05:31 PM

I ready adjusted them to the closest to the pipes; but still sticking out.

cooltoy · 02-10-2016, 06:35 PM

Can you dremmel the slots more to allow them to slide back further?

YamahaR6 · 02-10-2016, 09:08 PM

Quote:

Originally Posted by cooltoy

Can you dremmel the slots more to allow them to slide back further?

I would rather not. I just expected it to fit like they advertised.

maro · 02-11-2016, 08:20 PM

Quote:

Originally Posted by 2011 Nismo#91

Nismo tips are just a different diameter from what I understand. The tips are adjustable but they only have so much adjustment, I'm assuming the OP adjusted them back as far as allowed.

That looks perfect to me
I have nismo tips and they look good

Zbrah · 02-11-2016, 09:27 PM

Maybe its further out in real life but from these pictures I don't see it being that bad

Z&I · 02-11-2016, 10:29 PM

You got'em in backwards ...

YamahaR6 · 02-12-2016, 01:42 AM

It doesn't look terrible, but I would prefer it less sticking out.

Contacted AAM and hope they response.

37zeroZ · 02-12-2016, 05:08 PM

Mine are just like yours, 1/2 inch out measured looking straight down from the bumper to the tip. They are a bit further out than stock, but with the burnt tips I like the look.

kenchan · 02-12-2016, 06:34 PM

yah, definitely sticking out too far for my taste too.

the other one on the earlier page is too short. should just get the fujimura cans. that u only need to do minor vertical adjustment.

kenchan · 02-12-2016, 06:37 PM

here.. use this as reference

kenchan · 02-12-2016, 06:38 PM

this is about where mine's at.

02-10-2016, 05:01 PM	#19 (permalink)
SS_Firehawk Premium Member Join Date: Oct 2011 Location: Tampa Posts: 4,142 Drives: 13' Magma Red Nismo Rep Power: 7334	These tips are generally adjustable. Just move them __________________ Old Car:GTM TSC'd 550whp / 410lbft tq @ 11.88PSI New Car: Under Construction

02-10-2016, 06:35 PM	#21 (permalink)
cooltoy Elite Member Join Date: Jun 2012 Location: Calgary Posts: 13,938 Drives: 14 PW 370Z S/T MT Rep Power: 240204	Can you dremmel the slots more to allow them to slide back further? ajm216 likes this. __________________ Member of kenchan's "photoshopped mods" and "proper offsets" gang.

02-11-2016, 09:27 PM	#24 (permalink)
Zbrah A True Z Fanatic Join Date: May 2013 Location: The370Z.com Posts: 4,956 Drives: 370Z Rep Power: 5451	Maybe its further out in real life but from these pictures I don't see it being that bad __________________

02-11-2016, 10:29 PM	#25 (permalink)
Z&I Enthusiast Member Join Date: Feb 2013 Location: New Jersey Posts: 410 Drives: '09 370z 6MT FI Rep Power: 12	You got'em in backwards ... __________________ . BB

02-12-2016, 05:08 PM	#27 (permalink)
37zeroZ Enthusiast Member Join Date: Feb 2010 Location: Dallas Posts: 346 Drives: Truck Rep Power: 14168	Mine are just like yours, 1/2 inch out measured looking straight down from the bumper to the tip. They are a bit further out than stock, but with the burnt tips I like the look. Last edited by 37zeroZ; 02-12-2016 at 05:11 PM.

02-10-2016, 03:48 PM	#16 (permalink)
YamahaR6 Track Member Join Date: Feb 2009 Location: California Posts: 527 Drives: A Car Rep Power: 17	Contacted AAM directly, hope they can figure something out.

02-10-2016, 04:28 PM	#18 (permalink)
YamahaR6 Track Member Join Date: Feb 2009 Location: California Posts: 527 Drives: A Car Rep Power: 17	Thanks for sharing. Did you contact AAM? Any response from them?

02-10-2016, 05:31 PM	#20 (permalink)
YamahaR6 Track Member Join Date: Feb 2009 Location: California Posts: 527 Drives: A Car Rep Power: 17	I ready adjusted them to the closest to the pipes; but still sticking out.

02-12-2016, 01:42 AM	#26 (permalink)
YamahaR6 Track Member Join Date: Feb 2009 Location: California Posts: 527 Drives: A Car Rep Power: 17	It doesn't look terrible, but I would prefer it less sticking out. Contacted AAM and hope they response.

02-12-2016, 06:34 PM	#28 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141520	yah, definitely sticking out too far for my taste too. the other one on the earlier page is too short. should just get the fujimura cans. that u only need to do minor vertical adjustment.

02-12-2016, 06:37 PM	#29 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141520	here.. use this as reference

02-12-2016, 06:38 PM	#30 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141520	this is about where mine's at.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
AAM Competition Short Tail Exhaust DIY	leeyeegue	DIY Section (Do-It-Yourself)	27	08-03-2018 09:08 AM
NEW AAM Competition Short Tail Ti-Tip Exhaust!	Adam@AAMComp	Intake/Exhaust	11	05-16-2012 08:25 AM
NEW AAM Competition Short Tail Ti-Tip Exhaust!	Adam@AAMComp	AAM Competition	3	05-10-2012 02:44 PM
[WTB] AAM Competition S-Line Short Tail Exhaust	shizzl3s	Parts for sale (Private Classifieds)	11	03-09-2012 06:38 PM