DIY: Adding In-Cabin air filter to the 370Z

g96818 · 02-02-2010, 02:17 AM

First off, i would like to thank you for pioneering this DIY, but I hope you don't mind if i expand a little more and make corrections on your DIY.
Do this at your own risk, I'm not responsible if you break something using this easier modified directions.

First off. there are 7 screws total. Screw #6 is sort of a hidden screw.

Remove screw 1 -> 4. if you have a super long screw driver then remove 5 -> 7 also, if not then read next step.

Next pull off the glove box. Grab the 2 spots circled in red and pull upwards. This allows you VERY easy access to screws 5 -> 7 as well as a much easier time removing the panel. This step is OPTIONAL, but as i mentioned, it gives you easy access to screws 5 -> 7 and it also gives you a spot to grab panel to pull it off. To put the glove box back, just line up the hinge and pop it back in.

Next GENTLY pull off the panel starting from the RIGHT side first. You don't wanna damage that extension area on the right side by pulling too hard on the left. Insert finger where the arrows are and grab the bottom with your other hand and pull. Do the same on the other side.
Removing the glove box lanyard is optional (actually, mines popped off as i was figuring how to put the glove box back in after accidentally removing it) but it gives you more space to work with.
Remember, pull GENTLY, you shouldn't have to pull hard after removing the hidden screw, #6.

The rest you can follow caneman88's to install/replace the filter. I just have one thing that I found might be useful and that is to cut 4 slots on the bottom of the filter wall so that you can close the vent door without smashing the filter. You'll know what i mean when you take off the vent door. Just line up the slots with the 4 things on the door and make like a 1/4" -> 1/2" cut. See pic for approx locations, measure the actual location with the vent door.

Yes the arrow on the filter points down. Air is sucked from the top and down into the circular thing.

I assume you guys know how to reverse the directions to put everything back.

Rep points much appreciated if you found this addition helpful

*edit* Fixed broken image. Let me know if the links are broken and I'll upload it again.

gurneyeagle · 03-08-2014, 10:53 AM

Quote:

Originally Posted by caneman88

Ok here is what to do if you want clean air inside your Z.
Bought the in cabin filter at Autozone for the Maxima seems like a lot of the Nissan's use the same filter.
1.About 6 screws to take glove box out then pull hard.
2.Open the vent door be careful the tab on the left on trap door breaks easy.
3.Insert filter and reassemble had to use a penny to hold left side tab broke.
4.Breathe the Clean Air.
5.Crank up the Red Hot Chili Peppers
Rep points needed:

Quote:

Originally Posted by g96818

First off, i would like to thank you for pioneering this DIY, but I hope you don't mind if i expand a little more and make corrections on your DIY.
Do this at your own risk, I'm not responsible if you break something using this easier modified directions.

First off. there are 7 screws total. Screw #6 is sort of a hidden screw.

Remove screw 1 -> 4. if you have a super long screw driver then remove 5 -> 7 also, if not then read next step.

Next pull off the glove box. Grab the 2 spots circled in red and pull upwards. This allows you VERY easy access to screws 5 -> 7 as well as a much easier time removing the panel. This step is OPTIONAL, but as i mentioned, it gives you easy access to screws 5 -> 7 and it also gives you a spot to grab panel to pull it off. To put the glove box back, just line up the hinge and pop it back in.

Next GENTLY pull off the panel starting from the RIGHT side first. You don't wanna damage that extension area on the right side by pulling too hard on the left. Insert finger where the arrows are and grab the bottom with your other hand and pull. Do the same on the other side.
Removing the glove box lanyard is optional (actually, mines popped off as i was figuring how to put the glove box back in after accidentally removing it) but it gives you more space to work with.
Remember, pull GENTLY, you shouldn't have to pull hard after removing the hidden screw, #6.

