My AeroJacket Duckbill Spoiler Install

pbhakta · 03-30-2016, 10:04 AM

I just finally got around to getting my duckbill spoiler installed on my car and let me tell you how much of a pain it was to actually do this myself. The worse part of this install was trying to remove the old spoiler double sided tape from the car. It took me a couple of weeks to get through this install as I have 2 kids under 2 years old, so that means I get to spend about 2 hours a week on it nightly.

I started with taking off my old spoiler. Worst part of the entire process up front. I already had a sport spoiler so I was going to use the original holes similar to a DIY thread on here for the duckbill. I followed this thread as my guide, but did deviate a bit on some pieces. DIY AERO JACKET III Wing install (short version) for KaienZ34

I then put some zip ties down into the holes already in the car with some "duck" tape facing up so it would stick to the spoiler when I fitted it to the car. For the most part the molded lines seem to match up so I could drill holes into the spoiler where the zip tie heads lined up and put the original clips into the spoiler.

I then drilled the holes for the clips and epoxied them in place again similar to the DIY for the duckbill spoiler.

The last step for me was to put the spoiler on with 3M double sided tape.

Here is the final look. I had just added EVO-R side blades as well and over all I am finally happy with the look of my car all around with CF accent on the front lip, blades, rear diffuser and spoiler.

For comparison here is my car before the blades and spoiler.

1cintron · 03-30-2016, 10:21 AM

Looks amazing!!! How is the fitment of your DF1 diffuser?

pbhakta · 03-30-2016, 10:31 AM

Quote:

Originally Posted by 1cintron

Looks amazing!!! How is the fitment of your DF1 diffuser?

Thanks. The fitment was actually pretty good. Super easy to install as well.

I have another thread just for the DF1 install if you wanted to take a closer look.

My Install of AeroJacket DF1 Diffuser

1cintron · 03-30-2016, 12:07 PM

Quote:

Originally Posted by pbhakta

Thanks. The fitment was actually pretty good. Super easy to install as well.

I have another thread just for the DF1 install if you wanted to take a closer look.

My Install of AeroJacket DF1 Diffuser

u da man! thanks bud!

m3chhawk · 03-30-2016, 10:21 PM

Dat XC90 doe

pbhakta · 03-31-2016, 08:32 AM

Quote:

Originally Posted by m3chhawk

Dat XC90 doe

Dayamm...you got a good eye...especially since it was just photobombing in one of the pics...

You can see my son trying to get into the "new car"...he doesnt care about the Z anymore...

Breadz · 04-01-2016, 07:01 PM

Looks good man, our cars are pretty similar once my f14s come in , bronze tho

axmea? · 04-01-2016, 07:45 PM

Good job! Now go back have fun with the Z and raise the best kids you could ever have. And take pics without your shadow. Pics with outlines of people don't go well with our Zs.

axmea? · 04-01-2016, 07:50 PM

Forgot to ask, did you use all the holes? If not did you seal?

kenney255 · 04-01-2016, 10:03 PM

when i looked online it said the duckbill was for the 09-12 , i have a 2016 do you know if there was any changes in the trunk from then ? thanks in advance

Jayhovah · 04-02-2016, 01:47 PM

Quote:

Originally Posted by kenney255

when i looked online it said the duckbill was for the 09-12 , i have a 2016 do you know if there was any changes in the trunk from then ? thanks in advance

no changes.

pbhakta · 04-04-2016, 09:01 AM

Quote:

Originally Posted by axmea?

Forgot to ask, did you use all the holes? If not did you seal?

I did not use the outside two holes. I did seal them with a latex based sealant DAP 230.

fury370 · 06-15-2016, 02:38 PM

Looks awesome!

Question for you and sorry for thread jacking if it is. But since this has been pretty recent, how was your dealings with Aero jacket? I've ordered the same spoiler from them May 4th, and have yet to hear anything back from them, even after multiple emails sent to them.

pbhakta · 06-15-2016, 02:58 PM

Quote:

Originally Posted by fury370

Looks awesome!

