My new HPS post MAF tubes installed

GZ3 · 02-14-2011, 03:48 PM

Quote:

Originally Posted by Jordo!

panel filters, plus tubes, plus the ART pipes (which seem to make a little more power than standard TP's) and even a Y pipe should get you in the upper 290's -- close to 300 on a dynojet... so... yeah, probably.

I don't know if you'll break 300 without a tune using SAE correction, but you should definitely be in the ball park.

Oh, and 10-12 for high flow filters AND the tubes, is definitely believable.

Yeah i hope to be at 300 + - 5rwhp...kast had about 296 with what i had plus a ypipe...either way i will do a full report with dyno and TQ readings this time.

natepaulus · 02-14-2011, 06:17 PM

Quote:

Originally Posted by TonyBPD

In stock now at CorSport. I just ordered a set.

Indeed. I ordered last Tuesday and I just knew i had missed a window of availability. 6 days later, I have a brown box full of HPS parts.

I also odrered the K&N drop ins, which arrived Friday, and were dropped in 2 minutes after opening. I know the car pretty well by now so I can say with confidence, that I immediately noticed a slight increase in throttle response. Is that possible with just a higher flowing air filter?? Trying hard to attribute it to placebo effect..(But I can still feel it, undeniably)

Definitely looking forward to putting these on now. I've got the F.I. TDX 18" with HCF ordered as well. SOMEBODY... give me a reason not to change my order to the L.T.H's....phuckin lovin the idea of more low end torque. (another thread, yes, I know).

elmz · 02-17-2011, 09:32 AM

I ordered HPS tubes on Sat and still no package

. I can't wait to install them.

'10Anamoly · 02-17-2011, 09:41 AM

Be sure to re-dyno before/after on the same one to see appropriate gains.

cujo · 02-17-2011, 12:19 PM

I just sent my order last night and it's back ordered at this point

Not sure how long this will take....

Mr. Q · 02-17-2011, 12:42 PM

Quote:

Originally Posted by elmz

I ordered HPS tubes on Sat and still no package

. I can't wait to install them.

you say that now but when you are fighting and cursing your airboxes you'll be singing a different tune. Unless you remove your strut bar the install can be a pain if you dont want to trim anything.

chops · 02-17-2011, 07:59 PM

Quote:

Originally Posted by cujo

I just sent my order last night and it's back ordered at this point

Not sure how long this will take....

mines been back ordered for almost 3 weeks.....

Mr. Q · 02-18-2011, 12:03 PM

Any reason not to get the cobb tubes? Those were in stock

GZ3 · 02-18-2011, 12:53 PM

Quote:

Originally Posted by Mr. Q

Any reason not to get the cobb tubes? Those were in stock

last i heard they were out and no plans to remake. When i was looking they only had blue too

Mr. Q · 02-18-2011, 01:41 PM

I guess I got near the last ones then plus my car is blue. Any chance the ones for the 350 fit ours cause they still have those

Machine · 02-18-2011, 09:12 PM

Ordered from Corsport this passed Thursday, received today, and installed this evening. I didn't remove the strut tower brace and really didn't feel this was that difficult, I got lucky I guess. No need to trim these, as instructions mention, perfect fit. I also have the AFE dry filters. Butt-dyno approved.

GZ3 · 02-18-2011, 09:29 PM

Quote:

Originally Posted by Machine

Ordered from Corsport this passed Thursday, received today, and installed this evening. I didn't remove the strut tower brace and really didn't feel this was that difficult, I got lucky I guess. No need to trim these, as instructions mention, perfect fit. I also have the AFE dry filters. Butt-dyno approved.

