Possible fueling issues?

DIGItonium · 04-10-2015, 09:36 AM

Yea, it'll be something to look at when I pull stuff apart to change the spark plugs.

BTW... should I monitor AFR from the CAN bus data, or should I get an aftermarket gauge and sensor? If I can rely on the CAN bus data, then it'll save a lot of wiring work. I may get a digital multi gauge with ODB2 input.

Chuck33079 · 04-10-2015, 09:39 AM

Quote:

Originally Posted by DIGItonium

Yea, it'll be something to look at when I pull stuff apart to change the spark plugs.

BTW... should I monitor AFR from the CAN bus data, or should I get an aftermarket gauge and sensor? If I can rely on the CAN bus data, then it'll save a lot of wiring work. I may get a digital multi gauge with ODB2 input.

I'd always trust an aftermarket wideband over the factory O2 sensors.

jwick · 04-10-2015, 09:47 AM

Quote:

Originally Posted by Chuck33079

I'd always trust an aftermarket wideband over the factory O2 sensors.

EVOHUNTER · 04-11-2015, 10:54 AM

Get a wideband bro, there actually really easy to wire.

My wideband has help me diagnose 99% of my problems.

Also, test your vacuum, maybe you have a leak somewhere.

DIGItonium · 04-14-2015, 04:33 PM

Quote:

Originally Posted by EVOHUNTER

Get a wideband bro, there actually really easy to wire.

My wideband has help me diagnose 99% of my problems.

Also, test your vacuum, maybe you have a leak somewhere.

Thanks. So is better to get a wideband sensor and AFR gauge versus pulling AFR Bank1 and Bank2 using Cipher?

Yea, hopefully I can get a hold a smoke machine. I'll get it done after maintenance work.

jwick · 04-14-2015, 05:00 PM

Quote:

Originally Posted by DIGItonium

Thanks. So is better to get a wideband sensor and AFR gauge versus pulling AFR Bank1 and Bank2 using Cipher?

Yes. Aftermarket AFR is better than trusting the numbers from Cipher

phunk · 04-14-2015, 05:33 PM

Do any of the 370z even have factory widebands? I remember a couple years of the 350z did for a minute, but then they ditched it.

If the factory o2 sensors are not widebands, the A/F reading anywhere about a half point away from stoich is worthless data.

My 2009 uses standard narrowband o2s.

COSMO · 04-14-2015, 08:52 PM

Do some fuel logs but I can almost guarantee you that one or both of your gtm exhaust manifolds are Cracked causing a Rich condition.... Ask me how I know...

DIGItonium · 04-14-2015, 11:55 PM

Quote:

Originally Posted by COSMO

Do some fuel logs but I can almost guarantee you that one or both of your gtm exhaust manifolds are Cracked causing a Rich condition.... Ask me how I know...

I was going to ask you the very same question after asking you about symptoms. :P Do you hear any high pitched whistling? I've been hearing the faint whistle for the past year, and it seems like it's on the passenger side. Evidently, it is the same one that has a minor oil leak, but not enough to drip. There's no blue smoke. The PCV hose and vacuum line to the throttle has oil residue as well. The driver side is clean. I can only imagine what it'll be like after removing the throttle bodies.

I'll have the exhaust manifolds checked the next time the car gets on a lift.

Quote:

Originally Posted by phunk

Do any of the 370z even have factory widebands? I remember a couple years of the 350z did for a minute, but then they ditched it.

I remembered this being discussed at one time, and I thought that's what people concluded - that the cars come stock with widebands. I was just curious to see the wide band sensor parameters in Cipher. If that's the case, then I'll consider getting a sensor makeover at some point to go with the digital multi gauges from Zada Tech. Phew... gonna be pricey.

jwick · 04-15-2015, 08:03 AM

Just buy a digital Innovate. $180 and your set.

DIGItonium · 04-15-2015, 08:35 AM

Quote:

Originally Posted by jwick

Just buy a digital Innovate. $180 and your set.

One for each side?

EVOHUNTER · 04-15-2015, 08:36 AM

Look up EVAP diy smoke machine, you can make one for 10$.

Hook her up to a vacuum line, and watch for smoke

jwick · 04-15-2015, 08:54 AM

Quote:

Originally Posted by DIGItonium

One for each side?

You can do that but I'd probably look for a single readout that will read both gauges. With the LC-1/2 you would have to run a second gauge. Most people just monitor one bank. I recommend bank 1 (passenger side) because it seems to run slightly leaner than bank 2. If you don't have the bung in either the downpipe or lead pipe just have a bung welded into the lead pipe of the FI exhaust. A muffler shop should be able to do that pretty quickly at a low cost.

