Jenvey on throttle-Body selection

BGTV8 · 01-27-2014, 10:53 PM

I'm deep into the bowels of a 3.7/3.8 litre VQ35HR engine component specification based off the Grand Am engine-spec and am now looking at ITB set-up and found this article on an AU site ....

Contains some interesting background ... and worth reading, if only for general knowledge/background.

Throttle Body Selection with Jenvey Dynamics

RB

Kingbaby · 01-27-2014, 11:11 PM

brains hurts on trying to comprehend the awesome that goes into ITBs

can't wait till the VQ and it's many chassis are under 20k range so aftermarket can pick up!

Jordo! · 01-28-2014, 02:01 AM

I didn't think you could run ITB's without losing the VVEL.

BGTV8 · 01-28-2014, 02:31 AM

Plan is to use the Grand Am HR head conversion, in fact I'll probably lose the exhaust cam phasing as well

Remember, the objective is a 500hp at 9000 rpm, full-race engine, not a modded road engine, and IMHO, VVEL is too complicated to use in a race engine, but that is another issue.

RB

Jordo! · 01-28-2014, 03:03 AM

Oh, wow -- well if that's your aim, then, sure -- go for it! For a build like this ditching the OEM head is definitely the way to go.

Are you planning to run the ITB's open or are you going to design a plenum to house?

What you using to tune -- motec?

BGTV8 · 01-28-2014, 03:10 AM

I'm expecting to run a pair of plenum;s - final design not yet settled, but will be at least 9 litres of air-box volume per bank

Engine management will be Motec (Motec research are scheduled to have a VQ engine on the dyno early in Feb).

I already have a Holinger 6-speed sequential and the diff, the donor VQ35HR should arrive shortly (purchased in the US and being shipped back to the engine-builder in Adelaide), and parts purchases are scheduled out to August.

All going to plan, the engine should run early next year (our race season starts in Feb and runs thru to Nov). Chassis prep will start once the engine parts purchases are completed.

01-27-2014, 10:53 PM	#1 (permalink)
BGTV8 A True Z Fanatic Join Date: Dec 2009 Location: 03350 Australia Posts: 1,516 Drives: 09 Nissan 370Z M6 Rep Power: 39974	Jenvey on throttle-Body selection I'm deep into the bowels of a 3.7/3.8 litre VQ35HR engine component specification based off the Grand Am engine-spec and am now looking at ITB set-up and found this article on an AU site .... Contains some interesting background ... and worth reading, if only for general knowledge/background. Throttle Body Selection with Jenvey Dynamics RB

01-28-2014, 02:01 AM	#3 (permalink)
Jordo! A True Z Fanatic Join Date: May 2010 Location: nirvana Posts: 6,394 Drives: 2023 NATM Rep Power: 419	I didn't think you could run ITB's without losing the VVEL. __________________ Enjoy it. Destroy it.

01-28-2014, 03:03 AM	#5 (permalink)
Jordo! A True Z Fanatic Join Date: May 2010 Location: nirvana Posts: 6,394 Drives: 2023 NATM Rep Power: 419	Oh, wow -- well if that's your aim, then, sure -- go for it! For a build like this ditching the OEM head is definitely the way to go. Are you planning to run the ITB's open or are you going to design a plenum to house? What you using to tune -- motec? __________________ Enjoy it. Destroy it.

01-28-2014, 03:10 AM	#6 (permalink)
BGTV8 A True Z Fanatic Join Date: Dec 2009 Location: 03350 Australia Posts: 1,516 Drives: 09 Nissan 370Z M6 Rep Power: 39974	I'm expecting to run a pair of plenum;s - final design not yet settled, but will be at least 9 litres of air-box volume per bank Engine management will be Motec (Motec research are scheduled to have a VQ engine on the dyno early in Feb). I already have a Holinger 6-speed sequential and the diff, the donor VQ35HR should arrive shortly (purchased in the US and being shipped back to the engine-builder in Adelaide), and parts purchases are scheduled out to August. All going to plan, the engine should run early next year (our race season starts in Feb and runs thru to Nov). Chassis prep will start once the engine parts purchases are completed. Jordo! likes this.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

01-28-2014, 02:31 AM	#4 (permalink)
BGTV8 A True Z Fanatic Join Date: Dec 2009 Location: 03350 Australia Posts: 1,516 Drives: 09 Nissan 370Z M6 Rep Power: 39974	Plan is to use the Grand Am HR head conversion, in fact I'll probably lose the exhaust cam phasing as well Remember, the objective is a 500hp at 9000 rpm, full-race engine, not a modded road engine, and IMHO, VVEL is too complicated to use in a race engine, but that is another issue. RB

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Throttle body ???	ScotyBRAVO	Intake/Exhaust	18	06-25-2013 06:38 AM
throttle body screw!!	Red_Z	Engine & Drivetrain	9	02-27-2013 11:37 AM
Throttle Body	Fabsnoop	Engine & Drivetrain	1	09-15-2010 02:19 AM
Throttle body warmer. .	soaka1	Engine & Drivetrain	3	08-18-2009 01:32 PM
Impul Throttle Body Kit, Anyone Here Have It?	nightfire	Engine & Drivetrain	4	07-23-2009 08:36 PM