p0101 + p0106 codes ?

jaytirbhaw · 12-13-2015, 07:44 PM

Brought the z out to get some runs in and attend a car meet since the weather is nice this weekend in the NE, driving along in 6th gear it bogs, service engine light comes on.

Got these two codes, p0101 + p0106 ?

Reset with obd and the car drives fine now. This ever happen to anyone ? Faulty MAF or MAP, dirty or something?

Is the map sensor on our cars actually used for anything other than eval? Thought i saw somewhere it is disabled in uprev?

EVOHUNTER · 12-14-2015, 08:59 AM

its probably pertaining to the p0101, the maf code. The other code was probably set off by the p0101.

I had this exact same problem, I found a bad connect in the maf wiring, where it was cut and spliced. When the cars idling, grab your bank 1 harness and shake it around. see if the code comes back on. if so, then you know its in the wiring.

could also be a dirty MAf.

jaytirbhaw · 12-14-2015, 09:42 AM

thanks ! will give it a try

jaytirbhaw · 12-14-2015, 02:47 PM

Wiggled it around and couldn't get the code to come back, weird. Going to try to clean the MAFS.

On a side note, anyone know what this aluminum foil looking heat wrap is called ? trying to find something a little prettier to replace it with

jwick · 12-14-2015, 02:49 PM

I don't know what that particular stuff is called but I used Thermo-Tec

Thermo-Tec Thermo-Sleeve 14010 - Free Shipping on Orders Over $99 at Summit Racing

jaytirbhaw · 12-14-2015, 05:55 PM

Quote:

Originally Posted by jwick

I don't know what that particular stuff is called but I used Thermo-Tec

Thermo-Tec Thermo-Sleeve 14010 - Free Shipping on Orders Over $99 at Summit Racing

thanks jwick, just ordered some !

jwick · 12-14-2015, 06:11 PM

Quote:

Originally Posted by jaytirbhaw

thanks jwick, just ordered some !

Unless you ordered it large enough to fit over the MAF plug you'll probably have to slice it open and zip tie. That's how I did all mine just so I knew it was wrapped tight and wouldn't move around.

jaytirbhaw · 12-14-2015, 06:12 PM

Quote:

Originally Posted by jwick

Unless you ordered it large enough to fit over the MAF plug you'll probably have to slice it open and zip tie. That's how I did all mine just so I knew it was wrapped tight and wouldn't move around.

yea i went ahead and got some zip ties as well

jwick · 12-14-2015, 07:02 PM

Quote:

Originally Posted by jaytirbhaw

yea i went ahead and got some zip ties as well

It's real easy to cut the string that holds it together. Just place a pair of scissors inside at the seam and pull firmly on the sleeve

tgastte · 05-17-2016, 10:39 AM

I just changed my MAP sensor to a new one, reset my ecm, but 3 days later my SES came back on and same code again P0106, now im lost what else do i need to replace or check.

jaytirbhaw · 06-03-2016, 12:30 PM

Quote:

Originally Posted by tgastte

I just changed my MAP sensor to a new one, reset my ecm, but 3 days later my SES came back on and same code again P0106, now im lost what else do i need to replace or check.

Late bump but .. Are you boosted ?

I bypassed the MAFs altogether by going with ECUTEK and tuning on speed density, upgraded my MAP sensor to an omni 4 bar. Haven't had any issues since

JSur · 07-06-2016, 08:30 PM

I'm boosted and I get the same code. I was told that my map sensor is only programmed to read vacuum up to 0. I need a tune to get it programmed to read boost. I'm most likely going with the EcuTek, although I heard uprev' new update that offers launch control is pretty compatible with EcuTek now. Map sensor codes could also be thrown due to a dirty throttle body

11' 370z TT

Zamfield · 07-06-2016, 09:59 PM

Sounds like an O2 sensor to me...

jaytirbhaw · 07-07-2016, 09:08 AM

Quote:

Originally Posted by JSur

I'm boosted and I get the same code. I was told that my map sensor is only programmed to read vacuum up to 0. I need a tune to get it programmed to read boost. I'm most likely going with the EcuTek, although I heard uprev' new update that offers launch control is pretty compatible with EcuTek now. Map sensor codes could also be thrown due to a dirty throttle body

11' 370z TT

Not sure if you can do this with Uprev, but with Ecutek you can get tuned by speed density. You'd have to upgrade your map sensor to an omni 4 bar

This eliminates the pesky MAF issues.

Chuck33079 · 07-07-2016, 09:11 AM

I got the MAP sensor code, and my tuner just turned it off in Uprev. No problems since.