Chuck - I can't recall off the top of my head, but where's your AFR O2 sensor located?

Edit - Innovate makes a single gauge dual wideband but I can't seem to find it any place but eBay for instock purchase so it might be discontinued.

http://www.innovatemotorsports.com/products/dlg1.php

This is the one I run LC-1 with the DB gauge

http://www.innovatemotorsports.com/products/db.php

Chuck33079 · 04-15-2015, 08:56 AM

Quote:

Originally Posted by jwick

You can do that but I'd probably look for a single readout that will read both gauges. With the LC-1/2 you would have to run a second gauge. Most people just monitor one bank. I recommend bank 1 (passenger side) because it seems to run slightly leaner than bank 2. If you don't have the bung in either the downpipe or lead pipe just have a bung welded into the lead pipe of the FI exhaust. A muffler shop should be able to do that pretty quickly at a low cost.

Chuck - I can't recall off the top of my head, but where's your AFR O2 sensor located?

Kosmic welded a new bung in one of the downpipes.

jwick · 04-15-2015, 09:01 AM

Quote:

Originally Posted by Chuck33079

Kosmic welded a new bung in one of the downpipes.

Before install. That's right.

DIG - I would recommend tapping the lead pipe on the FI exhaust over trying to tap the downpipe in the installed condition.

04-10-2015, 09:36 AM	#16 (permalink)
DIGItonium A True Z Fanatic Join Date: Jan 2009 Location: Kansas Posts: 3,800 Drives: 09 Z34-TT 6MT Rep Power: 42	Yea, it'll be something to look at when I pull stuff apart to change the spark plugs. BTW... should I monitor AFR from the CAN bus data, or should I get an aftermarket gauge and sensor? If I can rely on the CAN bus data, then it'll save a lot of wiring work. I may get a digital multi gauge with ODB2 input. __________________

04-11-2015, 10:54 AM	#19 (permalink)
EVOHUNTER Track Member Join Date: Jul 2011 Location: Edmonton, Canada Posts: 681 Drives: BOOSTED3-7-0 Rep Power: 14	Get a wideband bro, there actually really easy to wire. My wideband has help me diagnose 99% of my problems. Also, test your vacuum, maybe you have a leak somewhere. __________________

04-14-2015, 05:33 PM	#22 (permalink)
phunk A True Z Fanatic Join Date: Mar 2009 Location: Chicago Posts: 3,655 Drives: 370 Rep Power: 944523	Do any of the 370z even have factory widebands? I remember a couple years of the 350z did for a minute, but then they ditched it. If the factory o2 sensors are not widebands, the A/F reading anywhere about a half point away from stoich is worthless data. My 2009 uses standard narrowband o2s. __________________ Charles @ CJ Motorsports : Website \| Facebook \| Instagram \| YouTube Home of the 9 second, stock longblock, stock drivetrain 6MT 370z. 9.91 @ 142mph

04-14-2015, 08:52 PM	#23 (permalink)
COSMO A True Z Fanatic Join Date: Dec 2012 Location: FL Posts: 1,816 Drives: 2012 Touring GTM TT Rep Power: 19	Do some fuel logs but I can almost guarantee you that one or both of your gtm exhaust manifolds are Cracked causing a Rich condition.... Ask me how I know... EVOHUNTER likes this.

04-15-2015, 08:03 AM	#25 (permalink)
jwick A True Z Fanatic Join Date: Dec 2010 Location: Houston Posts: 14,532 Drives: '10 G37 6MT Rep Power: 2465056	Just buy a digital Innovate. $180 and your set. __________________ '10 G37T 6MT Graphite/Graphite - BP - G37T Build

04-15-2015, 08:36 AM	#27 (permalink)
EVOHUNTER Track Member Join Date: Jul 2011 Location: Edmonton, Canada Posts: 681 Drives: BOOSTED3-7-0 Rep Power: 14	Look up EVAP diy smoke machine, you can make one for 10$. Hook her up to a vacuum line, and watch for smoke DIGItonium likes this. __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Having some issues with my 7AT	falconfixer	Engine & Drivetrain	21	04-22-2013 02:17 PM
GTM issues	spawn350	Forced Induction	80	09-27-2012 08:21 PM
MBC issues?	AWX Z34	Forced Induction	7	04-06-2012 10:13 PM
thinking of buying 370z, then GTM turbo's , but overheat issues,oil issues ??	Christopher	Nissan 370Z General Discussions	19	10-16-2009 03:55 PM
Initial Z issues that are now non-issues......	cave vulture	Nissan 370Z General Discussions	1	09-06-2009 10:19 PM