Question for you and sorry for thread jacking if it is. But since this has been pretty recent, how was your dealings with Aero jacket? I've ordered the same spoiler from them May 4th, and have yet to hear anything back from them, even after multiple emails sent to them.

I actually bought the spoiler from another forum member so it wasnt through aerojacket. I have ordered parts from them about year or two ago and did receive my products in a timely manner. I had ordered the DF1 Diffuser, Side Blades and rear spats all at once and everything came as they had said. I only ended up using the Diffuser though.

Gluck I hope everything works out for you.

BboyZ · 06-15-2016, 03:30 PM

Fitment really looks good to me. Congrats.

03-30-2016, 10:04 AM	#1 (permalink)
pbhakta Enthusiast Member Join Date: Dec 2011 Location: Kansas City Posts: 333 Drives: 11 GM 370z T/S 6MT Rep Power: 13	My AeroJacket Duckbill Spoiler Install I just finally got around to getting my duckbill spoiler installed on my car and let me tell you how much of a pain it was to actually do this myself. The worse part of this install was trying to remove the old spoiler double sided tape from the car. It took me a couple of weeks to get through this install as I have 2 kids under 2 years old, so that means I get to spend about 2 hours a week on it nightly. I started with taking off my old spoiler. Worst part of the entire process up front. I already had a sport spoiler so I was going to use the original holes similar to a DIY thread on here for the duckbill. I followed this thread as my guide, but did deviate a bit on some pieces. DIY AERO JACKET III Wing install (short version) for KaienZ34 I then put some zip ties down into the holes already in the car with some "duck" tape facing up so it would stick to the spoiler when I fitted it to the car. For the most part the molded lines seem to match up so I could drill holes into the spoiler where the zip tie heads lined up and put the original clips into the spoiler. I then drilled the holes for the clips and epoxied them in place again similar to the DIY for the duckbill spoiler. The last step for me was to put the spoiler on with 3M double sided tape. Here is the final look. I had just added EVO-R side blades as well and over all I am finally happy with the look of my car all around with CF accent on the front lip, blades, rear diffuser and spoiler. For comparison here is my car before the blades and spoiler. JARblue, Gilianz, axmea? and 10 others like this. __________________ 2011 6MT 370Z Gun Metallic :: Stillen G3 CAI :: Swift Springs :: EvoR :: JWM LEDs :: TommyKaira :: Forgestar F14 :: Motordyne Shockwave))) E370 :: CS Spec-Me Lip :: AeroJacket Last edited by pbhakta; 03-30-2016 at 10:35 AM.

03-30-2016, 10:21 AM	#2 (permalink)
1cintron Base Member Join Date: Mar 2013 Location: Dayton, OH Posts: 116 Drives: 370z Rep Power: 12	Looks amazing!!! How is the fitment of your DF1 diffuser? pbhakta likes this.

03-30-2016, 10:21 PM	#5 (permalink)
m3chhawk Track Member Join Date: Sep 2012 Location: Kansas City Posts: 878 Drives: '11 370Z SPT 6MT BLK Rep Power: 24	Dat XC90 doe pbhakta likes this. __________________ F.I. CF CBE \| Avant Garde M310 \| BC BR's \| ONEighty \| Status \| EvoR \| Stillen \| Whiteline \| B&M \| Bespoke Details Boosted Performance \| Precision Turbo \| Tial \| HKS \| Innovate Motorsports \| Bosch \| Treadstone \| Walbro \| UpRev \| Depo

04-01-2016, 07:01 PM	#7 (permalink)
Breadz Base Member Join Date: Jan 2015 Location: Clovis Cali Posts: 240 Drives: 12 370z sport 6mt GM Rep Power: 10	Looks good man, our cars are pretty similar once my f14s come in , bronze tho pbhakta likes this. __________________ Fast Intentions Non res CF, CF Duckbill, Stillen G3, Fujimura Diffuser, Swift Springs, 180 Headlights, Forgestar F14Bronze

