Wueros tt build

Elmo370z · 12-29-2020, 06:15 PM

Quote:

Originally Posted by Wuero370z

Oh shoot I didn’t realize they were different. I see those for 2540 right?

https://www.driveshaftshop.com/impor...ro-level-axles

Sent from my iPhone using Tapatalk

Justin was launching at 7,000 Rpms on a stock axles. Did you load the rear end before dumping the clutch?

Spooler · 12-29-2020, 06:42 PM

Quote:

Originally Posted by Elmo370z

Justin was launching at 7,000 Rpms on a stock axles. Did you load the rear end before dumping the clutch?

He was but they were looking ugly. Load it with the clutch or not they will break.

Elmo370z · 12-29-2020, 09:11 PM

Quote:

Originally Posted by Spooler

He was but they were looking ugly. Load it with the clutch or not they will break.

Justin’s never broke with iver 50 passes at the drag strip. Yes they will break eventually. But not using the proper setup for oem axles, they will break more often. Either shocking the suspenion or putting to much load on them. But I agree with upgrading the axles, but with that still a crap shot at it fixing the solution. Not data to prove they will work for our cars.

Spooler · 12-29-2020, 09:59 PM

Quote:

Originally Posted by Elmo370z

Justin’s never broke with iver 50 passes at the drag strip. Yes they will break eventually. But not using the proper setup for oem axles, they will break more often. Either shocking the suspenion or putting to much load on them. But I agree with upgrading the axles, but with that still a crap shot at it fixing the solution. Not data to prove they will work for our cars.

He was just lucky. One wrong move and TINK!!!!! Gone.

Wuero370z · 12-29-2020, 10:05 PM

Quote:

Originally Posted by Elmo370z

Justin was launching at 7,000 Rpms on a stock axles. Did you load the rear end before dumping the clutch?

I did not. I believe I will start preloading it but need to get a better brake setup or a handbrake

Sent from my iPhone using Tapatalk

Elmo370z · 12-30-2020, 07:55 AM

Quote:

Originally Posted by Wuero370z

I did not. I believe I will start preloading it but need to get a better brake setup or a handbrake

Sent from my iPhone using Tapatalk

That’s why your axles snapped. Oem
Axles can handle a lot of power, but you have to be careful launching the car especially on a prepped surface.

Spooler · 12-30-2020, 08:21 AM

Quote:

Originally Posted by Elmo370z

That’s why your axles snapped. Oem
Axles can handle a lot of power, but you have to be careful launching the car especially on a prepped surface.

That's the point. Slipping the clutch like that kills it. So folks put in axles. The better the prep, the worse it gets. To get a more consistent launch folks use clutch delay valves. The fast manual tranny guys use a slipper clutch.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The Mag Z Build	TheMagZ	Member's 370Z Gallery	16	07-09-2016 07:46 PM
My Build	skoolio	Member's 370Z Gallery	6	02-08-2016 08:55 PM
TT build in Fl	travnflorida	Nissan 370Z General Discussions	3	08-15-2011 05:51 PM
THE "Lets argue about Bullitt's build with out ruining Bullitt's build thread" THREAD	Reaper42	Forced Induction	14	01-22-2011 05:24 PM
Datsun Roadster 1600...To build or not to build	motoextreme	The Lounge (Off Topic)	66	02-13-2010 12:40 AM