GTM 1.5 need suggestions on build

SS_Firehawk · 02-07-2014, 05:56 PM

Intake temps were about 10-15 above ambient if I recall. It was surprisingly good considering I have unshielded long tubes sitting right below and snaking past two Superchargers

martin82 · 02-08-2014, 11:31 PM

Thanks, does anyone have updated install manual? The manual I have shows two air filters in passenger side, but mine has a green filter...

martin82 · 02-08-2014, 11:32 PM

George@GTM · 02-09-2014, 02:39 AM

Martin,

Glad to see you are installing the kit I am sure you will be very pleased

It seems you are looking at the instructions for a Stage 1 kit and you need the Stage 1.5 instructions. I will PM them to you tomorrow.

Have fun!

-George

roplusbee · 02-09-2014, 03:36 AM

Martin:

Perhaps your dilemma is airflow over the oil cooler itself. If you can find a way to maximize airflow, the 34 row would make it's money for you. I haven't taken mine on any circuit yet, but I ran the Dragon and the two connecting highways in 2 loops while they were doing the car show during ZDayZ 2013. Lets just say, I drove gingerly and my temps never exceeded 230.

As far as clutch goes, I have the ZSpeed CSC and SS braided lines. I have Competition Clutch's Twin Disk and it is the money. You may have to call them about it because I haven't seen it on their site, but John from Zerolift told me that it was a beast to install. OS Giken is a sure shot as well, but you are going to pay for it. I have no experience with OS Giken in a Z, but I had their twin disk in 2 out of 3 S13s I owned.

Sent via Tapatalk 4 on D-Team Note II

martin82 · 02-10-2014, 01:55 PM

George just sent you a PM

martin82 · 02-11-2014, 04:27 PM

Car is up on lift and will be taking apart front to back!!

Still need:
New or updated instructions
Can tuned
Radiator, fan shroud, oil baffled pan?
Decide on clutch

Shipped: Phunk's rrp fuel fix thanks!!

George@GTM · 02-12-2014, 02:26 AM

Quote:

Originally Posted by martin82

George just sent you a PM

Replied, Car looks good

Liquid_G · 02-12-2014, 09:50 AM

FWIW, I've been super happy with my Stg3 Ceramic clutch from Competition Clutch. Over a year with it now, including one track day and its held up pretty well.

martin82 · 02-12-2014, 07:36 PM

thanks!

I am having some problems with installation. My installer says it is where the PS Steering Bracket and Alternator bracket are.

The manual calls for a M10x1.25x128mm bolt, but the bolt is almost 1/4" too short, the bolt only threads about 1-2 turns. Anyone got any ideas? Also, the installer says they ordered a longer bolt but even then, the bracket hole is counter sunk so they won't be able to tighten it with a socket. Installer says we would need a socket head cap screw with allen wrench. Ideas, thoughts?

Matt@GTM · 02-12-2014, 07:52 PM

That should be right, can you post up a pic from the side of what you have looks like so far? I'm assuming you have the two alternator brackets bolted together and mounted to the side of the engine as well as the main bracket correct? We only carry one bolt around that length so the chances are low that it is the wrong one, it seems something else is a miss.

martin82 · 02-12-2014, 08:14 PM

I don't have a picture of it at the moment, but I asked the installer, and I circled it he said it is this bolt he says it can only thread 1-2 turns only. I could have the wrong bolt not sure... there has been no change on a 2012 I assume? Thanks.

martin82 · 02-12-2014, 08:22 PM

One more pic of the bolt I'm talking about (not my picture) , Matt@gtm can I get one sent overnight tomorrow? I'll pay for it offcourse says it is 1/4" too short thought, maybe you or someone can measure it really quick?

Baer383 · 02-12-2014, 08:54 PM

The bolt is not short you have to put your other hand behind the alt to push the captured nut forward for it to start.

And I can guarantee your installer DID NOT measure the length of the bolts as shown in the directions.
And installed the bolt in the wrong spot.

martin82 · 02-12-2014, 09:07 PM

I think the actual bolt in the picture is missing, I will know tomorrow once I get pictures.

02-07-2014, 05:56 PM	#31 (permalink)
SS_Firehawk Premium Member Join Date: Oct 2011 Location: Tampa Posts: 4,142 Drives: 13' Magma Red Nismo Rep Power: 7334	Intake temps were about 10-15 above ambient if I recall. It was surprisingly good considering I have unshielded long tubes sitting right below and snaking past two Superchargers __________________ Old Car:GTM TSC'd 550whp / 410lbft tq @ 11.88PSI New Car: Under Construction

02-09-2014, 03:36 AM	#35 (permalink)
roplusbee A True Z Fanatic Join Date: Dec 2009 Location: Killeen, TX Posts: 2,360 Drives: 2007 350Z NISMO Rep Power: 22	Martin: Perhaps your dilemma is airflow over the oil cooler itself. If you can find a way to maximize airflow, the 34 row would make it's money for you. I haven't taken mine on any circuit yet, but I ran the Dragon and the two connecting highways in 2 loops while they were doing the car show during ZDayZ 2013. Lets just say, I drove gingerly and my temps never exceeded 230. As far as clutch goes, I have the ZSpeed CSC and SS braided lines. I have Competition Clutch's Twin Disk and it is the money. You may have to call them about it because I haven't seen it on their site, but John from Zerolift told me that it was a beast to install. OS Giken is a sure shot as well, but you are going to pay for it. I have no experience with OS Giken in a Z, but I had their twin disk in 2 out of 3 S13s I owned. Sent via Tapatalk 4 on D-Team Note II __________________ 2007 350Z NISMO #0618: Zerolift \| UPREV \| F.I. \| Greddy \| Competition Clutch \| Injector Dynamics \| Aeromotive \| Pioneer \| JL

