DRL on with headlights MOD

Nixin · 11-20-2015, 03:04 PM

Cool. Will do this in April or May once the snow has melted, the salt is washed off the roads and the Z is outta storage.

BrockDM1 · 12-01-2015, 10:33 PM

Does anyone know if this works on the 2015 Nismo??

sixspeeddemon · 12-01-2015, 11:51 PM

Quote:

Originally Posted by BrockDM1

Does anyone know if this works on the 2015 Nismo??

Yes. It's the same car as a non nismo minus a few exterior mods and exhaust. It will work just fine.

Sent from my iPad using Tapatalk

Ghh0st · 12-09-2015, 11:16 PM

Quote:

Originally Posted by 14BlackCherry

Just thought I would add a quick addendum for anyone else doing this mod.

The electrical connector that worked for me was a 1/4" however I needed to file 1/16th off for it to fit snugly in the fuse box. I'll update if it loosens up. I think it will be okay though because it requires needle nose pliers to remove from the relay port.

Before:

After:

Night shot:

Thank you for this! I've been wanting to do this with my Z I just bought, but I didn't know the size of the spade connector.

BrockDM1 · 12-11-2015, 07:57 PM

Great write up. Did it on my 2015 Nismo

Ricks · 12-13-2015, 11:35 AM

Finally did this mod works awesome thank you!!!!

Apex2Apex · 12-15-2015, 06:57 PM

Finished this mod this evening. Hardest part was getting the connector to fit.

MagmaRed370z · 01-08-2016, 08:01 PM

Sorry for my big stupid ignorance. But how the heck do I do this? Read the whole 5 pages and I'm so confused.

So get to the box
Find the red and baige wires
Cut each in half? Then what?

Sorry need a step by step picture guide. Anybody want to help a wiring noob? I wish there would be a video or a step by step detailed guide.

Kabestro · 01-09-2016, 09:45 AM

Quote:

Originally Posted by schellingr

Sorry for my big stupid ignorance. But how the heck do I do this? Read the whole 5 pages and I'm so confused.

So get to the box
Find the red and baige wires
Cut each in half? Then what?

Sorry need a step by step picture guide. Anybody want to help a wiring noob? I wish there would be a video or a step by step detailed guide.

So, most people cut the wires, I didn't. I took my time and opened the connector and with a small (very small) flat head screwdriver took out the red and beige wires with their connectors. Tied the two together with some 18 gauge wire (I think) and the other end to a flat connector and stuck it in the plug. cover everything with electrical tape or plastic covers.

Powerwiz · 01-26-2016, 09:27 AM

Quote:

Originally Posted by schellingr

Sorry for my big stupid ignorance. But how the heck do I do this? Read the whole 5 pages and I'm so confused.

So get to the box
Find the red and baige wires
Cut each in half? Then what?

Sorry need a step by step picture guide. Anybody want to help a wiring noob? I wish there would be a video or a step by step detailed guide.

This is very simple to do...like 30 mins of your life perhaps a hour if you never have.

Essentially your cutting the two wires involved with DRL in IPDM box which is essentially a wiring junction box. Nissan for whatever reason created a complicated circuit that determines when your DRL are on or off. Kinda of puzzling since usually a engineer takes the easiest path for design.

You first step should be disconnecting the battery.

Find the two wires that provide power and ground to the DRL..the guides on this site point them out. When you cut them you will have 2 loose wires and the two stubs that are plugged in. For myself I just electrical taped wrapped the ends that are still plugged in.

You you need to remove some of the wire's insulation. You can do this with a tool designed for that or use like a razor blade. Twist the wires together then insert them into a spade connector.

Your DRL require 12 volts and there happens to be a 12 volt port with nothing in it. You take your spade connector and put into that slot. Thats it. Its simple.

Probably the hardest part is finding that spade connector that will stay in that slot. The one I had was slightly to wide so I trimmed it down some and inserted it.

Easy peasy.

40 to 332 · 01-26-2016, 04:17 PM

Well, here's a question for the automotive wiring geniuses. I like the idea of wiring the DRL so that they stay on when the headlights are on … and it seems like a pretty simple wiring job based on the above DIYs. However, is there a simple way to wire the DRL so that they stay on with the low beams, but turn off with the high beams (… much like front fog lights typically do)?

Powerwiz · 01-27-2016, 04:56 AM

Quote:

Originally Posted by 40 to 332

Well, here's a question for the automotive wiring geniuses. I like the idea of wiring the DRL so that they stay on when the headlights are on … and it seems like a pretty simple wiring job based on the above DIYs. However, is there a simple way to wire the DRL so that they stay on with the low beams, but turn off with the high beams (… much like front fog lights typically do)?

Not with that method. You would have to design the circuit to do that which would require some doing. The method described above bypasses Nissan's circuit and applies a continious 12volts to the LEDs while the car is on. The two are independent.

MagmaRed370z · 02-07-2016, 03:48 PM

Quote:

Originally Posted by Kabestro

So, most people cut the wires, I didn't. I took my time and opened the connector and with a small (very small) flat head screwdriver took out the red and beige wires with their connectors. Tied the two together with some 18 gauge wire (I think) and the other end to a flat connector and stuck it in the plug. cover everything with electrical tape or plastic covers.

Thank you for the pics! I so get it now

Quote:

Originally Posted by Powerwiz

This is very simple to do...like 30 mins of your life perhaps a hour if you never have.