12-13-2015, 07:44 PM	#1 (permalink)
jaytirbhaw Track Member Join Date: Dec 2009 Location: NYC Posts: 814 Drives: 350z HR , Nismo 370z Rep Power: 17	p0101 + p0106 codes ? Brought the z out to get some runs in and attend a car meet since the weather is nice this weekend in the NE, driving along in 6th gear it bogs, service engine light comes on. Got these two codes, p0101 + p0106 ? Reset with obd and the car drives fine now. This ever happen to anyone ? Faulty MAF or MAP, dirty or something? Is the map sensor on our cars actually used for anything other than eval? Thought i saw somewhere it is disabled in uprev? __________________ 2014 Nismo #350 , Built Motor, Top Mount Single Turbo .... 620 whp/ 500 lbs wtq 2012 Track/Drift Z, build coming soon. Build Thread - http://www.the370z.com/members-370z-...70z-build.html Last edited by jaytirbhaw; 12-13-2015 at 09:09 PM.

12-14-2015, 08:59 AM	#2 (permalink)
EVOHUNTER Track Member Join Date: Jul 2011 Location: Edmonton, Canada Posts: 681 Drives: BOOSTED3-7-0 Rep Power: 16	its probably pertaining to the p0101, the maf code. The other code was probably set off by the p0101. I had this exact same problem, I found a bad connect in the maf wiring, where it was cut and spliced. When the cars idling, grab your bank 1 harness and shake it around. see if the code comes back on. if so, then you know its in the wiring. could also be a dirty MAf. jaytirbhaw likes this. __________________

12-14-2015, 09:42 AM	#3 (permalink)
jaytirbhaw Track Member Join Date: Dec 2009 Location: NYC Posts: 814 Drives: 350z HR , Nismo 370z Rep Power: 17	thanks ! will give it a try __________________ 2014 Nismo #350 , Built Motor, Top Mount Single Turbo .... 620 whp/ 500 lbs wtq 2012 Track/Drift Z, build coming soon. Build Thread - http://www.the370z.com/members-370z-...70z-build.html

12-14-2015, 02:47 PM	#4 (permalink)
jaytirbhaw Track Member Join Date: Dec 2009 Location: NYC Posts: 814 Drives: 350z HR , Nismo 370z Rep Power: 17	Wiggled it around and couldn't get the code to come back, weird. Going to try to clean the MAFS. On a side note, anyone know what this aluminum foil looking heat wrap is called ? trying to find something a little prettier to replace it with __________________ 2014 Nismo #350 , Built Motor, Top Mount Single Turbo .... 620 whp/ 500 lbs wtq 2012 Track/Drift Z, build coming soon. Build Thread - http://www.the370z.com/members-370z-...70z-build.html

12-14-2015, 02:49 PM	#5 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465057	I don't know what that particular stuff is called but I used Thermo-Tec Thermo-Tec Thermo-Sleeve 14010 - Free Shipping on Orders Over $99 at Summit Racing jaytirbhaw likes this. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

05-17-2016, 10:39 AM	#10 (permalink)
tgastte Base Member Join Date: May 2016 Location: California Posts: 8 Drives: 12 370z 6mt Rep Power: 10	I just changed my MAP sensor to a new one, reset my ecm, but 3 days later my SES came back on and same code again P0106, now im lost what else do i need to replace or check. jaytirbhaw likes this.

07-06-2016, 08:30 PM	#12 (permalink)
JSur Base Member Join Date: Mar 2016 Location: Orlando Posts: 84 Drives: 2011 370z TT Rep Power: 10	I'm boosted and I get the same code. I was told that my map sensor is only programmed to read vacuum up to 0. I need a tune to get it programmed to read boost. I'm most likely going with the EcuTek, although I heard uprev' new update that offers launch control is pretty compatible with EcuTek now. Map sensor codes could also be thrown due to a dirty throttle body 11' 370z TT

07-06-2016, 09:59 PM	#13 (permalink)
Zamfield Base Member Join Date: Apr 2014 Location: WV Posts: 39 Drives: 09 Silver 370z S/T Rep Power: 12	Sounds like an O2 sensor to me...

07-07-2016, 09:11 AM	#15 (permalink)
Chuck33079 A True Z Fanatic Join Date: Nov 2011 Location: Houston Posts: 12,265 Drives: 2011 370ztt Rep Power: 29539	I got the MAP sensor code, and my tuner just turned it off in Uprev. No problems since. jaytirbhaw likes this. __________________ 2011 MB Touring-Sport-6sp-Nav/GTM TT/FI TT TDX/JTran/Kosmic/Eibach/Hotchkis/SPC/CSF/RPS/SoThatsWhereAllMyMoneyWent

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Code P0106	megalapagas	Engine & Drivetrain	21	06-09-2021 06:55 PM
P0106 - MAP Sensor trouble?	x2o	Forced Induction	3	08-31-2020 02:08 PM
Codes and more Codes? now no start...	instroke	Forced Induction	15	10-15-2015 10:51 PM
Code P0106	George28	Engine & Drivetrain	5	06-15-2015 08:09 PM
P0106 P006a	W.O.W. 370Z	Tuning	3	10-29-2012 09:51 PM