The rest you can follow caneman88's to install/replace the filter. I just have one thing that I found might be useful and that is to cut 4 slots on the bottom of the filter wall so that you can close the vent door without smashing the filter. You'll know what i mean when you take off the vent door. Just line up the slots with the 4 things on the door and make like a 1/4" -> 1/2" cut. See pic for approx locations, measure the actual location with the vent door.

Yes the arrow on the filter points down. Air is sucked from the top and down into the circular thing.

I assume you guys know how to reverse the directions to put everything back.

Rep points much appreciated if you found this addition helpful

*edit* Fixed broken image. Let me know if the links are broken and I'll upload it again.

A BIG THANK YOU to both you guys for this DIY!

I finally got around to doing this after having the filter for almost 18 months. Super-easy to do, especially if you pop out the glove box. It literally pops off the hinges, it's just a little scary doing it the first time. Don't worry, those parts are super-meaty.

I forgot to re-attach the lanyard and just pulled it back off without removing any of the screws. Honestly, I would suggest you pull off the glove box before loosening any screws.

Once all that is cleared-out, accessing the filter is easy. Just remember that the locking tab for the filter door is on the right side. It pops right off then you slide out the locating tab on the left.

g96818 · 04-28-2014, 11:37 PM

Quote:

Originally Posted by gurneyeagle

A BIG THANK YOU to both you guys for this DIY!

I finally got around to doing this after having the filter for almost 18 months. Super-easy to do, especially if you pop out the glove box. It literally pops off the hinges, it's just a little scary doing it the first time. Don't worry, those parts are super-meaty.

I forgot to re-attach the lanyard and just pulled it back off without removing any of the screws. Honestly, I would suggest you pull off the glove box before loosening any screws.

Once all that is cleared-out, accessing the filter is easy. Just remember that the locking tab for the filter door is on the right side. It pops right off then you slide out the locating tab on the left.

You know, I never put those screws back in since I first pulled it off. Much easier when i change the filter or mess with anything back there.

ramoszx12r · 05-27-2016, 07:20 AM

That is Very good Thanks.

Quote:

Originally Posted by g96818

First off, i would like to thank you for pioneering this DIY, but I hope you don't mind if i expand a little more and make corrections on your DIY.
Do this at your own risk, I'm not responsible if you break something using this easier modified directions.

First off. there are 7 screws total. Screw #6 is sort of a hidden screw.

Remove screw 1 -> 4. if you have a super long screw driver then remove 5 -> 7 also, if not then read next step.

Next pull off the glove box. Grab the 2 spots circled in red and pull upwards. This allows you VERY easy access to screws 5 -> 7 as well as a much easier time removing the panel. This step is OPTIONAL, but as i mentioned, it gives you easy access to screws 5 -> 7 and it also gives you a spot to grab panel to pull it off. To put the glove box back, just line up the hinge and pop it back in.

Next GENTLY pull off the panel starting from the RIGHT side first. You don't wanna damage that extension area on the right side by pulling too hard on the left. Insert finger where the arrows are and grab the bottom with your other hand and pull. Do the same on the other side.
Removing the glove box lanyard is optional (actually, mines popped off as i was figuring how to put the glove box back in after accidentally removing it) but it gives you more space to work with.
Remember, pull GENTLY, you shouldn't have to pull hard after removing the hidden screw, #6.

The rest you can follow caneman88's to install/replace the filter. I just have one thing that I found might be useful and that is to cut 4 slots on the bottom of the filter wall so that you can close the vent door without smashing the filter. You'll know what i mean when you take off the vent door. Just line up the slots with the 4 things on the door and make like a 1/4" -> 1/2" cut. See pic for approx locations, measure the actual location with the vent door.

Yes the arrow on the filter points down. Air is sucked from the top and down into the circular thing.

I assume you guys know how to reverse the directions to put everything back.

Rep points much appreciated if you found this addition helpful

*edit* Fixed broken image. Let me know if the links are broken and I'll upload it again.

