gtspec rear strut cross brace - help with bolt

speedfreek · 07-02-2014, 03:05 PM

I was in the market for the GT Spec bar. Maybe I should rethink this and try to source a Robispec harness bar instead.

Keep us updated on what you do about the bolt.

esfourteen · 07-02-2014, 04:06 PM

Quote:

Originally Posted by speedfreek

I was in the market for the GT Spec bar. Maybe I should rethink this and try to source a Robispec harness bar instead.

Keep us updated on what you do about the bolt.

i just got another reply after asking them to review the images I sent, they said they'll get back to me tomorrow. Worst case I'll go track down some M12x1.25 bolts of the desired length (need to measure).

inverted1 · 08-13-2014, 06:35 PM

I have a solution to the wrong bolt that gtspec supplies with their kit. I also contacted them about the problem and I am getting the same runaround you got. The original bolt is a M11x1.25mm. The bolt supplied is machined wrong. It is a M11 x about 1.15mm. It will start in the hole but will only go in about 2 turns until it tightens up. I am guessing it was made in China.

Get 2 each of the following:
7/16 x 20 TPI Grade 8 bolt 2.5 inches long.
7/16 flat washer with OD about .9 inch.
1/2 x 7/16 reducer 5/8 inch long.

I got the reducers on Ebay. Here is the link of what I bought.
1 2 to 7 16 Reducer Insert Spacer Heims Heim Joints | eBay

You can thread the bolt in by hand and it does not damage anything. I would also think it is stronger than the supplied bolt. I hope this helps anyone wanting to install this kit in their car. Other than the bolts, it is a nice kit.

07-02-2014, 03:05 PM	#1 (permalink)
speedfreek A True Z Fanatic Join Date: Feb 2012 Location: Huntsville,AL Posts: 1,724 Drives: '12 370Z PW 6sp Rep Power: 19	I was in the market for the GT Spec bar. Maybe I should rethink this and try to source a Robispec harness bar instead. Keep us updated on what you do about the bolt. __________________ Tomei\|Berk\|Takeda\|ZSpeed\|Fortune Auto\|Swift\|Eibach\|SPL\|Carbotech\|Motul\|Powertrix\|Stillen\|Aerojacket\|Z1\|Forgestar\|Enkei\|Project Kics\|Nismo Ti\|Llumar speedfreek's journal

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: GT Spec Rear Strut Cross Brace	TypeOne	DIY Section (Do-It-Yourself)	41	12-06-2015 10:38 PM
Gt spec rear strut cross brace	dainedazz	North East Region	2	12-25-2013 04:29 AM
Gt spec rear strut cross brace	dainedazz	Brakes & Suspension	12	12-19-2013 04:30 PM
Diy gt spec rear strut cross brace	dainedazz	DIY Section (Do-It-Yourself)	2	12-12-2013 12:56 PM
GTSPEC Rear Strut Brace and B Pillar Brace * Coming in / Pre Order *	RavSpec	Suspension/Brakes	18	08-27-2012 12:16 AM

08-13-2014, 06:35 PM	#3 (permalink)
inverted1 Base Member Join Date: Aug 2012 Location: Savannah GA Age: 53 Posts: 5 Drives: 2013 Sport Gray M6 Rep Power: 13	I have a solution to the wrong bolt that gtspec supplies with their kit. I also contacted them about the problem and I am getting the same runaround you got. The original bolt is a M11x1.25mm. The bolt supplied is machined wrong. It is a M11 x about 1.15mm. It will start in the hole but will only go in about 2 turns until it tightens up. I am guessing it was made in China. Get 2 each of the following: 7/16 x 20 TPI Grade 8 bolt 2.5 inches long. 7/16 flat washer with OD about .9 inch. 1/2 x 7/16 reducer 5/8 inch long. I got the reducers on Ebay. Here is the link of what I bought. 1 2 to 7 16 Reducer Insert Spacer Heims Heim Joints \| eBay You can thread the bolt in by hand and it does not damage anything. I would also think it is stronger than the supplied bolt. I hope this helps anyone wanting to install this kit in their car. Other than the bolts, it is a nice kit.