Nissan 370Z Forum  

Calling Stillen SC Owners with upgraded kits

Originally Posted by tsui_san Saw in your sig that you're running 9lb pulley on 91 oct. I'm currently running the kit with the 8lb pulley but want to upgrade. I've

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > Engine & Drivetrain > Forced Induction


Like Tree25Likes

 
 
LinkBack Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 08-17-2014, 11:06 AM   #11 (permalink)
Track Member
 
Join Date: Dec 2011
Location: Bay Area
Posts: 555
Drives: 10 Nissan 370z
Rep Power: 15
future370zzz will become famous soon enoughfuture370zzz will become famous soon enough
Default

Quote:
Originally Posted by tsui_san View Post
Saw in your sig that you're running 9lb pulley on 91 oct. I'm currently running the kit with the 8lb pulley but want to upgrade. I've been recommended only to run that setup either with 93oct or meth inject to prevent detonation. What's your experience been with the 9lb pulley on 91oct? Any reliability issues or other quirks?

Also interested in an impeller upgrade also...surprised you haven't blown your motor yet.
Haven't come up with any reliability issues yet (knock on wood). I let the car and SC warm up properly before stomping on it. Only quirk is the power and torque levels are bumped up compared to the standard kit.

I prevent detonation with this setup by not stomping on it when's it 90 degrees out. It's a shame that this car doesn't have a knock sensor that can be used to monitor it.

The tune from Rob at z car garage is conservative to prevent detonation, can't stop it. He runs it on the dyno and tunes it aggressively until it starts detonating and pulls back the tune a couple notches. There is always risk with aftermarket setups. I installed a temp probe near the Stillen manifold and saw changes of up to 30 degrees within 5 seconds of boosting/stomping. The temps stabilize within 10-20 seconds of normal driving.

The goal for me is to bump the area under the curve for more usable power for my driving (street driving, stop and go) and to sustain that power level and keep the engine as safe as possible. The impeller upgrade and 9psi bump up the power from the standard kit and the test pipes lower the peak boost (seeing 9.8 psi on the dyno and 10.8 on my boost gauge - thinking that it would be 2 psi more if I threw the stock cats back on - problem is increased heat and potential for detonation). The future air to air intercooler addition and vented hood would delay heat soak and generally lower engine temps (air charge temps).

The blown motors I have heard about seem to be from running at the drag strip or running the motor hard for an extended period of time on high boost (12 to 13 seconds haha and repeated boosted runs).

I don't know what the standards are for a boosted car in terms of how long you can stomp on the car until it blows. Maybe your tuner is expecting you to stomp on it all the time so the practical thing to do with impeller and 9psi kit is to use 93 or meth so you can run hard all the time and at the same time pick up safe power/torque that doesn't make the upgrade a disappointment. For my setup, I feel my power numbers are low but I believe that they are safe and right now safety is higher on my list. I wasn't expecting much from the craptastic 91 octane so I wasn't disappointed by the number. The car feels great though.

Z car did mention that a mix of 93 would be a good safeguard against bad 91 gas and when it gets really hot. 7 gallons of 93 mixed with 91 remaining give me 92 octane. This is my extra safeguard against detonation in addition to

My goal was not to make the most power on crappy 91 octane but with either 100 octane or e85 if I get the itch for more power. I already have enough problems trying to keep the tires from spinning with the current power level (in 1st mostly but the quaife has helped make the most of the power).
__________________

Last edited by future370zzz; 08-17-2014 at 11:15 AM.
future370zzz is offline   Reply With Quote
 

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Calling all motorcycle owners! SgtGoldy The Lounge (Off Topic) 17 02-11-2014 10:59 PM
Calling all sc z car owners! foxcrazy South East Region 24 08-23-2011 10:06 AM
****Specialty-Z Flywheel & Clutch Kits w\ Upgraded CSC**** Seb@SZ Drivetrain/Engine 7 03-17-2011 02:14 PM
New & Upgraded Kits From Adam's Polishes AdamsPolishes Adam's Polishes 0 07-23-2010 04:39 PM
calling all kenwood owners ddvette9 Audio & Video 57 12-30-2009 03:32 PM


All times are GMT -5. The time now is 03:00 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2