Modified B Pillar

Ztoon · 06-24-2010, 03:47 PM

209Z · 06-24-2010, 06:09 PM

so what size do i need if i want to hit up the whole inside trim?

Ztoon · 06-24-2010, 06:32 PM

Give a couple inches over for each piece. Keep in mind pattern weave direction. More complex pieces, allow for 2 tries, like I did for the shift ring.
(don't know why the frikkin pictures wouldn't load, check out my album).
I wouldn't by any of their applicators or cleaning solutions. Just rubbing alcohol to clean, an' your good to go.

209Z · 06-24-2010, 06:33 PM

what about the 3m tire spray?

Ztoon · 06-24-2010, 06:55 PM

Hmmm, don't know. Basically you want to remove any oils that could reduce adhesion. Tire sprays restore lustre, so it may contain silicone.

RedNismo · 06-25-2010, 12:02 AM

Dish liquid thinned out with water is the best. That's what I'll use to wash off the wax from my roof before installing the Ni-Doc.

zZSoCalZz · 06-29-2010, 12:23 PM

Roof looks amazing! Can't wait til my supplies come. Did you use heat gun or just a house hold blow dryer?

RedNismo · 06-29-2010, 01:56 PM

Quote:

Originally Posted by zZSoCalZz

Roof looks amazing! Can't wait til my supplies come. Did you use heat gun or just a house hold blow dryer?

It takes not much heat. So i guess blow dryer would work. I used a heat gun. It's faster and easier to control. Just make sure you don't pull on vinyl too much while it is in the soft state (hot). The vinyl would stretch just a tiny bit in a certain spot and create minor discoloration. unfortunately, I found this out the hard way. I have a little bit of this issue on my roof. But I am not going to waste 150 bucks worth of di noc and redo it though.

By the way, I didn't have to use any heat for the pillars. I only had to use heat on the roof installation.

zZSoCalZz · 06-29-2010, 02:16 PM

Quote:

Originally Posted by RedNismo

It takes not much heat. So i guess blow dryer would work. I used a heat gun. It's faster and easier to control. Just make sure you don't pull on vinyl too much while it is in the soft state (hot). The vinyl would stretch just a tiny bit in a certain spot and create minor discoloration. unfortunately, I found this out the hard way. I have a little bit of this issue on my roof. But I am not going to waste 150 bucks worth of di noc and redo it though.

By the way, I didn't have to use any heat for the pillars. I only had to use heat on the roof installation.

Thanks for the heads up.

TacoZ · 06-29-2010, 12:52 PM

Very nice! I like!

wishihadnav · 06-29-2010, 01:03 PM

Here's a DIY for this mod...ricing out volume 1 i believe..haha

How to rice out your Z to the max vol.1 <Carbon Fiber film your B-pillars>

zZSoCalZz · 06-29-2010, 01:34 PM

Quote:

Originally Posted by wishihadnav

Here's a DIY for this mod...ricing out volume 1 i believe..haha

How to rice out your Z to the max vol.1 <Carbon Fiber film your B-pillars>

1. Required tools are [ scissors, 3M Dinoc Carbon Fiber film, marker, hair dryer ]

Nice he used hair dryer.

RedNismo · 06-29-2010, 02:12 PM

Quote:

Originally Posted by wishihadnav

Here's a DIY for this mod...ricing out volume 1 i believe..haha

How to rice out your Z to the max vol.1 <Carbon Fiber film your B-pillars>

"Rice Out" I am offended. lol

kenchan · 06-29-2010, 02:15 PM

i dont have this exact sheet, but i have something similar that shrinks and adheres with heat i bought long time ago. it's just a simulated CF.

im going to make me a cutout for the steering wheel volume up/down trim.

it's a small triangular shaped thing that looks out of place without some kind of trim.

Reaper42 · 06-29-2010, 05:30 PM

I really like this!

06-24-2010, 03:47 PM	#1 (permalink)
Ztoon Track Member Join Date: Aug 2009 Location: B.C. Posts: 578 Drives: '09 370a7 Rep Power: 26	__________________ Stillen G3\|CBE\|ground kit, F.I. H.F.C., C.F. fangs\|mirrors\|pillars, Hotchkis, SSR Type-F, RE-11, UpRev, BC BR coilovers 15% tint, LED black hdlts, color match handles, Dynamat, tail lt. tint, Mines C.F. frt. lip\|rear spoiler, Amuse rear,skirts, vented fenders, c.f. vented hood, gloss blk. roof

06-24-2010, 06:09 PM	#2 (permalink)
209Z A True Z Fanatic Join Date: Mar 2009 Location: Stockton, Cali (209) Posts: 1,058 Drives: 09 370z Rep Power: 279	so what size do i need if i want to hit up the whole inside trim? __________________ Team Blur My Build Thread Fast Intentions\|KWS\|BERK\|Carbon Fiber Element\| SEIBON\|Memphis Car Audio\| Status Autoworks\|Lusso Forged\|Autohaus\|PWJDM\|SPC