02-11-2014, 04:27 PM	#37 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 19	Car is up on lift and will be taking apart front to back!! Still need: New or updated instructions Can tuned Radiator, fan shroud, oil baffled pan? Decide on clutch Shipped: Phunk's rrp fuel fix thanks!! Mandingo likes this.

02-12-2014, 09:50 AM	#39 (permalink)
Liquid_G A True Z Fanatic Join Date: Aug 2009 Location: Chicago Burbs Posts: 1,439 Drives: 09 370z Supercharged Rep Power: 43	FWIW, I've been super happy with my Stg3 Ceramic clutch from Competition Clutch. Over a year with it now, including one track day and its held up pretty well. __________________

02-12-2014, 08:14 PM	#42 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 19	I don't have a picture of it at the moment, but I asked the installer, and I circled it he said it is this bolt he says it can only thread 1-2 turns only. I could have the wrong bolt not sure... there has been no change on a 2012 I assume? Thanks. Last edited by martin82; 02-12-2014 at 08:17 PM.

02-08-2014, 11:31 PM	#32 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 19	Thanks, does anyone have updated install manual? The manual I have shows two air filters in passenger side, but mine has a green filter...

02-08-2014, 11:32 PM	#33 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 19

02-09-2014, 02:39 AM	#34 (permalink)
George@GTM NOT AN ACTIVE VENDOR. DO NOT BUY Join Date: Dec 2008 Location: California Posts: 146 Drives: TTG41 Rep Power: 16	Martin, Glad to see you are installing the kit I am sure you will be very pleased It seems you are looking at the instructions for a Stage 1 kit and you need the Stage 1.5 instructions. I will PM them to you tomorrow. Have fun! -George

02-10-2014, 01:55 PM	#36 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 19	George just sent you a PM

02-12-2014, 07:36 PM	#40 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 19	thanks! I am having some problems with installation. My installer says it is where the PS Steering Bracket and Alternator bracket are. The manual calls for a M10x1.25x128mm bolt, but the bolt is almost 1/4" too short, the bolt only threads about 1-2 turns. Anyone got any ideas? Also, the installer says they ordered a longer bolt but even then, the bracket hole is counter sunk so they won't be able to tighten it with a socket. Installer says we would need a socket head cap screw with allen wrench. Ideas, thoughts?

02-12-2014, 07:52 PM	#41 (permalink)
Matt@GTM Not an active vendor. DO NOT PURCHASE Join Date: Mar 2013 Location: California Posts: 44 Drives: 370Z Rep Power: 297	That should be right, can you post up a pic from the side of what you have looks like so far? I'm assuming you have the two alternator brackets bolted together and mounted to the side of the engine as well as the main bracket correct? We only carry one bolt around that length so the chances are low that it is the wrong one, it seems something else is a miss.

02-12-2014, 08:22 PM	#43 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 19	One more pic of the bolt I'm talking about (not my picture) , Matt@gtm can I get one sent overnight tomorrow? I'll pay for it offcourse says it is 1/4" too short thought, maybe you or someone can measure it really quick? Last edited by martin82; 02-12-2014 at 08:24 PM.

02-12-2014, 08:54 PM	#44 (permalink)
Baer383 A True Z Fanatic Join Date: Aug 2010 Location: Lawrenceville,Ga Posts: 4,293 Drives: My foot up your azz Rep Power: 29	The bolt is not short you have to put your other hand behind the alt to push the captured nut forward for it to start. And I can guarantee your installer DID NOT measure the length of the bolts as shown in the directions. And installed the bolt in the wrong spot. __________________ 2013 ZL1 754 rwhp 747 rwtq Last edited by Baer383; 02-12-2014 at 08:57 PM.

02-12-2014, 09:07 PM	#45 (permalink)
martin82 A True Z Fanatic Join Date: Nov 2011 Location: los angeles Posts: 2,636 Drives: 12 Nissan 370Z MB M6 Rep Power: 19	I think the actual bolt in the picture is missing, I will know tomorrow once I get pictures.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Gym Rats enter! Suggestions Suggestions!	Asheth	The Lounge (Off Topic)	50	04-18-2013 04:36 PM
THE "Lets argue about Bullitt's build with out ruining Bullitt's build thread" THREAD	Reaper42	Forced Induction	14	01-22-2011 05:24 PM
Datsun Roadster 1600...To build or not to build	motoextreme	The Lounge (Off Topic)	66	02-13-2010 12:40 AM
need some suggestions~come in have a look~thank u~	niznizbobo	Wheels & Tires	15	09-25-2009 03:27 AM
Any Suggestions?	Burnrubber101	Nissan 370Z General Discussions	12	03-06-2009 08:30 AM