Alienpoker · 01-17-2025, 05:49 PM

Quote:

Originally Posted by g96818

First off, i would like to thank you for pioneering this DIY, but I hope you don't mind if i expand a little more and make corrections on your DIY.
Do this at your own risk, I'm not responsible if you break something using this easier modified directions.

The rest you can follow caneman88's to install/replace the filter. I just have one thing that I found might be useful and that is to cut 4 slots on the bottom of the filter wall so that you can close the vent door without smashing the filter. You'll know what i mean when you take off the vent door. Just line up the slots with the 4 things on the door and make like a 1/4" -> 1/2" cut. See pic for approx locations, measure the actual location with the vent door.

Yes the arrow on the filter points down. Air is sucked from the top and down into the circular thing.

I assume you guys know how to reverse the directions to put everything back.

Rep points much appreciated if you found this addition helpful

*edit* Fixed broken image. Let me know if the links are broken and I'll upload it again.

Well… I know this is an ‘old thread’, but please don’t cut any slits / slots in your air filter. The white plastic ramps serve a purpose. They push the filter up against where it seals as you close the access flap.

02-02-2010, 02:17 AM	#1 (permalink)
g96818 Track Member Join Date: May 2009 Location: A rock in a big pond Posts: 681 Drives: 2009 370Z, 2012 M56 Rep Power: 3396	First off, i would like to thank you for pioneering this DIY, but I hope you don't mind if i expand a little more and make corrections on your DIY. Do this at your own risk, I'm not responsible if you break something using this easier modified directions. First off. there are 7 screws total. Screw #6 is sort of a hidden screw. Remove screw 1 -> 4. if you have a super long screw driver then remove 5 -> 7 also, if not then read next step. Next pull off the glove box. Grab the 2 spots circled in red and pull upwards. This allows you VERY easy access to screws 5 -> 7 as well as a much easier time removing the panel. This step is OPTIONAL, but as i mentioned, it gives you easy access to screws 5 -> 7 and it also gives you a spot to grab panel to pull it off. To put the glove box back, just line up the hinge and pop it back in. Next GENTLY pull off the panel starting from the RIGHT side first. You don't wanna damage that extension area on the right side by pulling too hard on the left. Insert finger where the arrows are and grab the bottom with your other hand and pull. Do the same on the other side. Removing the glove box lanyard is optional (actually, mines popped off as i was figuring how to put the glove box back in after accidentally removing it) but it gives you more space to work with. Remember, pull GENTLY, you shouldn't have to pull hard after removing the hidden screw, #6. The rest you can follow caneman88's to install/replace the filter. I just have one thing that I found might be useful and that is to cut 4 slots on the bottom of the filter wall so that you can close the vent door without smashing the filter. You'll know what i mean when you take off the vent door. Just line up the slots with the 4 things on the door and make like a 1/4" -> 1/2" cut. See pic for approx locations, measure the actual location with the vent door. Yes the arrow on the filter points down. Air is sucked from the top and down into the circular thing. I assume you guys know how to reverse the directions to put everything back. Rep points much appreciated if you found this addition helpful edit Fixed broken image. Let me know if the links are broken and I'll upload it again. kenchan, LinPark, eastwest2300 and 38 others like this. __________________ CZP are lying thieves! Last edited by g96818; 01-28-2016 at 04:10 PM. Reason: Fixed broken images again

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
No Cabin Filter on the 2009 370Z?	drisko	Nissan 370Z General Discussions	36	01-19-2023 02:26 AM
In Cabin Air Filter?	caneman88	Exterior & Interior	13	08-11-2012 10:50 AM
Cabin Filter	polarity	Nissan 370Z General Discussions	11	11-10-2009 11:24 PM
Confused Micro-Cabin Filter on 09's or just 2010?	Asheth	Nissan 370Z General Discussions	5	08-18-2009 10:00 PM
Cabin air filter	av370	Nissan 370Z General Discussions	3	07-17-2009 08:29 PM