Essentially your cutting the two wires involved with DRL in IPDM box which is essentially a wiring junction box. Nissan for whatever reason created a complicated circuit that determines when your DRL are on or off. Kinda of puzzling since usually a engineer takes the easiest path for design.

You first step should be disconnecting the battery.

Find the two wires that provide power and ground to the DRL..the guides on this site point them out. When you cut them you will have 2 loose wires and the two stubs that are plugged in. For myself I just electrical taped wrapped the ends that are still plugged in.

You you need to remove some of the wire's insulation. You can do this with a tool designed for that or use like a razor blade. Twist the wires together then insert them into a spade connector.

Your DRL require 12 volts and there happens to be a 12 volt port with nothing in it. You take your spade connector and put into that slot. Thats it. Its simple.

Probably the hardest part is finding that spade connector that will stay in that slot. The one I had was slightly to wide so I trimmed it down some and inserted it.

Easy peasy.

Thanks for the explanation. Will definitely do this later today!

MagmaRed370z · 02-19-2016, 05:33 PM

Today was the day. Finally completed it. Thanks for the instructions.

JohnTrang · 02-20-2016, 08:21 PM

Thanks 370zlvr, your route was the easiest way to do it!

Here are some additional pictures.

Update:
Check out my album for even more pictures:
http://www.the370z.com/members/johnt...s-drl-mod.html

12-11-2015, 07:57 PM	#65 (permalink)
BrockDM1 Enthusiast Member Join Date: Jun 2014 Location: Chicago Posts: 265 Drives: 15 Nismo Z Tech Rep Power: 10	Great write up. Did it on my 2015 Nismo Powerwiz, NismOrly22 and simul8r like this.

01-08-2016, 08:01 PM	#68 (permalink)
MagmaRed370z A True Z Fanatic Join Date: Jun 2014 Location: USA Posts: 1,468 Drives: 14' 370z Sport Magma Rep Power: 12	Sorry for my big stupid ignorance. But how the heck do I do this? Read the whole 5 pages and I'm so confused. So get to the box Find the red and baige wires Cut each in half? Then what? Sorry need a step by step picture guide. Anybody want to help a wiring noob? I wish there would be a video or a step by step detailed guide. Mike Tree likes this. __________________ Sold: 2014 Magnetic Black Base. Current: 2014 Magma Red 370z Sport \| ARK Grip Exhaust \| 25mm HR Spacers \| GTR Button \| DRL Mod

02-19-2016, 05:33 PM	#74 (permalink)
MagmaRed370z A True Z Fanatic Join Date: Jun 2014 Location: USA Posts: 1,468 Drives: 14' 370z Sport Magma Rep Power: 12	Today was the day. Finally completed it. Thanks for the instructions. NismOrly22 likes this. __________________ Sold: 2014 Magnetic Black Base. Current: 2014 Magma Red 370z Sport \| ARK Grip Exhaust \| 25mm HR Spacers \| GTR Button \| DRL Mod

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[WTB] Headlights	EastcoastZ	Parts for sale (Private Classifieds)	0	07-11-2013 09:09 AM
[WTB] Trade tinted headlights for clear headlights	ShoFamous	Parts for sale (Private Classifieds)	11	04-27-2012 01:54 PM
[WTB] Headlights	Dwv2005	Parts for sale (Private Classifieds)	0	03-05-2012 11:39 PM
Headlights	cfleming2226	Exterior & Interior	1	01-30-2012 06:40 PM
WTT: my PG painted headlights for your stock headlights	Cjanik	Parts for sale (Private Classifieds)	15	10-27-2010 02:28 PM

11-20-2015, 03:04 PM	#61 (permalink)
Nixin A True Z Fanatic Join Date: Sep 2015 Location: GWN Posts: 3,488 Drives: Goodbye Z! Rep Power: 19832	Cool. Will do this in April or May once the snow has melted, the salt is washed off the roads and the Z is outta storage.

12-01-2015, 10:33 PM	#62 (permalink)
BrockDM1 Enthusiast Member Join Date: Jun 2014 Location: Chicago Posts: 265 Drives: 15 Nismo Z Tech Rep Power: 10	Does anyone know if this works on the 2015 Nismo??

12-13-2015, 11:35 AM	#66 (permalink)
Ricks Base Member Join Date: Nov 2015 Location: Ny Posts: 5 Drives: 2015 370z Rep Power: 9	Finally did this mod works awesome thank you!!!!

12-15-2015, 06:57 PM	#67 (permalink)
Apex2Apex Base Member Join Date: Jul 2015 Location: Central Florida Posts: 130 Drives: 2015 370Z Rep Power: 9	Finished this mod this evening. Hardest part was getting the connector to fit.

01-26-2016, 04:17 PM	#71 (permalink)
40 to 332 Enthusiast Member Join Date: Apr 2013 Location: Kimberley, BC, CANADA Posts: 439 Drives: 13 370Z BS M6 Sport Rep Power: 138	Well, here's a question for the automotive wiring geniuses. I like the idea of wiring the DRL so that they stay on when the headlights are on … and it seems like a pretty simple wiring job based on the above DIYs. However, is there a simple way to wire the DRL so that they stay on with the low beams, but turn off with the high beams (… much like front fog lights typically do)?