Nissan 370Z Forum  

Lowering Springs Comparisons

Originally Posted by /Angelo350Z/ I recently switched from Swift to Ark GT-S springs. I loved the Swift springs, they just didn't lower the car enough for me. The Ark GT-S

Go Back   Nissan 370Z Forum > Nissan 370Z Tech Area > Brakes & Suspension


Like Tree129Likes

Reply
 
LinkBack Thread Tools Display Modes
Old 06-22-2017, 09:26 PM   #136 (permalink)
Track Member
 
ChopsZ's Avatar
 
Join Date: May 2016
Location: Central Florida
Age: 48
Posts: 965
Drives: 2016 370Z GM 6MT
Rep Power: 2300
ChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond repute
Default

Quote:
Originally Posted by /Angelo350Z/ View Post

I recently switched from Swift to Ark GT-S springs. I loved the Swift springs, they just didn't lower the car enough for me. The Ark GT-S springs, on the other hand, just gives the Z a more menacing stance. With that said, my car's too low that I managed to destroy the front aero diffuser, left and right air guides, as well as bend both of my FI canisters in 48 hours. My car can literally scrape on a burrito. I'm switching to coilovers.
This doesn't make sense to me...

Swift = 1.2" F - 1.0" R
Ark GT-S = 1.4" F - 1.2" R

That's less than a 1/4" difference front and rear going from Swift to Ark. That's like the thickness of an iPhone. How can only dropping that much more all of a sudden cause you to scrape everywhere and damage mufflers?

When I had my '91 Miata, I had it lowered on coilovers, 1.75" front and 1.5" rear. That car sat a lot lower than a Z on Ark springs and I didn't bottom out and scrape on stuff with it at all. The only issue I had was a little scrubbing on full lock in the front.

Not arguing, just trying to understand that post.
NismOrly22 likes this.
__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity
ChopsZ is offline   Reply With Quote
Old 06-25-2017, 10:08 AM   #137 (permalink)
Track Member
 
ChopsZ's Avatar
 
Join Date: May 2016
Location: Central Florida
Age: 48
Posts: 965
Drives: 2016 370Z GM 6MT
Rep Power: 2300
ChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond repute
Default

Here's a good comparison between stock springs and Ark GT-S springs...



__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity
ChopsZ is offline   Reply With Quote
Old 07-09-2017, 04:09 PM   #138 (permalink)
Track Member
 
ChopsZ's Avatar
 
Join Date: May 2016
Location: Central Florida
Age: 48
Posts: 965
Drives: 2016 370Z GM 6MT
Rep Power: 2300
ChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond repute
Default

BTW, that pic above was after rolling right off the rack. I only drove it about 100 feet down the lot and 100 feet back, swerving a little bit both ways to try and "settle" down the ride height. I've been driving on these springs for two weeks now and they haven't settled anymore than what you see above.

Also, a couple quick questions which I have yet to see asked...

1) Has anyone had issues running into the bump stops with lowering springs?
2) Has anyone ever had issues with the drive shaft having less movement between the output shaft of the transmission and input shaft of the differential?
__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity
ChopsZ is offline   Reply With Quote
Old 07-10-2017, 11:48 AM   #139 (permalink)
Enthusiast Member
 
Join Date: Aug 2016
Location: SoCal
Age: 31
Posts: 383
Drives: Infiniti FX35
Rep Power: 35
MaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond repute
Default

Quote:
Originally Posted by ChopsZ View Post
This doesn't make sense to me...

Swift = 1.2" F - 1.0" R
Ark GT-S = 1.4" F - 1.2" R

That's less than a 1/4" difference front and rear going from Swift to Ark. That's like the thickness of an iPhone. How can only dropping that much more all of a sudden cause you to scrape everywhere and damage mufflers?

Not arguing, just trying to understand that post.
Although the static ride height difference may be negligible, the spring rate at those heights may have a difference in excess of 50-250ib/in.

A softer spring will allow more ride undulation. Given the fact they are both dual rate progressive springs, the length and transitional rates could be massively different.

*** After further research, the swift spring actually is the stiffer overall spring. The coil diameter is larger and has a higher rate for the tighter wind coils "dead coils". The transitional rate between soft and stiffer would probably be smaller overall. So even though the ARK srpings sits a marginal amount higher, the spring travel is greater. Which ark springs is said person talking about though? Gt-s or Gt-f?

Last edited by MaysEffect; 07-10-2017 at 02:03 PM.
MaysEffect is offline   Reply With Quote
Old 07-11-2017, 08:41 PM   #140 (permalink)
Track Member
 
ChopsZ's Avatar
 
Join Date: May 2016
Location: Central Florida
Age: 48
Posts: 965
Drives: 2016 370Z GM 6MT
Rep Power: 2300
ChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond repute
Default

Quote:
Originally Posted by ChopsZ View Post
Also, a couple quick questions which I have yet to see asked...