Good Man! thats my exact intake set up

cujo · 02-18-2011, 09:48 PM

Don't remove the strut tower, just lube it with a little KY Jelly...Any works with KY Jelly ha ha

Mr. Q · 02-18-2011, 10:13 PM

Quote:

Originally Posted by cujo

Don't remove the strut tower, just lube it with a little KY Jelly...Any works with KY Jelly ha ha

I didn't remove the strut tower and had no lube but a little sweet talking and a lot of force and she finally gave in. Wait what are we talking about? Also the Cobb tubes just came in a box with a receipt and no instructions only in hindsight did I think it would have been easier without the tower there, and now KY

gorpie · 02-20-2011, 02:50 PM

I finally decided to install my HPS tubes today and ran into some problems. The left side tube fit just fine and all hook up great. The right side tube would hook up to the air box and the intake just fine but the alignment of the little plastic box would not line up at all. I could get it hooked up but then it puts a bad kink in the main intake hose. I tired both tubes and same problem on the right side.
Both of my HPS intake tubes are exactly alike. Is there suppose to be a right and a left? The tubes came in separate plastic bags with different part numbers on them, but they are the same. I worked on this project for two hours (most all of that was scratching my head) which should have taken 15 minute for the whole thing. Bottom line is that I didn’t like what I saw so put it all back to stock.

02-17-2011, 09:41 AM	#79 (permalink)
'10Anamoly Track Member Join Date: May 2010 Location: GA Posts: 882 Drives: 2010 370Z BS M6 Rep Power: 15	Be sure to re-dyno before/after on the same one to see appropriate gains. __________________ 2013 Ford Mustang GT 374rwhp, 360rwtq SAE / GT500 Axle-Backs / Brembo Pack / Track Pack / Recaros / 6spd

02-17-2011, 12:19 PM	#80 (permalink)
cujo Base Member Join Date: Nov 2010 Location: California Posts: 99 Drives: 2010 370z Roadster Rep Power: 14	I just sent my order last night and it's back ordered at this point Not sure how long this will take.... __________________ Brilliant Silver/Roadster/Touring/6MT/Fast Intentions.

02-18-2011, 09:48 PM	#88 (permalink)
cujo Base Member Join Date: Nov 2010 Location: California Posts: 99 Drives: 2010 370z Roadster Rep Power: 14	Don't remove the strut tower, just lube it with a little KY Jelly...Any works with KY Jelly ha ha __________________ Brilliant Silver/Roadster/Touring/6MT/Fast Intentions.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
COBB Tuning Post MAF Tubes	hfrog355	Exhaust/Intake	1	03-03-2011 04:37 PM
FS: Cobb Post-MAF intake tubes (Black)	ArtVandaleigh	Parts for sale (Private Classifieds)	4	10-04-2010 10:14 PM
WTB: COBB post-Maf tubes - Black	kielbasa16	Parts for sale (Private Classifieds)	10	07-29-2010 09:05 AM
FS: Cobb Black Silicone Post-MAF Tubes	'10Anamoly	Parts for sale (Private Classifieds)	21	07-16-2010 07:39 AM

02-17-2011, 09:32 AM	#78 (permalink)
elmz Track Member Join Date: Feb 2009 Location: San Diego, CA Posts: 674 Drives: 2014 Porsche Boxster Rep Power: 17	I ordered HPS tubes on Sat and still no package . I can't wait to install them.

02-18-2011, 12:03 PM	#83 (permalink)
Mr. Q Enthusiast Member Join Date: Dec 2009 Location: Texas Posts: 349 Drives: 09 MB 370z Rep Power: 15	Any reason not to get the cobb tubes? Those were in stock

02-18-2011, 01:41 PM	#85 (permalink)
Mr. Q Enthusiast Member Join Date: Dec 2009 Location: Texas Posts: 349 Drives: 09 MB 370z Rep Power: 15	I guess I got near the last ones then plus my car is blue. Any chance the ones for the 350 fit ours cause they still have those

02-18-2011, 09:12 PM	#86 (permalink)
Machine Base Member Join Date: Jul 2010 Location: Alabama Posts: 16 Drives: 94 Z32, 09 Z34 Rep Power: 14	Ordered from Corsport this passed Thursday, received today, and installed this evening. I didn't remove the strut tower brace and really didn't feel this was that difficult, I got lucky I guess. No need to trim these, as instructions mention, perfect fit. I also have the AFE dry filters. Butt-dyno approved.