Radar Detector Recommendations

Zipper 104

I got my V1 this past summer. It has the JF update. Trust me; it's a noisy b**** even with JF.
Around town YaV1 will emulate Savvy. Savvy lets you set the V1 so you don't get any alerts under any speed you choose. The Savvy module can be purchased from Valentine and plugs into your OBD port. If you run the YaV1 app the software will emulate it so you don't need to buy it.
No. I don't work for, or have anything to do with Valentine. I just did the research before I laid out the coin.
Once again, the site I linked to is all you'll need...and no, I'm not connected to them either.

I'm half thinking of selling my setup. I can't be bothered to put it into the car except on road trips, and since I'm an old fooker I'm really careful where I do speed. And for me, speeding is 20 over, tops. Not like when I was a lead footed young'un.

104

jcosta79

Are you running in full Logic mode?

Sent from my Nexus 7 using Tapatalk

__________________
2012 PW NISMO #0559 - GT Spec Brace Kit - Swift Springs - ARK TP & Invidia CBE K&N Intake - UpRev Tune - 15mm Z1 Spacers & Studs - StopTech Slotted Rotors & SS Lines - ZSpeed CMAK with Stage 2 Clutch and Lightweight Flywheel

Hemingway

Valentine1 and Waze

Zipper 104

I wouldn't even know how to dial up logic mode. I have always run it through YaV1.....every second I've used it. LM is something in V1 and not YaV1, right?

I must look in the manual and see how it's done. I'm really not all that familiar with the controls on the V1. I never use 'em except to turn it on. YaV1 has a mode where the display on the V1 is black so it doesn't light up like a christmas tree at night. YaV1 runs on the phone down low in the car. All the alerts go there.

104

VABAM

Using the on board buttons to change modes on a V1 is a PITA. I use the bluetooth dongle and V1s iPhone app to switch modes.

BTW you can use a splitter like this one, RJ11 Splitter, to run the bluetooth dongle and the remote screen at the same time on a V1.

__________________

jcosta79

That's why you get so many false alarms. None of the filters are working unless you turn on full Logic mode. Push the power button until you get a small "L". Then push it again until you get a large " L". That's full Logic mode. Filters out all the false alarms. V1 in unfiltered mode is unbearable. You will fall in love with the V1 once you use it properly and enable full Logic filtering.

Edit: You only have to do this ONCE. It will turn on in full Logic mode every time after you do it one time.

Sent from my Nexus 7 using Tapatalk

__________________
2012 PW NISMO #0559 - GT Spec Brace Kit - Swift Springs - ARK TP & Invidia CBE K&N Intake - UpRev Tune - 15mm Z1 Spacers & Studs - StopTech Slotted Rotors & SS Lines - ZSpeed CMAK with Stage 2 Clutch and Lightweight Flywheel

Zipper 104

I put my V1 in the car today for the first time in ages. I looked at the manual last night to see how to switch modes. Today I ran the V1 without the phone and YaV1 and the only thing that showed when I switched modes was a large U and a small u. Then I remembered that YaV1 reprograms the V1 so I figured I'd have to link to the phone again and change things to get the V1 back in its normal state and get those logic modes. I'll try it again tomorrow for the h*** of it.

104