The New "What did you do with your Z today" (with off topic replies) XXIV

ChaseZ · 08-11-2016, 12:36 PM

Had some of the high temp ceramic coating leftover that I didn't use, so baking the strut bar in place. I like the sort of raw steel look.. undecided if I'll add back my Motordyne decal on it but probably.

Masterbeatty · 08-11-2016, 12:41 PM

Quote:

Originally Posted by ChaseZ

Had some of the high temp ceramic coating leftover that I didn't use, so baking the strut bar in place. I like the sort of raw steel look.. undecided if I'll add back my Motordyne decal on it but probably.

Looks good.

I need to re- clear my engine cover. For some reason it's all scalely and rough so the Carbon does not look nice at all.

ChaseZ · 08-11-2016, 12:45 PM

Quote:

Originally Posted by Masterbeatty

Looks good.

I need to re- clear my engine cover. For some reason it's all scalely and rough so the Carbon does not look nice at all.

I like the CF engine covers but too much $$$ for me

Was thinking of CF cover for my shifter ring to tie in with my add on spoiler and minimalist front lip, but having a hard time justifying $189 for it

Don't want too much CF but those few subtle touches I think are nice.

madwi · 08-11-2016, 06:05 PM

Quote:

Originally Posted by ChaseZ

I like the CF engine covers but too much $$$ for me

Was thinking of CF cover for my shifter ring to tie in with my add on spoiler and minimalist front lip, but having a hard time justifying $189 for it

Don't want too much CF but those few subtle touches I think are nice.

I am going to have to bust out the dremel if I want my cover back on.

ChaseZ · 08-11-2016, 06:08 PM

Quote:

Originally Posted by madwi

I am going to have to bust out the dremel if I want my cover back on.

Uh oh don't like the sounds of this..!

madwi · 08-11-2016, 06:10 PM

Quote:

Originally Posted by ChaseZ

Uh oh don't like the sounds of this..!

I think it will be OK if I plan it right. Where the nitrous and fuel lines connect to the plate is right in the way of the corner/side of the engine cover. Shouldn't be too bad to make a decent looking notch.

ChaseZ · 08-11-2016, 06:15 PM

Quote:

Originally Posted by madwi

I think it will be OK if I plan it right. Where the nitrous and fuel lines connect to the plate is right in the way of the corner/side of the engine cover. Shouldn't be too bad to make a decent looking notch.

Ah I see where you're going with this. Yeah a steady hand and some patience should do a nice clean job. Maybe make a guide if possible.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The New "What did you do with your Z today" (with off topic replies) XXIII	eastwest2300	The Lounge (Off Topic)	10001	06-23-2016 09:21 AM
The New "What did you do with your Z today" (with off topic replies) XXII	eastwest2300	The Lounge (Off Topic)	10001	04-05-2016 08:15 PM
The New "What did you do with your Z today" (with off topic replies) XVIV	eastwest2300	The Lounge (Off Topic)	10005	09-11-2015 08:57 AM
The New "What did you do with your Z today" (with off topic replies) XVIII	eastwest2300	The Lounge (Off Topic)	10000	07-09-2015 07:48 PM
The New "What did you do with your Z today" (with off topic replies) XIII	JARblue	The Lounge (Off Topic)	10011	08-04-2014 04:16 PM

08-11-2016, 12:36 PM	#1 (permalink)
ChaseZ A True Z Fanatic Join Date: May 2016 Location: Calgary Posts: 3,799 Drives: 16 370z Rep Power: 94685	Had some of the high temp ceramic coating leftover that I didn't use, so baking the strut bar in place. I like the sort of raw steel look.. undecided if I'll add back my Motordyne decal on it but probably.