Nissan 370Z Forum  

Stillen Gen3 Intake, Berk Hi-flow cat, and Stillen cat-back exhaust

Hey guys, I finished the install today. I started a few nights ago, doing a little after i got home late from work each night. Overall, the Stillen intakes are

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > Engine & Drivetrain > Intake/Exhaust


Like Tree1Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 04-25-2009, 10:23 PM   #1 (permalink)
Enthusiast Member
 
axio's Avatar
 
Join Date: Jan 2009
Location: SF Bay Area, CA
Posts: 271
Drives: '09 370Z
Rep Power: 16
axio will become famous soon enough
Default Stillen Gen3 Intake, Berk Hi-flow cat, and Stillen cat-back exhaust

Hey guys,

I finished the install today. I started a few nights ago, doing a little after i got home late from work each night. Overall, the Stillen intakes are pretty easy. I was pretty scared at first of damaging the front fascia during removal, but it wasn't that bad. Just make sure to unbolt all of the bolts underneath. The Nissan service manual's picture shows 4 bolts, but there's a total of 6 more bolts i had to take off to get this to come off. Just an FYI. The quality of the Stillen intakes appear to be pretty good.

For the Berk high-flow cats, definitely make sure to use some liquid wrench. The one in the DYI section showing you how to do the cat install works great, and was only a few dollars over at Home Depot. With the Stillen intakes in place, i was able to find clearance through the engine bay to get to those top bolts which gives everyone trouble. I stuck with using a breaker-bar and 1/2" drive extensions, u-joints and socket. The 1/2" drive tools were strong enough not to break. I did need extra leverage on one of the bolts so i used the bar from the racing jack and slipped it over the breaker-bar. By doing that, it made things much easier. The quality of the Berk cats look great.

Semtex, we were talking about the O2 sensor bung on the cats. There IS basically a very small opening where the bung connects to the body of the cat, so the steel wool trick in the bung should probably work and there's probably not much to worry about with it falling into the body of the cat. The hole at that junction is fairly small, probably just a LITTLE bit smaller than a hole in 3-ringed binder paper. I decided not to put the steel wool in there since I kinda forgot to pick some up and didn't remember until the install, and since there's plenty of room to get to them from underneath the car, i'll try out this fix in case i ever throw a CEL.

The Stillen exhaust was not hard to install. Removal of the stock exhaust was pretty easy and the Stillen exhaust easily went into place... until it was time to bolt the pieces up. Like everyone else, it seems, the Stillen exhaust would sit on the cross-brace. I followed the instructions, keeping the bolts loose, jacking up the area by the y-pipe and cross bar, then tightening up the bolts, but like everyone else it seems, the piping decided to rest on the cross-brace. I used some hose clamps as was suggested on this forum, and it still didn't have enough space to clear. I might go try to find some smaller hose clamps and give it another try. My other idea was to use those silicone mats you can find at Bed Bath Beyond and stuff, those silicone potholder squares or whatever you call em. I was gonna fold one in half to double-up the thickness and then place that in between the cross-brace and the exhaust. Obviously it'd still be resting on the exhaust but maybe it'll help dampen the rattling/raspy/vibration. The quality of the Stillen exhaust seems so-so to me. Two of my flanges were not straight, and seem to have been bent/warped backwards at the points where the bolts line up. And obviously how it rests on the cross-brace isn't that nice.

Overall, the car sounds great. It's definitely way louder than stock and it's pretty throaty. It sounds like a cross between an exotic and a V8, at least from what i can tell. The problem is i hear a lot of metallic rattles and vibration, sounding very raspy especially upon mid to wide open throttle. I'm assuming that this is cuz of the exhaust pipe resting on the cross-brace. I'll let you guys know tomorrow if the silicone square works in helping with the sound dampening.

As for how it feels? To be honest, I just finished breaking her in before i started putting these parts on, so i can't honestly tell you if there's any difference over stock. But there's a few people here that have been kind enough to dyno their cars with these mods to show unbiased gains. Thanks guys

If you're doing all this work in your own garage, it helps (with the cats at least) if you have something nicer than those little $20 floor jacks that only lift up to 14" high. Just a suggestion so you can get more clearance as you rest the car onto the jackstands. I also used hockey pucks as a cushion to help prevent any damage to the pinch rails.

I have a question though. Assuming the silicone square works as a buffer so the rattling is gone, is there anything wrong with leaving the exhaust resting onto the cross-brace? Will the constant heat transfer from the exhaust pipe damage or warp the cross-brace at all? After parking my car, i can still hear this clicking noise 10 minutes later from where the exhaust pipe rests on the cross-brace, i'm assuming from the expansion/contraction from the heat.

