k67p67

Enthusiast Member

Last Activity: Today 10:27 AM

Statistics

Total Posts

Total Posts: 313
Posts Per Day: 0.10
Find all posts by k67p67
Find all threads started by k67p67

Albums

Total Albums: 1
Total Pictures: 5
Albums Created by k67p67

General Information

Last Activity: Today 10:27 AM
Join Date: 10-01-2016
Referrals: 0

Friends

Showing Friends 1 to 3 of 3

cigarclifford

A True Z Fanatic
Dreadnaught

Track Member
KapitalZ

Base Member

Likes Received

252 Likes

God-Speed liked post by k67p67 On thread : What Exhaust Is This?

It all depends on what your goals are. Are you just looking to add some growl to your Z? Do you intend to autox or track the car? I/H/E has always been a common starting point for mods. Although, the...
Liked On: 03-24-2023, 06:20 AM
Posted On: 03-23-2023, 05:16 PM
Will 370Z liked post by k67p67 On thread : What Exhaust Is This?

Looks like Beluga Racing https://belugaracing.com/wp-content/uploads/2017/07/IMG_2157-scaled.jpg
Liked On: 03-23-2023, 09:07 AM
Posted On: 03-22-2023, 07:20 PM
Lazy Vic liked post by k67p67 On thread : Z1 s pro coilover noise

Did you reuse the stock lower rubber mounts inside the spring buckets?
Liked On: 02-20-2023, 05:26 PM
Posted On: 02-09-2023, 06:17 PM
$ully liked post by k67p67 On thread : DIY Yaw Sensor rocker switch

Black = ground Red = 12V+ parking lights Yellow = 12V+/Switched Ignition/Accessory depending on what your plans are for the switch. You can find a switched ignition source if you are using it to...
Liked On: 11-02-2022, 01:50 PM
Posted On: 09-18-2021, 09:00 PM
Spunk liked post by k67p67 On thread : The "Will it fit?" thread

I doubt the 18x10.5 will clear the Akebonos. Caliper clearance is dependent upon pad size, barrel diameter, spoke articulation. Both of the offset sizes offered only come in Weds' RR face which is...
Liked On: 07-09-2022, 08:39 PM
Posted On: 07-05-2022, 10:10 PM
Spunk liked post by k67p67 On thread : The "Will it fit?" thread

Well, there's your answer. I stand corrected. The 18" RR face will accommodate the Akebonos. Good looking out OZ!
Liked On: 07-09-2022, 08:39 PM
Posted On: 07-06-2022, 07:04 PM
cv129 liked post by k67p67 On thread : Are these spacers any good?

The length of the OEM studs is greater than the thickness of your spacer. Therefore, a portion of the stud will protrude beyond the mounting surface of the spacer. This is a typical 20mm bolt-on...
Liked On: 06-23-2022, 09:43 AM
Posted On: 06-22-2022, 05:43 PM
JARblue liked post by k67p67 On thread : Are these spacers any good?

The length of the OEM studs is greater than the thickness of your spacer. Therefore, a portion of the stud will protrude beyond the mounting surface of the spacer. This is a typical 20mm bolt-on...
Liked On: 06-23-2022, 09:29 AM
Posted On: 06-22-2022, 05:43 PM
Memphis370Z liked post by k67p67 On thread : Are these spacers any good?

The length of the OEM studs is greater than the thickness of your spacer. Therefore, a portion of the stud will protrude beyond the mounting surface of the spacer. This is a typical 20mm bolt-on...
Liked On: 06-22-2022, 05:53 PM
Posted On: 06-22-2022, 05:43 PM
R1talin liked post by k67p67 On thread : ALL blinkers hyperblink?

Check both your front and rear turn signal bulbs. If they are LED bulbs, insert the appropriate value resistors and problem solved.
Liked On: 05-26-2022, 06:46 PM
Posted On: 05-25-2022, 07:09 PM
cv129 liked post by k67p67 On thread : ALL blinkers hyperblink?

What are the specs on the resistors that your removed from the front turn signal wiring? How did you wire them? They need to be configured as a load across the positive and ground wires.
Liked On: 05-26-2022, 05:00 PM
Posted On: 05-26-2022, 02:50 PM
cv129 liked post by k67p67 On thread : ALL blinkers hyperblink?

Check both your front and rear turn signal bulbs. If they are LED bulbs, insert the appropriate value resistors and problem solved.
Liked On: 05-26-2022, 12:02 AM
Posted On: 05-25-2022, 07:09 PM
SeeThruHead liked post by k67p67 On thread : ALL blinkers hyperblink?

Check both your front and rear turn signal bulbs. If they are LED bulbs, insert the appropriate value resistors and problem solved.
Liked On: 05-25-2022, 08:35 PM
Posted On: 05-25-2022, 07:09 PM
sx moneypit liked post by k67p67 On thread : The "Will it fit?" thread

You cannot achieve flush fitment by changing tire sizes. Flush fitment is determined by wheel width, offset, and alignment. Since new wheels aren't currently in you budget, you'll have to use spacers...
Liked On: 05-11-2022, 06:58 AM
Posted On: 05-10-2022, 02:37 PM
cv129 liked post by k67p67 On thread : What did you do with your Z today V (ON TOPIC DISCUSSION ONLY)

-2.0 degrees camber will only add very minimal additional wear as long as toe is kept in check. Your -1.5 degrees camber is essentially at the edge of factory spec. So, if you experienced premature...
Liked On: 04-21-2022, 11:13 AM
Posted On: 04-20-2022, 06:45 PM

Page 4 of 17

« First

Last »

k67p67

Enthusiast Member

Statistics

Friends

Likes Received

Mini Statistics

Friends

Albums

Recent Visitors

	cigarclifford A True Z Fanatic

	Dreadnaught Track Member

	KapitalZ Base Member