R2C intake discussion ...

Methodical4u · 10-05-2011, 02:31 AM

Ok guys, so i've been debating for quite a while about which intakes to go with. Obviously most use the G3's which have the biggest power gain that is shown so far.

The problem here is that the R2C's have never been dyno'd.

For those who are running the this set-up, did you feel a power difference?

For those who are into the mechanical details the G37's run these and the power gain with them vs. the G3's are basically the exact same. The G37 has a more open front end from what I remember seeing anyway... so it would make sense that the higher air flow causes more of a power gain.

How many would think that if these gains are proven on the 37's that on the Z's it would produce similar gains? Does anyone know if the other intake systems produce similar gains on the G37 vs. the Z?

I may get these and get a before and after dyno to put this to rest, but it's expensive if it doesn't end up being much of a power gain.

XwChriswX · 10-05-2011, 08:59 PM

It will be less expensive than the Top Speed intakes.

I too looked at these and

over them. (Especially in the gloss black coating

) but couldn't justify replacing the stock air box with another air box. However I don't think the loss of power vs the Gen III's will be that tremendous.

However I will let you know there are 3 companies that are making intakes for the Z that should be rolling out very soon, if you can hold on just a little longer.

Methodical4u · 10-05-2011, 09:04 PM

Quote:

Originally Posted by XwChriswX

It will be less expensive than the Top Speed intakes.

I too looked at these and

over them. (Especially in the gloss black coating

) but couldn't justify replacing the stock air box with another air box. However I don't think the loss of power vs the Gen III's will be that tremendous.

However I will let you know there are 3 companies that are making intakes for the Z that should be rolling out very soon, if you can hold on just a little longer.

ahhh man, don't hold out on me lol.

DarkZide · 10-05-2011, 09:23 PM

on an N/A motor the amount of air near the intake isn't really a huge factor (unless there is just simply no air). Ram air setups and similar stuff make little to no difference, so there is probably minimal difference in here either.

The big difference, if any, probably comes from the air being somewhat cooler where the G3 filters are verses right inside the engine bay like the R2C.

Anyway, its still 500$ for these short ram intakes....how is it that people dont see how extemely overpriced parts are for these cars? Its a cheap metal pipe with a MAF mount welded on. Woopty do!

FL 4Motion · 10-05-2011, 11:39 PM

Quote:

Originally Posted by XwChriswX

It will be less expensive than the Top Speed intakes.

I too looked at these and

over them. (Especially in the gloss black coating

) but couldn't justify replacing the stock air box with another air box. However I don't think the loss of power vs the Gen III's will be that tremendous.

However I will let you know there are 3 companies that are making intakes for the Z that should be rolling out very soon, if you can hold on just a little longer.

/\ spill it!

Methodical4u · 10-06-2011, 05:02 PM

Quote:

Originally Posted by DarkZide

on an N/A motor the amount of air near the intake isn't really a huge factor (unless there is just simply no air). Ram air setups and similar stuff make little to no difference, so there is probably minimal difference in here either.

The big difference, if any, probably comes from the air being somewhat cooler where the G3 filters are verses right inside the engine bay like the R2C.

Anyway, its still 500$ for these short ram intakes....how is it that people dont see how extemely overpriced parts are for these cars? Its a cheap metal pipe with a MAF mount welded on. Woopty do!

I can agree with a lot of what you are saying, but the R2C's look like a top quality set-up. If they were just another SRI, it wouldn't have almost exactly the same numbers as the Stillen's which are also over 500.00 on the G37 dynos.

RCZ · 10-06-2011, 05:26 PM

I'd wait for someone to be selling a set of G3's...

Nikkolai · 10-06-2011, 05:35 PM

Or perhaps the Takeda long tube filters that do not require any cutting.

Methodical4u · 10-06-2011, 05:46 PM

Quote:

Originally Posted by Nikkolai

Or perhaps the Takeda long tube filters that do not require any cutting.

I only saw those for the G37's... unless they are coming out for the Z as well.

Nikkolai · 10-06-2011, 05:48 PM

Quote:

Originally Posted by Methodical4u

I only saw those for the G37's... unless they are coming out for the Z as well.

I forgot who mentioned it but they are close to releasing that system on the 370Z. Maybe it was one of the three intakes coming out soon, lol.

Methodical4u · 10-06-2011, 05:49 PM

Quote:

Originally Posted by Nikkolai

I forgot who mentioned it but they are close to releasing that system on the 370Z.

that's a possibility as well then.

Methodical4u · 10-07-2011, 02:04 PM

damnit Chris!!! We need some info!