I'd take it to a muffler shop to have them try to fix it like other people in this forum have, but i won't be able to get to one until another two weeks. Plus i think it just really sucks that we pay all this money for an exhaust system just to have to take it back to a muffler shop and now pay to have them fix this when it should have been built with clearance in the first place.
axio is offline   Reply With Quote
Old 04-26-2009, 11:53 PM   #2 (permalink)
Enthusiast Member
 
axio's Avatar
 
Join Date: Jan 2009
Location: SF Bay Area, CA
Posts: 271
Drives: '09 370Z
Rep Power: 16
axio will become famous soon enough
Default

Alright, the silicone squares worked. there's no more rattling/vibration noise. I also figure that with the silicone blocking the direct contact heat from the exhaust pipes, the cross-brace should be ok.
axio is offline   Reply With Quote
Old 04-27-2009, 12:16 AM   #3 (permalink)
The370Z.com Sponsor
 
Josh@STILLEN's Avatar
 
Join Date: Dec 2008
Location: Costa Mesa, CA
Posts: 1,197
Drives: 2004 G35 Coupe 6MT
Rep Power: 533
Josh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond reputeJosh@STILLEN has a reputation beyond repute
Default

Awesome honest review on the install... you have a PM on the fitment of the exhaust.. with your input and others we've made some adjustment for easier install to clear the crossmember..

Can't wait to hear your thoughts on the power gains..
Josh@STILLEN is offline   Reply With Quote
Old 04-27-2009, 08:16 AM   #4 (permalink)
A True Z Fanatic
 
LiquidZ's Avatar
 
Join Date: Nov 2008
Location: Columbus, OH
Posts: 1,940
Drives: Mag. Black 2009 370Z
Rep Power: 704
LiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond reputeLiquidZ has a reputation beyond repute
Default

Quote:
Originally Posted by Josh@STILLEN View Post
Awesome honest review on the install... you have a PM on the fitment of the exhaust.. with your input and others we've made some adjustment for easier install to clear the crossmember..

Can't wait to hear your thoughts on the power gains..
Any ideas when these "fixed" exhausts will be available? I was holding out on buying your exhaust until the fitment issues were straightened out.
__________________
LiquidZ is offline   Reply With Quote
Old 04-27-2009, 09:10 AM   #5 (permalink)
Base Member
 
Join Date: Apr 2009
Location: bham al
Posts: 91
Drives: 05 g sedan 6mt
Rep Power: 15
t-ray is on a distinguished road
Default

Axio, do you hear any kind of hiss when decelerating, as the car gains vacuum? I've heard it in a couple of vids/clips of different exhausts, and that hiss has plagued me for 4 years now on my g35.

For a while, I thought it was an exhaust leak. But I've been through 8 different exhaust configurations, and its been present since the first exhaust mod. I've heard it on other g's and z's as well, and I'm afraid it might just be some inherent trait of the motor.
t-ray is offline   Reply With Quote
Old 04-27-2009, 09:36 AM   #6 (permalink)
Track Member
 
DannyGT's Avatar
 
Join Date: Jan 2009
Location: Jersey
Posts: 919
Drives: 370Z (SOLD)
Rep Power: 279
DannyGT has a reputation beyond reputeDannyGT has a reputation beyond reputeDannyGT has a reputation beyond reputeDannyGT has a reputation beyond reputeDannyGT has a reputation beyond reputeDannyGT has a reputation beyond reputeDannyGT has a reputation beyond reputeDannyGT has a reputation beyond reputeDannyGT has a reputation beyond reputeDannyGT has a reputation beyond reputeDannyGT has a reputation beyond repute
Default

Better yet, can those of us that have installed the exhaust and continue to have issue see some sort of replacement X pipe in the near future?

I will PM you guys...
__________________
Performance GTM Stage 1 SC, GTM Res.Test Pipes, Invidia Gemini Exhaust, GTM HD Oil Cooler
Wheels & Suspension AME Tracer TM02's 19x9.5F 19x10.5R w/ 265x35F & 305x30R, Hotchkis Sways, BC (BR) Racing Coilovers (Car Sold)
DannyGT is offline   Reply With Quote
Old 04-27-2009, 11:26 AM   #7 (permalink)
RCZ
A True Z Fanatic
 
RCZ's Avatar
 
Join Date: Nov 2008
Location: Miami
Posts: 6,403
Drives: '09 370Z
Rep Power: 1118
RCZ has a reputation beyond reputeRCZ has a reputation beyond reputeRCZ has a reputation beyond reputeRCZ has a reputation beyond reputeRCZ has a reputation beyond reputeRCZ has a reputation beyond reputeRCZ has a reputation beyond reputeRCZ has a reputation beyond reputeRCZ has a reputation beyond reputeRCZ has a reputation beyond reputeRCZ has a reputation beyond repute
Send a message via AIM to RCZ
Default

Quote:
Originally Posted by LiquidZ View Post
Any ideas when these "fixed" exhausts will be available? I was holding out on buying your exhaust until the fitment issues were straightened out.

