time to change that sig.
Nice numbers.

http://i94.photobucket.com/albums/l1.../home009-1.jpg
much better torque do to tuning to get more torque out of the set-up

Dyno pack not dynojet sry for the mix-up the power is at the wheel or hub

on still a work in progress
just got my snow kit
http://i94.photobucket.com/albums/l1...r/IMG_1572.jpg

http://i94.photobucket.com/albums/l1...r/IMG_1837.jpg

looking into getting a pulley size smaller on the vortech

i have to measure it but cant remember what size the 9lb pulley is anyways i will be dropping down one more size from that

once i get the pulley its back to je imports for the water-meth and pulley install and new tune
i was going to go with the cog pulley but i thing this 8-rib should hold up fine

now with the 9lb pulley i was seeing 9-10 doing warm weather and 10-11 doing the cold weather
i am hoping for a solid 11psi with a more but no overly aggressive tune

still need more torque :(

hehe ya i know rigth !!

i got to work with what i have :rolleyes:

just going to have to race from a roll :tup:

ok so i are still working to get that magic 500rwhp number
the water/meth kit and oil cooler is installed once again nice work from the boys at je import on the custom mounting and install

http://i94.photobucket.com/albums/l1...r/IMG_8946.jpg

http://i94.photobucket.com/albums/l1.../IMG_23131.jpg

just have to filler her up with boost juice then we will put the car back on the dyno

also after a few hard runs with the oil cooler normally it would be 220-230 with 250 spikes now it is sitting at 190-200 with 220 spikes so much better on the cooling i am using the 19 row stillen cooler

With that snow kit you should easily hit your 500RWHP goal. If the shop tunes for it just be sure you don't run out of juice or bad things will happen LOL

I wanted 500RWHP in my Challenger and ended up close to 600 or a bit over. It's a bit hairy on street tires.

I figured 400RWHP would be phenomenal in a car this light, I can't imagine 500 with this short wheel base go cart of a car LOL

it's really not that bad...I'm not at 500hp yet but getting closer...within 30-40 right now.

Clean looking install. That looks really nice.:tup:

Good luck and I hope you reach your goals!

But, one thing to keep in mind, the biggest gain in power after adding meth injenction is being able to turn the boost up. Do you plan on getting yet another pulley? If not, I really hope there are still a few more degrees of timing left on the table.

good choice on the meth kit, definitely going to see a good bump in power with some more aggressive timing. the only thing that really bothered me about the stillen setup is that the car is blind to true IAT's. From my understanding if your IAT's are too hot, it should retard timing, if they are cool it would allow for advance. IAT is based of the driver side MAF sensor, and all it can read with stillens setup is ambient air temp.

I will talk to my tuner, I did talk about maybe changing the setup to a blow-throught setup by cutting the piping between the blower and intake an moving 2 Maf sensors to a box config that would go between the blower

Or maybe try and put some kind of ait sensor after the intake manifold inter cooler to get the best true reading I am just guessing here. Thinking out loud

Your only option is to find an IAT sensor that has a similar voltage output compared to stock (check the FSM). Drill/tap the stillen plenum after the IC and tap the output into the MAF signal to feed the ecu a proper IAT signal.

The 9 pound pulley is 2.75 that's what I got when I measured. You can order a smaller pulley from 928 motorsports 928 Motorsports - Porsche® 928 Performance Parts - 8-Rib Power Pulleys for Powerdyne, Vortech, Paxton Superchargers.

If you do I would look into a smaller belt and install a idler pulley like in this picture to get more belt wrap and prevent belt slippage.http://www.the370z.com/drivetrain-en...arger-kit.html

But once you do this I think your going to Max out your maf's for sure. I did with my set up and 3.12 pulley that comes with the kit.

You are doing good with the kit nice choice on the Meth kit nice job:tup:

nice out so some go pro action work in progress!!!
370z ark cat-back - YouTube

:tup:Car sound good man keep up the good work