06-24-2010, 06:32 PM	#3 (permalink)
Ztoon Track Member Join Date: Aug 2009 Location: B.C. Posts: 578 Drives: '09 370a7 Rep Power: 26	Give a couple inches over for each piece. Keep in mind pattern weave direction. More complex pieces, allow for 2 tries, like I did for the shift ring. (don't know why the frikkin pictures wouldn't load, check out my album). I wouldn't by any of their applicators or cleaning solutions. Just rubbing alcohol to clean, an' your good to go. __________________ Stillen G3\|CBE\|ground kit, F.I. H.F.C., C.F. fangs\|mirrors\|pillars, Hotchkis, SSR Type-F, RE-11, UpRev, BC BR coilovers 15% tint, LED black hdlts, color match handles, Dynamat, tail lt. tint, Mines C.F. frt. lip\|rear spoiler, Amuse rear,skirts, vented fenders, c.f. vented hood, gloss blk. roof

06-24-2010, 06:33 PM	#4 (permalink)
209Z A True Z Fanatic Join Date: Mar 2009 Location: Stockton, Cali (209) Posts: 1,058 Drives: 09 370z Rep Power: 279	what about the 3m tire spray? __________________ Team Blur My Build Thread Fast Intentions\|KWS\|BERK\|Carbon Fiber Element\| SEIBON\|Memphis Car Audio\| Status Autoworks\|Lusso Forged\|Autohaus\|PWJDM\|SPC

06-24-2010, 06:55 PM	#5 (permalink)
Ztoon Track Member Join Date: Aug 2009 Location: B.C. Posts: 578 Drives: '09 370a7 Rep Power: 26	Hmmm, don't know. Basically you want to remove any oils that could reduce adhesion. Tire sprays restore lustre, so it may contain silicone. __________________ Stillen G3\|CBE\|ground kit, F.I. H.F.C., C.F. fangs\|mirrors\|pillars, Hotchkis, SSR Type-F, RE-11, UpRev, BC BR coilovers 15% tint, LED black hdlts, color match handles, Dynamat, tail lt. tint, Mines C.F. frt. lip\|rear spoiler, Amuse rear,skirts, vented fenders, c.f. vented hood, gloss blk. roof

06-25-2010, 12:02 AM	#6 (permalink)
RedNismo Base Member Join Date: Jan 2010 Location: Glendale CA Posts: 92 Drives: 09 Nismo Z #389 RD Rep Power: 16	Dish liquid thinned out with water is the best. That's what I'll use to wash off the wax from my roof before installing the Ni-Doc. __________________ 2003 Skyline 350GT--Tein Suspension, NRG Strut bar, Nismo CAI w/bypass, JDM emblems, Nismo Graphics... 2009 Nismo Z34 #389-- Clear Bra

06-29-2010, 12:23 PM	#7 (permalink)
zZSoCalZz Base Member Join Date: May 2010 Location: Los Angeles Posts: 176 Drives: in traffic! Rep Power: 16	Roof looks amazing! Can't wait til my supplies come. Did you use heat gun or just a house hold blow dryer? __________________ 2009 MB: Stillen G3 Intake // Customized illuminated kickplates frost blue Z //

06-29-2010, 12:52 PM	#10 (permalink)
TacoZ Enthusiast Member Join Date: Dec 2008 Location: Southern California Posts: 319 Drives: 09 370Z PW M6 Rep Power: 17	Very nice! I like!

06-29-2010, 01:03 PM	#11 (permalink)
wishihadnav A True Z Fanatic Join Date: Nov 2009 Location: 90090 Posts: 1,851 Drives: Force Fed Nismo Rep Power: 184	Here's a DIY for this mod...ricing out volume 1 i believe..haha How to rice out your Z to the max vol.1 <Carbon Fiber film your B-pillars>

06-29-2010, 02:15 PM	#14 (permalink)
kenchan A True Z Fanatic Join Date: Aug 2009 Location: N/A Posts: 76,801 Drives: N/A Rep Power: 141522	i dont have this exact sheet, but i have something similar that shrinks and adheres with heat i bought long time ago. it's just a simulated CF. im going to make me a cutout for the steering wheel volume up/down trim. it's a small triangular shaped thing that looks out of place without some kind of trim.

06-29-2010, 05:30 PM	#15 (permalink)
Reaper42 A True Z Fanatic Join Date: May 2009 Location: Chicago, IL Posts: 1,030 Drives: GetLucky370 Rep Power: 19	I really like this! __________________ Sponsor roll call: Get Lucky Brand \| TOYO TIRES \| Element Graphics \| Unique Fabrication Follow on fb- Jon Sackett and Instagram @GetLucky370 GetLucky370

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Genetically modified rice...	nuTinmuch	Other Vehicles	10	04-29-2010 06:01 PM
As-is - un-modified....not for track ........	cave vulture	Nissan 370Z General Discussions	43	06-09-2009 05:09 PM
Hot pics! S30 and Z34 Black 370Z with modified Datsun 280Z	370ZRR	Nissan 370Z Photos / Spyshots / Video / Media Gallery	23	04-08-2009 06:18 PM
Modified Mag (March Issue): 370Z mod article	subterfuge242	Nissan 370Z General Discussions	1	02-16-2009 11:38 PM
Modified Mag Article March 2009	WShade	Nissan 370Z Photos / Spyshots / Video / Media Gallery	12	02-02-2009 06:59 PM