Z&I

Hi NYC Z34 ...
Happy to try to help ...
Here's my email address:
bobgallagherfoto@aol.com
Much easier to communicate that way.
I will have a copy your message waiting to answer you.
It is much easier to correspond that way.
Read all 101 pages ??? wow ;-)
The thread was started by TopGunZ ... and he was able to successfully get his project done, but he has engineering and manufacturing experience under his belt.
Just a few things to send in your email:
Miles on the car - miles on the Stillen kit
History of the Stillen install and maintenance including check for Boost leaks
Stock motor ? Stock Stillen Tune ? Dyno ?
The stock Stillen set up with their canned UpRev tune generally produces about 415 whp provided the installation was done correctly.
Can't really recommend any shops for you - everyone is an expert until they run in to problems...found that out the hard way.
You can try to contact Stillen to see if they have any authorized or recommended shops in our area.
Looking forward to hear from you...
Bob

Hey Z&I,
I just joined the Z club and wanted reach out to you regarding performance shop question, i just finished reading all 101 pages of Jwllis saga on his car and you seemed to be a knowledgeable person, i am in the Rockland NY area and was wondering if you could point me in a good direction with a performance shop in NJ? i have an 09 Z with a Stillen SC, Stillen Headers and Berk test pipes. Bought the car from a dealer like this, so i wanna Dyno and see what going on with the car. It runs now, the prosport air/fuel gauge is making a alarm sound when i get on it, everything seems fine to me though, but i am a newbie. Any help will help. THX

Hey! Sorry I don't get notifications from your wall lol..I'm 5 min from the GWB as well...we'll start doing some once its starts getting warmer out...this is the thread where we organize http://www.the370z.com/north-east-re...thread-85.html

Where and When ?
I'm only a few miles from the GW Bridge
Bob

Hey u see ur from jersey too, u should check out the north jersey meet thread

I made a new bracket on our cnc machine. Made it out of 7075 al. That grade is twice as strong as 6061 and tge stillen one could be made of even a lower grade. Didn't cut the bolt slot out. So this...

So it works absolutely perfect! I decided to mount the corner bracket like stillen did. I used 2 random nuts from my shops junk bin. This should Add some more strength in that area. I'm going to...

my buddy did it for me for a case of beer at his cnc shop. :)

About everything you just mention but add at least another 5-8k for if and when the motor goes boom. Also the tuning is very important!

Assume $15k minimum, more like $20k, and then an additional $5-8k for the I popped my motor fund.

Update - Sasha made some good ground last night! He ditched the 2.5" intake into the blower, Built a 3" pipe into the blower, routed the filter down in front of the drivers front wheel. He...

EDIT: (Revised for 2018, current with my experiences since originally commenting) The ideal and proper way, is probably more commitment to drag racing than most Z owners are looking for. Small...

I have never seen or heard of a copper cooler. They may exist and yes copper has better heat transfer rate. Its probably a cost thing. It would be insanely expensive to manufacture vs aluminum. Water...

BTW: I found this http://www.the370z.com/attachment.php?attachmentid=104740&stc=1&d=1435110674 http://www.the370z.com/attachment.php?attachmentid=104741&stc=1&d=1435110678

Yes but even if that front mount was the size of the whole bumper itself it wouldn't be able to handle the heat generated at 10+ psi. It ALL still has to go through the 3 whole inches of aftercooler...

If ambient is 23 you will never get it below that unless using ice to drop it to 10-15 degrees. I have done tons of research regarding water vs air and basically water is king, but ONLY on the...

you would have to use a Aftermarket IAT sensor and would have to be mounted in the intake manifold under the intercooler. that's the only way for it work. Its really hard to read what our air...

So since Stillen is the only SC available for the 370z family, I have been looking at how to get this kit up to snub to take on more horsepower at safer operation and reliability to the engine. ...

There is no dry carbon fiber vented hood out there that I know of. That's precisely the reason I bought a spare oem hood and modified it. Lighter than any vented hood on the nsrket Sent from my...

At the risk of feeding the trolls, I have to respond. First, I don't know why you even bring up gtm in this thread. It's uncalled for and frankly, pointless. I don't think Tony and Dan have ever...