They are already available.
RCZ is offline   Reply With Quote
Old 04-27-2009, 02:32 PM   #8 (permalink)
Enthusiast Member
 
axio's Avatar
 
Join Date: Jan 2009
Location: SF Bay Area, CA
Posts: 271
Drives: '09 370Z
Rep Power: 16
axio will become famous soon enough
Default

T-Ray, i don't really hear a hiss when decelerating. The exhaust itself sounds pretty good.

Unfortunately my silicone square fix isn't going to work. I checked it last night and the direct heat from the pipe is melting the silicone square. Looks like i'll have to wait out the two weeks before I can find time to take the car into a muffler shop and pay someone to heat and bend the pipes...
axio is offline   Reply With Quote
Old 04-27-2009, 04:14 PM   #9 (permalink)
A True Z Fanatic
 
wstar's Avatar
 
Join Date: Mar 2009
Location: Houston, TX
Posts: 4,024
Drives: too slow
Rep Power: 3594
wstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond reputewstar has a reputation beyond repute
Default

Quote:
Originally Posted by axio View Post
T-Ray, i don't really hear a hiss when decelerating. The exhaust itself sounds pretty good.

Unfortunately my silicone square fix isn't going to work. I checked it last night and the direct heat from the pipe is melting the silicone square. Looks like i'll have to wait out the two weeks before I can find time to take the car into a muffler shop and pay someone to heat and bend the pipes...
Yeah exhaust temps are a little higher than your usual cooking temps, but for trying it anyways. When I was in the same boat, I googled around looking for an industrial source of higher-temp rubber mat that might work, but never found anything that really looked satisfactory for this application. It'll all be better once you get it bent. The hard part is just finding a good exhaust guy to do the work, if you don't already know one.

The guy I found that fixed mine is really cool, I've been recommending him to everyone around here. He's cheap, he's a genius, very laid back shop, cash transactions, etc His website looks like it was designed by a 13 year old in 1994, but the work was excellent: AFFORDABLE MUFFLERS, L.L.C. , Mufflers & Exhaust Systems, Houston

Too bad you're not in Houston though.
__________________
7AT Track Car!
Journal thread / Car setup details
wstar is offline   Reply With Quote
Old 04-27-2009, 04:19 PM   #10 (permalink)
A True Z Fanatic
 
semtex's Avatar
 
Join Date: Jan 2009
Location: Behind enemy lines
Age: 53
Posts: 5,995
Drives: People to drink
Rep Power: 32
semtex has a reputation beyond reputesemtex has a reputation beyond reputesemtex has a reputation beyond reputesemtex has a reputation beyond reputesemtex has a reputation beyond reputesemtex has a reputation beyond reputesemtex has a reputation beyond reputesemtex has a reputation beyond reputesemtex has a reputation beyond reputesemtex has a reputation beyond reputesemtex has a reputation beyond repute
Default

Wow, you're not kidding about the design of his website. Had me laughing out loud.
__________________
"There are no small accidents on this circuit." -- Ayrton Senna
316.8whp & 248 ft/lbs (Dyno Dynamics) | 319whp & 256 ft/lbs (DynoJet) (04/23/10)
Stillen G3 CAI, CBE, Pulley / F.I. LTH / GTSpec Ladder Brace / Setrab Oil Cooler / UpRev-tuned by Forged Perf.
semtex is offline   Reply With Quote
Old 04-27-2009, 06:40 PM   #11 (permalink)
Base Member
 
ZforMe's Avatar
 
Join Date: Jan 2009
Location: Memphis TN
Posts: 238
Drives: 370Z Sport Auto PG
Rep Power: 16
ZforMe is on a distinguished road
Default

