Neck and neck then. I just need to borrow your talent in the car? :icon17:

I wish you could of made it? But work is work.

yeah, it really sucked. Even though I was only going to bring Teresa's Z4. Really curious as to what it would have pulled.

Then take it to the track. :bowrofl:

Nice numbers spohn glad you got it on the dyno! I've been fallowing your thread for awhile now. I also liked your roll cage!

Thanks. Keep checking in from time to time in the next week or so. I have a lot of goodies coming in.

Z1 PCV hoses
 

http://i1109.photobucket.com/albums/...Day2012025.jpg

http://i1109.photobucket.com/albums/...Day2012026.jpg

Looking great SPOHN!!!

:iagree:

Looks great. rep to you sir.

Loving the silicone! :yum:

Can I ask what's up with the manifold cover?

Yea, it's not there.:icon17: It traps heat IMO so I remove along with all the other plastic trim in the bay.

Your Azz traps heat :icon23::icon17:

Especially after the cheddar brats I had.

:drool::drool::drool:

Ah yeah, gotcha! Makes perfect sense! :tup:

I removed my manifold cover also, but ended up putting back the other two covers over the little corner compartments. On the battery side, I've got my catch can in there, so I figure keeping it colder helps condensation. If you actually had a battery there I'd say keep it for that too, but I think you already relocated that, right?

On the brakes side, I figure keeping engine bay heat off the brake fluid reservoir can't hurt, but now I'm not so sure which way is better tbh. I guess the missing data is I'm not sure, when the fluid is hot, how far up the brake system the fluid heat travels (or how much difference cooler fluid at the top of the system can make). My suspicion is that the brake fluid stays slightly cooler with the reservoir insulated from the bay though.

Stillen Brake Cooling Kit
 

Just got here. The quality of this kit is very good. Very happy with it. Can't wait to get it on.

http://i1109.photobucket.com/albums/...goodies001.jpg

http://i1109.photobucket.com/albums/...goodies002.jpg

http://i1109.photobucket.com/albums/...goodies003.jpg

http://i1109.photobucket.com/albums/...goodies004.jpg

^Very nice^ looking forward to installed pics!

:iagree:

:iagree: X2

very nice sir!

Lip Lip where is the Lip!!!!!:icon17:

Trying to get it done. Need to find a good way to bolt inside the fenders without affecting the wheel wells.

Just use small screws

Seems like there going to go threw the plastic wheel well being it's tuck into the inside lip of the OEM front clip. I want to make sure I don't have to unbolt it everytime I remove it. BUt I haven't really looked at it. I just quickly glanced at it for a moment

Nice so far spohn! Can't wait to see installed pics and pics of the new lip kit!

where did you get your roll cage made at?!

At Forged Performance here in GA. One of the few that can do it all in house.

May is ask for an estimate of how much it ran you ? Its fine if you don't wanna tell me haha

Got the most out of these Carbotech XP8's. There some more life left but not for the track.

http://i1109.photobucket.com/albums/...lingKit009.jpg

http://i1109.photobucket.com/albums/...lingKit010.jpg

Body Transformation
 

Well after two hard long days I got all my body mods on the car. It looks killer IMO. It really sets it of. Especially the black. It gives the car a better contrast. Course hard to tell from my crap camera.

But below you will see the Shine Auto Spec S kit, Stillen Canards, and the super sexy Carbon Signal Hood Vents that I had molded in. Boy they look killer. I bought the Shine kit in FRP and I plasti dipped it. :icon17: I went this route being I track my car a bit and I felt this was a great alternative than expensive paint that would get tore up my first day out which is coming soon enough. I can easily repair or redo on the fly with plasti dipped. Which has already shown me from three track days that it's very durable.

I also added the Stillen front canards for some front downforce for some extra bit threw the turns. Especially any off camber turns. As far as the rear I'm not sure what I'm going to add back there. I've been holding out for something that really grabs my attention.

Then finally the Carbon Signal Hood Vents. I'm so glad I got these. They are sharp as hell. Many props to the guys at AutoGlo. I know it had to be a pain to do but I'm happy to sport this rare piece. It sets it off in a good aggressive way. So hope you like and enjoy.



http://i1109.photobucket.com/albums/...akeover040.jpg
http://i1109.photobucket.com/albums/...akeover013.jpg
http://i1109.photobucket.com/albums/...akeover024.jpg
http://i1109.photobucket.com/albums/...akeover030.jpg
http://i1109.photobucket.com/albums/...akeover031.jpg
http://i1109.photobucket.com/albums/...akeover028.jpg
http://i1109.photobucket.com/albums/...akeover017.jpg
http://i1109.photobucket.com/albums/...akeover010.jpg
http://i1109.photobucket.com/albums/...akeover041.jpg
http://i1109.photobucket.com/albums/...akeover044.jpg
http://i1109.photobucket.com/albums/...akeover026.jpg
http://i1109.photobucket.com/albums/...akeover023.jpg
http://i1109.photobucket.com/albums/...akeover026.jpg
http://i1109.photobucket.com/albums/...akeover010.jpg
http://i1109.photobucket.com/albums/...akeover018.jpg
http://i1109.photobucket.com/albums/...akeover021.jpg

Looks good Chris I thought you did the back bumper like mine.

No. I might end up doing that afterall until something else comes out. There only 200 bucks. It will give it a well rounded look.

Looking awesome Spohn. Love the hood. Car is looking badazz. How has it been treating you on the track?? Also, how do you like the Stillen brake cooling kit?? You are the first member I have seen install this.

Thanks man. The car is great on the track. No issues yet. The Stillen kit is great. Course I haven't had a chance to use it yet. But I will at the end of the month. Need to get a pyrometer though. I still need to install my GTM diff cooler kit also.

Mr. Spohn,

Your Z looks like one bad mamma-jamma.

That's all.

onzedge has written

My gawd that hood....I say it again, that hood! So badazz! Nice job man! :tup:

Wicked! Looks sharp!

Oh yeah, damn nice Spohn!!!