Nissan 370Z Forum

370Z Forums HOME

My Picture Album

Nissan 370Z Pictures

Premium Membership

Become a Forum Sponsor

		Nissan 370Z Forum > Members List
StrokeThis347's Profile

StrokeThis347 is on a distinguished road

StrokeThis347

Base Member

Statistics

Total Posts

Total Posts: 65
Posts Per Day: 0.02
Find all posts by StrokeThis347
Find all threads started by StrokeThis347

General Information

Join Date: 03-25-2013
Referrals: 0

Likes Received

12 Likes

DiegoZ liked post by StrokeThis347 On thread : AAM Short Tails

.
Liked On: 01-13-2015, 12:23 PM
Posted On: 12-18-2014, 12:35 PM
luigi90210 liked post by StrokeThis347 On thread : Sticky: (Official) 370Z Clutch Pressure (CSC) Failures

Just to confirm Nissan did recently release a TSB stating to use GTR brake fluid to cure/avoid this problem. Source: Nissan/Infinity Master Tech
Liked On: 08-08-2013, 12:27 AM
Posted On: 03-27-2013, 11:02 PM
ChrisSlicks liked post by StrokeThis347 On thread : Is this normal oil consumption?

Trust me change it at 100. All of those metal shavings, any dirt that fell in, lint from wiping parts ext will clog up that oil filter in no time and you will be running in bypass let anymore crud...
Liked On: 05-06-2013, 05:45 PM
Posted On: 04-04-2013, 01:21 PM
marty31 liked post by StrokeThis347 On thread : Is this good dyno numbers?

For the amount of time your at this speed tire temps are not even a consideration. Of course your differential is not 1:1, you just want a direct drive or as close as possible through your...
Liked On: 05-01-2013, 12:30 PM
Posted On: 04-22-2013, 07:02 PM
370ZNISMO#704 liked post by StrokeThis347 On thread : Is this good dyno numbers?

You want to dyno in a 1:1 gear so 5th. I would also be curious if they even used a correction factor.
Liked On: 04-29-2013, 11:19 PM
Posted On: 04-14-2013, 09:15 PM
tower74 liked post by StrokeThis347 On thread : Ring Seating on Break-in... How long?

I am an engine builder. As you said the biggest thing is keeping the engine from sitting at a constant rpm too long. You do not need to worry about constantly keeping it loaded. Rings usually seat...
Liked On: 04-28-2013, 04:03 PM
Posted On: 04-25-2013, 09:58 PM
tower74 liked post by StrokeThis347 On thread : Ring Seating on Break-in... How long?

However, even on new engines keeping the engine at a constant rpm during the break in period will glaze over the cylinder walls and the rings will not fully seat.
Liked On: 04-28-2013, 04:03 PM
Posted On: 04-25-2013, 10:06 PM
Rusty liked post by StrokeThis347 On thread : Is this normal oil consumption?

Trust me change it at 100. All of those metal shavings, any dirt that fell in, lint from wiping parts ext will clog up that oil filter in no time and you will be running in bypass let anymore crud...
Liked On: 04-04-2013, 08:59 PM
Posted On: 04-04-2013, 01:21 PM
Rusty liked post by StrokeThis347 On thread : Is this normal oil consumption?

I would change it in 100 miles, then 1000. Do this to get any dirt or crud that may have gotten into the engine when it was open and they were working on it.
Liked On: 04-04-2013, 08:57 PM
Posted On: 04-03-2013, 10:17 PM
avantgti7 liked post by StrokeThis347 On thread : Is this normal oil consumption?

I would change it in 100 miles, then 1000. Do this to get any dirt or crud that may have gotten into the engine when it was open and they were working on it.
Liked On: 04-04-2013, 07:23 AM
Posted On: 04-03-2013, 10:17 PM
SouthArk370Z liked post by StrokeThis347 On thread : Is this normal oil consumption?

I would change it in 100 miles, then 1000. Do this to get any dirt or crud that may have gotten into the engine when it was open and they were working on it.
Liked On: 04-03-2013, 10:34 PM
Posted On: 04-03-2013, 10:17 PM
Initial Z liked post by StrokeThis347 On thread : Clutch fluid flush

I would have to look but my guess is 30k when the brake fluid is supposed to be changed.
Liked On: 03-30-2013, 10:28 PM
Posted On: 03-30-2013, 06:40 PM

Mini Statistics

Join Date: 03-25-2013
Total Posts: 65
Likes Received: 12
Likes Given: 1

Show All Statistics

All times are GMT -5. The time now is 09:00 AM.