IronX?

Spstone · 01-09-2016, 07:02 PM

Finally got around to detailing my Z after initial purchase 6 months ago. I went all in and got every thing Meguiars from Clay bar to interior cleaning wipes. Products actually worked out really well as I remember, except for one detail, I have a bunch of little rust spots across the whole car. Got on another thread and was told its iron deposits and I should get a product called IronX to correct it. I've got it ordered but haven't had a chance to use it yet. Has any one here used this product? Also any one have long term issues with this on PW cars?

Madcow · 01-09-2016, 10:40 PM

What you are seeing is iron fillings attached to the clear coat. You can remove these by clay barring, or alternatively use Iron-X which will dissolve them. Iron-X is relatively safe but take caution when spraying around break calipers. Also make sure you wear gloves and use it in a well ventilated area because it smells like a dead skunk.

old guy · 01-10-2016, 07:25 AM

madcow is right, clay bar will remove above the surface iron fillings, but iron x will dissolve below the surface of the clear coat. excellent surface prep for a long lasting finish!

Spstone · 01-10-2016, 08:01 AM

I did clay bar it, I was either not patient enough with it, or because the car sat on the lot for over a year than another 6 months in my drive way with out any real paint care it needs some thing a little stronger. I'll be giving the iron-x a try with the next wash. Thanks for the input guys.

SouthArk370Z · 01-10-2016, 09:14 AM

Claying should get rid of any surface contaminants. Either you are not claying properly (see Junkman2008's paint care threads on this site such as Junkman's "How to Completely Repair Your Paint Damage - The Videos!) or the filings are embedded in the paint.

RustX is a great product but it is rather harsh so follow the directions and, as others have mentioned, be careful what it gets on.

Madcow · 01-11-2016, 03:45 AM

Quote:

Originally Posted by Spstone

I did clay bar it, I was either not patient enough with it, or because the car sat on the lot for over a year than another 6 months in my drive way with out any real paint care it needs some thing a little stronger. I'll be giving the iron-x a try with the next wash. Thanks for the input guys.

Also keep in mind that clay comes in different grades/duties. A light duty clay bar will have a hard time picking up iron fillings, tar and tree sap. While a heavier duty will pick it up no problem.

cofo11 · 06-30-2016, 07:23 PM

Quote:

Originally Posted by Spstone

I did clay bar it, I was either not patient enough with it, or because the car sat on the lot for over a year than another 6 months in my drive way with out any real paint care it needs some thing a little stronger. I'll be giving the iron-x a try with the next wash. Thanks for the input guys.

Claying won't remove all of the iron deposits so if your car is in an area prone to contamination then Iron X should be part of your regimen.

Sent from my SAMSUNG-SM-N915A using Tapatalk

Junkman2008 · 07-04-2016, 10:45 PM

Quote:

Originally Posted by SouthArk370Z

Claying should get rid of any surface contaminants. Either you are not claying properly (see Junkman2008's paint care threads on this site such as Junkman's "How to Completely Repair Your Paint Damage - The Videos!) or the filings are embedded in the paint.

RustX is a great product but it is rather harsh so follow the directions and, as others have mentioned, be careful what it gets on.

Cydia · 07-15-2016, 06:38 PM

I just purchased a car from Cali, it has never had a "proper" wash, I'll show you the results of iron-x, it was pretty severe. I had to iron x twice and clay bar twice on the car for a perfectly clean surface ready to be buffed.

https://youtu.be/hDYHeK6_iC0
You should really watch the video in 1080p

Hope this link works! I just did it yesterday. Finished buffing too it took me another 14 hours.

MenZerna · 07-15-2016, 09:34 PM

Quote:

Originally Posted by Cydia

I just purchased a car from Cali, it has never had a "proper" wash, I'll show you the results of iron-x, it was pretty severe. I had to iron x twice and clay bar twice on the car for a perfectly clean surface ready to be buffed.

https://youtu.be/hDYHeK6_iC0
You should really watch the video in 1080p

Hope this link works! I just did it yesterday. Finished buffing too it took me another 14 hours.

