Nissan 370Z Forum

Nissan 370Z Forum (http://www.the370z.com/)
-   Forced Induction (http://www.the370z.com/forced-induction/)
-   -   Stillen Air to Air setup (http://www.the370z.com/forced-induction/104308-stillen-air-air-setup.html)

JWillis72 12-08-2015 03:36 PM

Thanks guys.


Sent from my iPhone using Tapatalk

jwick 12-08-2015 03:41 PM

:tiphat:

TopgunZ 12-08-2015 03:49 PM

Here are the steel mesh ones. Save shipping cost and have them today.

Speed by Spectre 3995 - Oil Breather Cap | O'Reilly Auto Parts

JWillis72 12-08-2015 07:31 PM

I don't have a O'Reilly near me but I found a found a local place that has them. I have new MAF extensions from Stillen being delivered tomorrow but don't think they will change anything. I'm running out of ideas but trying not to give up.


Sent from my iPhone using Tapatalk

TopgunZ 12-08-2015 09:28 PM

Like I said. Put the old pipe back on. You won't have to take anything off to try it. It will take minutes and rule out so much.

JWillis72 12-09-2015 04:59 PM

We cut the old pipe for part of this one. Do you still have the vacuum like on the back of the Stillen manifold?


Sent from my iPhone using Tapatalk

EVOHUNTER 12-09-2015 05:14 PM

Quote:

Originally Posted by JWillis72 (Post 3364174)
We cut the old pipe for part of this one. Do you still have the vacuum like on the back of the Stillen manifold?


Sent from my iPhone using Tapatalk

I have 4 lines going into the manifold, one right from booster to manifold other 2 too valve covers, and one goes to my purge sol.

I kept the same setup as stillen, only thing changed was the one line that goes into the coupler in the blower and the other side hooks up to your bpv.

instead of going into the coupler, sasha put it into the intake right after the filter.

TopgunZ 12-09-2015 09:23 PM

Evo. That coupler port is still the same as stillen did it. Its still pre blower. That's the only way to recirc.

JWillis72 12-10-2015 06:27 PM

It's all back together and still not acting right. MAF voltage is still off and the AFR on one bank is reading lower than the other after it runs a bit. We are to try the swapping MAFs then swapping wire again but last time the numbers stayed with the pipe. They are also going to get it back on the lift to check for exhaust leaks.

jwick 12-11-2015 05:15 PM

Have they smoke or soap tested it?

JWillis72 12-13-2015 06:03 PM

Quote:

Originally Posted by jwick (Post 3365941)
Have they smoke or soap tested it?


Yes, they have smoked it a couple times. I'm in Ohio until tomorrow night but they seem to have had some luck SD tuning it. The shop is telling me if things go well in the morning that it could be in the dyno tomorrow but at this point I will believe it when I see it.


Sent from my iPhone using Tapatalk

TopgunZ 12-14-2015 11:44 AM

Waiting for the good news on the SD tune and that 500+ number!!!

DatsunFTW 12-14-2015 04:11 PM

Let me know when you're at the shop this week. I'll come by :)

JWillis72 12-14-2015 04:25 PM

Quote:

Originally Posted by DatsunFTW (Post 3367648)
Let me know when you're at the shop this week. I'll come by :)


Fuckers isn't answering me because I'm in Ohio! I'm at the airport now and will be there to see him when he opens!


Sent from my iPhone using Tapatalk

JWillis72 12-15-2015 04:20 PM

They can't tell me if it can be tuned at this point but he said I would know tonight. If the answer is no I'm done and the car is going back to how it was, well close as we can get it. Its a track car that has kept me from the track for six months and I'm over it. One way or the other this has to end and it has to end now.


All times are GMT -5. The time now is 05:02 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2