DIY: Front license plate bracket Install

AK370Z · 05-10-2009, 10:55 AM

Quote:

Originally Posted by keioh

I'm just trying to install my front plates. The "J nut" is just too thick in the back and gets in the way for the License Plate Bracket to mount flush with the front bumper.
How did you secure your license plate screws to the Plate Bracket without the J nuts?
Went to the Dealer and the Service dept was closed and other people had no clue.
Any help would be appreciated.

thanks.

I did use the j-nuts. The license plate doesn't sit flush when you install them. But it doesn't look too bad. I also put a thin rubber slice so that the end of j-nuts do not rub my paint.

///M-Power · 05-10-2009, 11:36 AM

I'm not sure if you guys are allowed to puncture your plates in the US. But I simply bored holes on my plate where the plate holder screws are positioned and bought longer screws to mount the plate and holder. So plate and holder are held by the same pair of screws.

keioh · 05-10-2009, 11:03 PM

Quote:

Originally Posted by ///M-Power

I'm not sure if you guys are allowed to puncture your plates in the US. But I simply bored holes on my plate where the plate holder screws are positioned and bought longer screws to mount the plate and holder. So plate and holder are held by the same pair of screws.

thats a really good idea. I haven't aligned the plate with the holes but
I think the holes might get in the way of the letters or numbers.

keioh · 05-13-2009, 02:19 PM

Quote:

Originally Posted by keioh

thats a really good idea. I haven't aligned the plate with the holes but
I think the holes might get in the way of the letters or numbers.

I finally installed my front license plate the normal way as shown in the handbook. Except for 1 big change. I went to Ace Hardware and used
2 "J nut" that is made from hardened steel and is lot thinner than the enclosed plastic one. So everything is flush to the contour of the bumper
and no gaps.

AK370Z · 05-14-2009, 02:42 AM

Quote:

Originally Posted by keioh

I finally installed my front license plate the normal way as shown in the handbook. Except for 1 big change. I went to Ace Hardware and used
2 "J nut" that is made from hardened steel and is lot thinner than the enclosed plastic one. So everything is flush to the contour of the bumper
and no gaps.

Thanks. Will stop by my local ACE Hardware store on Saturday!

ConchZ2 · 05-14-2009, 07:55 AM

Here is another option...

STILLEN : STILLEN Front License Plate Bracket

theDreamer · 05-14-2009, 08:59 AM

Quote:

Originally Posted by ConchZ2

Here is another option...

STILLEN : STILLEN Front License Plate Bracket

I have this on order, hoping to have it this weekend and will post some pictures as soon as it is installed.

booboo1343 · 07-10-2010, 12:25 PM

I noticed that alot of people are saying that their j-nuts prevent them from mounting the LP bracket flush with the car. I fixed the problem by mounting the J-nuts on the bracket upside down. Screws will still work with the nut being upside down. My bracket is now flush with the car and the j-nut acts as a washer/nut, keeping the screw from digging into my bumper.

Astrosfan · 03-14-2011, 12:47 PM

I'd like to see some more pics of the stillen plate installed too! possible one from a distance? Ive done a search but came up with nothing.
thx

Somberlaine · 05-30-2011, 08:41 PM

hey guys, where would i buy the front license plate bracket? dealer? thnx

07-10-2010, 12:25 PM	#8 (permalink)
booboo1343 Base Member Join Date: May 2010 Location: San Antonio, Texas Posts: 7 Drives: 2010 Nissan 40th Ann Rep Power: 16	License Plate Mounting I noticed that alot of people are saying that their j-nuts prevent them from mounting the LP bracket flush with the car. I fixed the problem by mounting the J-nuts on the bracket upside down. Screws will still work with the nut being upside down. My bracket is now flush with the car and the j-nut acts as a washer/nut, keeping the screw from digging into my bumper.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
License Plate Bracket Damaging Our Cars?	TheWeatherman	Exterior & Interior	18	05-10-2013 08:22 PM
DIY: Power Retractable Front License Plate Install	ENT-Z	DIY Section (Do-It-Yourself)	36	09-27-2012 02:20 AM
Please put your front license plate on	AK370Z	North East Region	36	08-24-2009 02:30 PM
Installed front license plate bracket	AK370Z	Exterior & Interior	25	07-12-2009 12:01 PM
Front Plate Bracket	CantZme	Exterior & Interior	4	04-20-2009 08:52 PM

05-10-2009, 11:36 AM	#2 (permalink)
///M-Power Base Member Join Date: May 2009 Location: Philippines Posts: 9 Drives: 370Z Touring w/ SP Rep Power: 18	I'm not sure if you guys are allowed to puncture your plates in the US. But I simply bored holes on my plate where the plate holder screws are positioned and bought longer screws to mount the plate and holder. So plate and holder are held by the same pair of screws.

05-14-2009, 07:55 AM	#6 (permalink)
ConchZ2 Enthusiast Member Join Date: Feb 2009 Location: connecticut Posts: 329 Drives: 09 370Z red 6sp sprt Rep Power: 18	Here is another option... STILLEN : STILLEN Front License Plate Bracket

03-14-2011, 12:47 PM	#9 (permalink)
Astrosfan Enthusiast Member Join Date: Jan 2010 Location: houston, TX Posts: 427 Drives: 09 370z PG Sport Rep Power: 17	I'd like to see some more pics of the stillen plate installed too! possible one from a distance? Ive done a search but came up with nothing. thx

05-30-2011, 08:41 PM	#10 (permalink)
Somberlaine Base Member Join Date: Apr 2011 Location: Fairfax, VA Posts: 242 Drives: 2016 Golf R Rep Power: 16	hey guys, where would i buy the front license plate bracket? dealer? thnx