White is really good to show off IronX working. Imagine it on a dark blue car or maybe a Plum Crazy Mopar, you would barely notice is working. But it still is!

Cydia · 07-16-2016, 11:03 AM

It's really impossible to see iron-x working on a black car, I've done it to a black Camaro and black hummer and you can only tell when it drops off and leaves the concrete purple ��

01-09-2016, 07:02 PM	#1 (permalink)
Spstone Enthusiast Member Join Date: Aug 2015 Location: Wilmington, nc Posts: 354 Drives: 14 370Z Nismo 6MT PW Rep Power: 10	IronX? Finally got around to detailing my Z after initial purchase 6 months ago. I went all in and got every thing Meguiars from Clay bar to interior cleaning wipes. Products actually worked out really well as I remember, except for one detail, I have a bunch of little rust spots across the whole car. Got on another thread and was told its iron deposits and I should get a product called IronX to correct it. I've got it ordered but haven't had a chance to use it yet. Has any one here used this product? Also any one have long term issues with this on PW cars?

01-09-2016, 10:40 PM	#2 (permalink)
Madcow Base Member Join Date: Nov 2015 Location: Nor Cal Posts: 30 Drives: 370z Nismo/CTS-V Rep Power: 10	What you are seeing is iron fillings attached to the clear coat. You can remove these by clay barring, or alternatively use Iron-X which will dissolve them. Iron-X is relatively safe but take caution when spraying around break calipers. Also make sure you wear gloves and use it in a well ventilated area because it smells like a dead skunk. __________________ 2015 370z Nismo --- 2013 Cadillac CTS-V Master Detailer

01-10-2016, 09:14 AM	#5 (permalink)
SouthArk370Z Premium Member Join Date: Nov 2010 Location: South Arkansas Posts: 8,435 Drives: 2014 Challenger Rep Power: 324198	Claying should get rid of any surface contaminants. Either you are not claying properly (see Junkman2008's paint care threads on this site such as Junkman's "How to Completely Repair Your Paint Damage - The Videos!) or the filings are embedded in the paint. RustX is a great product but it is rather harsh so follow the directions and, as others have mentioned, be careful what it gets on. __________________ Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
IronX and rust	ShutokuZ	Nissan 370Z General Discussions	7	08-31-2014 03:13 PM

01-10-2016, 07:25 AM	#3 (permalink)
old guy A True Z Fanatic Join Date: Apr 2015 Location: S.E. Michigan Age: 69 Posts: 2,711 Drives: 13 magma touring Rep Power: 2684370	madcow is right, clay bar will remove above the surface iron fillings, but iron x will dissolve below the surface of the clear coat. excellent surface prep for a long lasting finish!

01-10-2016, 08:01 AM	#4 (permalink)
Spstone Enthusiast Member Join Date: Aug 2015 Location: Wilmington, nc Posts: 354 Drives: 14 370Z Nismo 6MT PW Rep Power: 10	I did clay bar it, I was either not patient enough with it, or because the car sat on the lot for over a year than another 6 months in my drive way with out any real paint care it needs some thing a little stronger. I'll be giving the iron-x a try with the next wash. Thanks for the input guys.

07-15-2016, 06:38 PM	#9 (permalink)
Cydia Base Member Join Date: Jul 2016 Location: Gilbert Arizona Posts: 12 Drives: 13 370z Pearl White Rep Power: 10	I just purchased a car from Cali, it has never had a "proper" wash, I'll show you the results of iron-x, it was pretty severe. I had to iron x twice and clay bar twice on the car for a perfectly clean surface ready to be buffed. https://youtu.be/hDYHeK6_iC0 You should really watch the video in 1080p Hope this link works! I just did it yesterday. Finished buffing too it took me another 14 hours.

07-16-2016, 11:03 AM	#11 (permalink)
Cydia Base Member Join Date: Jul 2016 Location: Gilbert Arizona Posts: 12 Drives: 13 370z Pearl White Rep Power: 10	It's really impossible to see iron-x working on a black car, I've done it to a black Camaro and black hummer and you can only tell when it drops off and leaves the concrete purple ��