Carbon Fiber front fascia?

NYBladeZ

I hope so, I'm patiently waiting to see how much weight it I actually shave off. Though honestly I did it for the unique look than any major weight reductions. Anyone know where I can get an overlay for the rear quarter panel in CF?

__________________
2009 Carbon Fiber/Red 370z aka Trish: Sports Package, Meisterschaft full catback, Fast Intentions Longtube Headers, Injen Long Tube Intakes, UpRev Tune: Sold
2008 Lotus Exige S Club Racer aka Bella, always leaves me smiling

nogoodname

mmmm... i dont think you can....lol

think of it like this... the fenders are made from steel
(only hatch, door skin and hood are aluminum)

CF is lighter than aluminum... so there's definitely a savings

Modshack

Actually the Hood, Doors and hatch are aluminum......

Roof is steel....My Auto-X numbers stuck real good up there..

__________________

Steal my car! (SOLD)...Now Porsche Cayman S
Oil Cooler DIY: Here!

nogoodname

my bad.... i meant that...lol

door skin is aluminum

Auto_Infantry

I agree, carbon fiber is very strong when stretching and bending, but weak when compressed or exposed to high shock.

But, take for example a CF strut bar or wing, it won't bend or flex easily, but when hit with something at high speed or if something heavy dropped on it, it will crack. The high shock or impact will crack carbon fiber, not necessarily break it, but cause structural failure in which the carbon will be able to be bent or stretched more so then when not cracked.The crack will only get bigger and spider if more flexing and bending are applied to the piece. Once Carbon fiber is cracked, typically it is rendered useless. Even when repaired, it will never be the same strength as it was before.

As for applications of typical automotive carbon fiber, you won't need multiple layers necessarily. Typically you have different types of carbon for different applications. Most common in the auto industry are as follow: Hand Laid;made by layering up carbon fiber in a similar process to fiberglass, multiple coats of resin/material are laid to create a finished product often made with a mold, Vacuum infusion; a single layer (sometimes more) of carbon fiber material, laid into a mold and sealed with a plastic sheet (often times called "bagged," one end of a tube has resin and the other a vacuum in which the resin is sucked in over the carbon fiber allowing it to have minimal usage of resin (which causes weight and structural rigidity loss in cf) yet enough to make a strong durable part, lastly, we have Pre-Preg carbon or what some people call "Dry Carbon" not to be confused with the "Dry carbon look" where a flat clear is sprayed on to the finished product. Pre-Preg carbon is infused at the materials manufacturing plant with temperature curing resin. It has resin already bonded with the cf and must be stored in a container below freezing (don't remember the numbers off the top of my head). When applied to a mold, it is "baked" in huge ovens (again don't remember the numbers which can vary) which will cause the resin which it was impregnated with to begin its curing process. These are just a few of the different types of CF you will find.

The point of Carbon fiber is to create a strong rigid piece that also eliminates the need of multiple layering such as is found in Fiberglass or FRP which causes weight a majority of the weight. For example a hatch from a car can weigh in at about 50+ lbs. At hand laid levels you can cut that weight in half so about 25lbs. Vacuum Infusion we can achieve a little more then half or 3/4 of the hand laid weight so about 14-16 lbs. With Dry Carbon you can achieve a little less then vacuum infusion, about 10-13 lbs.

kenchan

something to think about when boarding the upcoming Boeing 787....
toray's doing billions of dollars business with them for all the large CF bits.

Auto_Infantry

The kind of CF work that is used in planes is not quite the same as in the Auto Industry, Especially when making CF sub-frame pieces and such. The pieces would look more like the CF drive-shafts of the Z. It won't look pretty with all the weave and crazy patterns. Some pieces will look like that but some parts are Carbon Fiber yet don't even look like what most of us are used to. Just look under your Z and you'll see what I'm talking about. Carbon can be used in different applications but what I mentioned is most common in the Automotive Industry. I'm working on a thread to help everyone out and learn about CF and hopefully i'll be done this week with it. Hopefully it will help many of the buyers get educated on what they are buying.