XwChriswX · 10-09-2011, 10:41 PM

daisuke149 · 10-09-2011, 10:51 PM

Quote:

Originally Posted by XwChriswX

Chris will lose his tescicles if he spills. Even though they are only being used by himself, im sure he wants to hang on to them.

Trips · 10-09-2011, 10:55 PM

Quote:

Originally Posted by daisuke149

Chris will lose his tescicles if he spills. Even though they are only being used by himself, im sure he wants to hang on to them.

Not Necessary in the Tech Section

10-05-2011, 02:31 AM	#1 (permalink)
Methodical4u A True Z Fanatic Join Date: Jun 2011 Location: Maryland Posts: 1,393 Drives: 11 370 6mt pw w/sp Rep Power: 15	R2C intake discussion ... Ok guys, so i've been debating for quite a while about which intakes to go with. Obviously most use the G3's which have the biggest power gain that is shown so far. The problem here is that the R2C's have never been dyno'd. For those who are running the this set-up, did you feel a power difference? For those who are into the mechanical details the G37's run these and the power gain with them vs. the G3's are basically the exact same. The G37 has a more open front end from what I remember seeing anyway... so it would make sense that the higher air flow causes more of a power gain. How many would think that if these gains are proven on the 37's that on the Z's it would produce similar gains? Does anyone know if the other intake systems produce similar gains on the G37 vs. the Z? I may get these and get a before and after dyno to put this to rest, but it's expensive if it doesn't end up being much of a power gain.

10-05-2011, 08:59 PM	#2 (permalink)
XwChriswX WFLYIDNNE Join Date: Jul 2009 Location: In The Fastlane Posts: 50,648 Drives: 02 GDB WRX Rep Power: 451	It will be less expensive than the Top Speed intakes. I too looked at these and over them. (Especially in the gloss black coating ) but couldn't justify replacing the stock air box with another air box. However I don't think the loss of power vs the Gen III's will be that tremendous. However I will let you know there are 3 companies that are making intakes for the Z that should be rolling out very soon, if you can hold on just a little longer. __________________ Bonnie - Stage 2, Audio build coming this fall! R.I.P. Abby 3/29/10 - 3/30/14

10-09-2011, 10:41 PM	#13 (permalink)
XwChriswX WFLYIDNNE Join Date: Jul 2009 Location: In The Fastlane Posts: 50,648 Drives: 02 GDB WRX Rep Power: 451	__________________ Bonnie - Stage 2, Audio build coming this fall! R.I.P. Abby 3/29/10 - 3/30/14

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wheel Offset Discussion Thread... How far can we go?	bullitt5897	Wheels & Tires	393	10-21-2019 01:33 PM
Price discussion....Military program	krnbbagadog	Nissan 370Z Pricing / Ordering Discussions	11	02-19-2011 11:44 AM
Peak Power discussion...	klubbheads	Engine & Drivetrain	4	02-19-2009 08:52 PM
Discussion Thread: 370z pictures from Europe 11.05.08	AK370Z	Nissan 370Z General Discussions	17	11-09-2008 04:04 PM

10-05-2011, 09:23 PM	#4 (permalink)
DarkZide Enthusiast Member Join Date: May 2010 Location: TN Posts: 291 Drives: 2010 370z BC M6 Rep Power: 14	on an N/A motor the amount of air near the intake isn't really a huge factor (unless there is just simply no air). Ram air setups and similar stuff make little to no difference, so there is probably minimal difference in here either. The big difference, if any, probably comes from the air being somewhat cooler where the G3 filters are verses right inside the engine bay like the R2C. Anyway, its still 500$ for these short ram intakes....how is it that people dont see how extemely overpriced parts are for these cars? Its a cheap metal pipe with a MAF mount welded on. Woopty do!

10-06-2011, 05:26 PM	#7 (permalink)
RCZ A True Z Fanatic Join Date: Nov 2008 Location: Miami Posts: 6,403 Drives: '09 370Z Rep Power: 1118	I'd wait for someone to be selling a set of G3's...

10-06-2011, 05:35 PM	#8 (permalink)
Nikkolai Base Member Join Date: Jun 2010 Location: DFW Posts: 238 Drives: Boss 302, Frontier Rep Power: 14	Or perhaps the Takeda long tube filters that do not require any cutting.

10-07-2011, 02:04 PM	#12 (permalink)
Methodical4u A True Z Fanatic Join Date: Jun 2011 Location: Maryland Posts: 1,393 Drives: 11 370 6mt pw w/sp Rep Power: 15	damnit Chris!!! We need some info!