Clutch pedal too soft/no feel? Remove the helper spring!

SE · 05-09-2011, 09:01 PM

You get a lot more feedback when taking out the spring, but one thing to note is that typically this shaft is also designed as an additional support for the clutch pedal. By removing the spring assembly entirely, it may cause a bit of side to side play when the pedal is depressed. Over time, this may cause premature wear on the CMC assembly and seals. The engineers who designed the clutch pedal designed for the mount to be used in conjunction with the spring assembly, not the top pivot mount by itself.

KingZee · 05-09-2011, 09:09 PM

Quote:

Originally Posted by VICTORxSE

You get a lot more feedback when taking out the spring, but one thing to note is that typically this shaft is also designed as an additional support for the clutch pedal. By removing the spring assembly entirely, it may cause a bit of side to side play when the pedal is depressed. Over time, this may cause premature wear on the CMC assembly and seals. The engineers who designed the clutch pedal designed for the mount to be used in conjunction with the spring assembly, not the top pivot mount by itself.

I knew this SHOULD be an issue over time, I think I'm in denial.

JB1 · 05-09-2011, 09:50 PM

Quote:

Originally Posted by VICTORxSE

You get a lot more feedback when taking out the spring, but one thing to note is that typically this shaft is also designed as an additional support for the clutch pedal. By removing the spring assembly entirely, it may cause a bit of side to side play when the pedal is depressed. Over time, this may cause premature wear on the CMC assembly and seals. The engineers who designed the clutch pedal designed for the mount to be used in conjunction with the spring assembly, not the top pivot mount by itself.

A solution for this can be to replace the spring for a much softer one. Then you will retain the additional support without the unwanted assistance of the stock spring. Someone on the G37 forum suggested the softer spring to take care of the little slack at the top, but I assume it'll work for this as well.

esfourteen · 05-09-2011, 11:00 PM

Quote:

Originally Posted by JB1

A solution for this can be to replace the spring for a much softer one. Then you will retain the additional support without the unwanted assistance of the stock spring. Someone on the G37 forum suggested the softer spring to take care of the little slack at the top, but I assume it'll work for this as well.

yeah that would in theory take care of both problems, now to find a spring

chops · 05-10-2011, 12:57 AM

Quote:

Originally Posted by JB1

A solution for this can be to replace the spring for a much softer one. Then you will retain the additional support without the unwanted assistance of the stock spring. Someone on the G37 forum suggested the softer spring to take care of the little slack at the top, but I assume it'll work for this as well.

the local hardware store/big hardware store sells tons of different kinds of springs!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
light clutch pedal?	boosted180	Engine & Drivetrain	21	06-07-2014 01:53 PM
clutch pedal issues?	xgrudgex	Engine & Drivetrain	17	01-31-2011 08:44 PM
How does your OEM clutch feel?	AlphaSnacks	Engine & Drivetrain	78	12-20-2010 11:04 AM
Knock from the clutch pedal	Oscar135	Engine & Drivetrain	34	07-27-2010 12:10 PM

05-09-2011, 09:01 PM	#1 (permalink)
SE A True Z Fanatic Join Date: Jan 2010 Location: San Jose, CA Posts: 4,236 Drives: 370z/STI/EVO X/IS-F Rep Power: 25	You get a lot more feedback when taking out the spring, but one thing to note is that typically this shaft is also designed as an additional support for the clutch pedal. By removing the spring assembly entirely, it may cause a bit of side to side play when the pedal is depressed. Over time, this may cause premature wear on the CMC assembly and seals. The engineers who designed the clutch pedal designed for the mount to be used in conjunction with the spring assembly, not the top pivot mount by itself.