Quote:
Originally Posted by semtex View Post
Wow, you're not kidding about the design of his website. Had me laughing out loud.
^ Agreed, not to mention it caused me to have 3 epileptic seisures.
ZforMe is offline   Reply With Quote
Old 04-27-2009, 07:04 PM   #12 (permalink)
Base Member
 
tonmed123's Avatar
 
Join Date: Apr 2009
Location: Houston,Texas
Posts: 223
Drives: 09 370Z Red M6
Rep Power: 266
tonmed123 has a reputation beyond reputetonmed123 has a reputation beyond reputetonmed123 has a reputation beyond reputetonmed123 has a reputation beyond reputetonmed123 has a reputation beyond reputetonmed123 has a reputation beyond reputetonmed123 has a reputation beyond reputetonmed123 has a reputation beyond reputetonmed123 has a reputation beyond reputetonmed123 has a reputation beyond reputetonmed123 has a reputation beyond repute
Smile

Thanks Wstar for posting your muffler guy. Ill be sure to go check him out when Im ready.
tonmed123 is offline   Reply With Quote
Old 04-28-2009, 01:49 AM   #13 (permalink)
Enthusiast Member
 
axio's Avatar
 
Join Date: Jan 2009
Location: SF Bay Area, CA
Posts: 271
Drives: '09 370Z
Rep Power: 16
axio will become famous soon enough
Default

Quote:
Originally Posted by wstar View Post
Yeah exhaust temps are a little higher than your usual cooking temps, but for trying it anyways. When I was in the same boat, I googled around looking for an industrial source of higher-temp rubber mat that might work, but never found anything that really looked satisfactory for this application. It'll all be better once you get it bent. The hard part is just finding a good exhaust guy to do the work, if you don't already know one.

The guy I found that fixed mine is really cool, I've been recommending him to everyone around here. He's cheap, he's a genius, very laid back shop, cash transactions, etc His website looks like it was designed by a 13 year old in 1994, but the work was excellent: AFFORDABLE MUFFLERS, L.L.C. , Mufflers & Exhaust Systems, Houston

Too bad you're not in Houston though.
Yeah, the tag said it was heat resistant up to 600 degrees... guess they lied.

As for the exhaust guy, I'm gonna take it to my friend's mechanic. Luckily he's open on Sunday so I can make it this weekend afterall. Unfortunately he said he doesn't have a hot torch so if he can't do it the way the Stillen guys recommended, he was gonna try to hammer and bend the pipe. I'm gonna assume he knows his stuff since me basically built my friend's 900whp Supra, so hopefully a few minor bends without using heat will be ok. Thanks for the shop recommendation though, but yeah, Houston might be a little far haha
axio is offline   Reply With Quote
Old 04-28-2009, 07:28 AM   #14 (permalink)
Base Member
 
Join Date: Mar 2009
Location: killeen tx
Posts: 202
Drives: black 09 370Z 6spd
Rep Power: 16
black09Z is on a distinguished road
Default

so if i buy the exhaust now it wont have the fitment issue correct?
black09Z is offline   Reply With Quote
Old 04-28-2009, 11:20 AM   #15 (permalink)
Base Member
 
ocfoilist's Avatar
 
Join Date: Apr 2009
Location: Orange County, CA
Posts: 202
Drives: 09 Blue 6m 370zT/S/N
Rep Power: 15
ocfoilist is on a distinguished road
Default

As a relative noobie to after-market installs, it seems that many on the board have gone with the Stillen intake and cat-back, but with the Berk hi-flow cats. Is this because the Berk offers some substantial benefit over Stillen's product? It sounds like there is a (mild) issue with fitting. I am considering getting the three for my 370 and my instinct was to just go with Stillen all the way for consistency sake. Any advice would be much appreciated!

Besides, Josh is about 4 buildings away from where I used to work on Airport loop...
__________________
Proud owner of a new 167.2 inch, 3278 lb baby Z!
Stillen CBE & G3 Intake // Stillen Lightweight pulley // Stillen Oil Cooler // Goodridge Braided Stainless Steel Brake Lines // ACT HDSS Clutch& Alum Flywheel
ocfoilist is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Stillen HFC vs. BERK HFC ZforMe Intake/Exhaust 181 09-15-2010 01:35 AM
Stillen Exhaust with Berk HFCs semtex Intake/Exhaust 127 12-01-2009 02:53 PM
STILLEN 370Z Dual Cat-Back Stainless Exhaust System sktvietdragon Intake/Exhaust 103 05-09-2009 06:06 PM
Stillen Headers + Berk HFCs self-install report wstar Intake/Exhaust 84 04-14-2009 12:09 PM
STILLEN Exhaust & Gen 3 Intake Dynos - 18hp Each! Josh@STILLEN Intake/Exhaust 96 03-09-2009 03:33 PM


All times are GMT -5. The time now is 07:47 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2