04-01-2016, 07:45 PM	#8 (permalink)
axmea? A True Z Fanatic Join Date: Apr 2012 Location: SoCal Posts: 6,233 Drives: WELL ZED PW 6MT Rep Power: 53241	Good job! Now go back have fun with the Z and raise the best kids you could ever have. And take pics without your shadow. Pics with outlines of people don't go well with our Zs. __________________ >MyZ's Album< NISMO Convert/ECUTEK/Takeda CAI/F.I. HFC NR CB Carbon/F.I. 34 Row Oil Cooler/4.08 Final Drive /Powertrix+Swifts/Hotchkis/SPL/Whiteline/TWM/Zoom Engineering/EVO-R/AeroJacket Vented CF Fenders + CF Spoiler/Avant Garde-WORK/NST/Morimoto Halo/STi Clear Lenses/Carbon Signal Automotive/RJM Performance/ZSpeed Clutch Flywheel CSC delete Last edited by axmea?; 04-01-2016 at 07:48 PM.

04-01-2016, 07:50 PM	#9 (permalink)
axmea? A True Z Fanatic Join Date: Apr 2012 Location: SoCal Posts: 6,233 Drives: WELL ZED PW 6MT Rep Power: 53241	Forgot to ask, did you use all the holes? If not did you seal? __________________ >MyZ's Album< NISMO Convert/ECUTEK/Takeda CAI/F.I. HFC NR CB Carbon/F.I. 34 Row Oil Cooler/4.08 Final Drive /Powertrix+Swifts/Hotchkis/SPL/Whiteline/TWM/Zoom Engineering/EVO-R/AeroJacket Vented CF Fenders + CF Spoiler/Avant Garde-WORK/NST/Morimoto Halo/STi Clear Lenses/Carbon Signal Automotive/RJM Performance/ZSpeed Clutch Flywheel CSC delete

04-01-2016, 10:03 PM	#10 (permalink)
kenney255 Base Member Join Date: Mar 2016 Location: canada Posts: 14 Drives: 16 nissan 370z Rep Power: 9	when i looked online it said the duckbill was for the 09-12 , i have a 2016 do you know if there was any changes in the trunk from then ? thanks in advance

06-15-2016, 02:38 PM	#13 (permalink)
fury370 Base Member Join Date: Nov 2010 Location: Sumter Posts: 15 Drives: 40th Anniversary Rep Power: 14	Looks awesome! Question for you and sorry for thread jacking if it is. But since this has been pretty recent, how was your dealings with Aero jacket? I've ordered the same spoiler from them May 4th, and have yet to hear anything back from them, even after multiple emails sent to them. __________________ -2010 40th anniversary #134 -2006 4x4 Frontier CC -1994 5spd V6 mustang- 1/4 at 12.89 sprayed

06-15-2016, 03:30 PM	#15 (permalink)
BboyZ Enthusiast Member Join Date: Aug 2015 Location: Arizona Posts: 446 Drives: 2016 Z34 Nismo Rep Power: 9	Fitment really looks good to me. Congrats.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[WTB] Aerojacket/ Fly1 Duckbill type3	CM370z	Parts for sale (Private Classifieds)	0	03-25-2016 10:56 PM
evo r or aerojacket duckbill	fairlady_z34	Exterior & Interior	35	05-07-2015 05:18 PM
[FOR SALE] Aerojacket Duckbill in FRP (painted k51)	bwalla12	Parts for sale (Private Classifieds)	8	02-14-2015 01:19 PM
[FOR SALE] Aerojacket duckbill	ZLife	Parts for sale (Private Classifieds)	47	04-02-2014 04:52 PM
[FOR SALE] Aerojacket frp type 3 duckbill	threeseventy	Parts for sale (Private Classifieds)	11	07-06-2013 12:55 PM