1) Has anyone had issues running into the bump stops with lowering springs?
2) Has anyone ever had issues with the drive shaft having less movement between the output shaft of the transmission and input shaft of the differential?
So does anyone have anything for these questions? Just curious.
__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity
ChopsZ is offline   Reply With Quote
Old 07-16-2017, 07:11 PM   #141 (permalink)
Track Member
 
ChopsZ's Avatar
 
Join Date: May 2016
Location: Central Florida
Age: 48
Posts: 965
Drives: 2016 370Z GM 6MT
Rep Power: 2300
ChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond repute
Default

So with ALL of the members on here over ALL of the years of lowering these cars one way or another, no one has any answers for these two questions? Really?...
__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity
ChopsZ is offline   Reply With Quote
Old 07-16-2017, 08:28 PM   #142 (permalink)
Ronin Samurai - Assassin
 
Rusty's Avatar
 
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 68
Posts: 34,812
Drives: 2011 Nismo GM 6M
Rep Power: 2684436
Rusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond repute
Talking

Quote:
Originally Posted by ChopsZ View Post
BTW, that pic above was after rolling right off the rack. I only drove it about 100 feet down the lot and 100 feet back, swerving a little bit both ways to try and "settle" down the ride height. I've been driving on these springs for two weeks now and they haven't settled anymore than what you see above.

Also, a couple quick questions which I have yet to see asked...

1) Has anyone had issues running into the bump stops with lowering springs?
2) Has anyone ever had issues with the drive shaft having less movement between the output shaft of the transmission and input shaft of the differential?
Quote:
Originally Posted by ChopsZ View Post
So does anyone have anything for these questions? Just curious.
Quote:
Originally Posted by ChopsZ View Post
So with ALL of the members on here over ALL of the years of lowering these cars one way or another, no one has any answers for these two questions? Really?...
Question 1. Depending on how low you go. Will determine when you will hit the bump stops and how often. Everyone has hit the bump stops at one time or another. You just don't know it.

Question 2. Lowering the car has nothing the do with the driveshaft between the tranny and diff. Both are fixed in position. The driveshaft doesn't move. It's fixed at the diff. You should be concern about the halfshafts between the diff and knuckle. The diff stays in place the the knuckle moves up and down in an arc.
ChopsZ likes this.
__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html
Rusty is offline   Reply With Quote
Old 07-17-2017, 12:29 AM   #143 (permalink)
Track Member
 
ChopsZ's Avatar
 
Join Date: May 2016
Location: Central Florida
Age: 48
Posts: 965
Drives: 2016 370Z GM 6MT
Rep Power: 2300
ChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond reputeChopsZ has a reputation beyond repute
Default

Quote:
Originally Posted by Rusty View Post
Question 1. Depending on how low you go. Will determine when you will hit the bump stops and how often. Everyone has hit the bump stops at one time or another. You just don't know it.

Question 2. Lowering the car has nothing the do with the driveshaft between the tranny and diff. Both are fixed in position. The driveshaft doesn't move. It's fixed at the diff. You should be concern about the halfshafts between the diff and knuckle. The diff stays in place the the knuckle moves up and down in an arc.

Q1) I ask about the bump stops because I wanted to know just how close we actually are to them once lowered. On one of the roads I normally drive on almost daily, there's two manhole covers in the middle of the lane, and for whatever reason, the road has a couple of really sharp dips (ripples) between them. While stock, it's quite an abrupt bounce through there. Now that I'm lowered, it's an actual "jolt" going through there. I'm assuming that jolt is from ramming right into the rear bump stops. It does not seem to bother the front at all.

I'm sure we do all ride the bump stops once in a while without knowing it. If our Z's are setup like Miatas, they are designed to compress the springs fully and then gradually compress the bump stops as the bump stops on Miatas are actually factored into the handling of the car. They rely on riding on the bump stops during hard cornering.


Q2) I don't know why, but for some reason, I have been thinking about it as if it were a live axle, which it's not. I wasn't even thinking about the fact that the diff is physically connected to the chassis. Sorry about that.

On that note, what concerns would there be with the half shafts? Only asking for curiosity reasons. I have no plans on ever going any lower than what the Ark GT-S springs give me.

As it is, I sometimes think I should have stuck to my guns and went with the Swifts. Not because of rubbing or bottoming out, but because the front and rear tires tuck a little now which prevents me from using spacers, and also limits me on eventually going with wider meat front and rear.
__________________
She's For Sale! PERFORMANCE: Aero Workz | Akebono | BC Racing | EcuTek | HKS | MaxBore | Motordyne | Nismo | RJM | SPL | StopTech | Z1
AUDIO: Arc Audio | Bazooka | Helix | Pioneer | Stereo Integrity
ChopsZ is offline   Reply With Quote
Old 07-17-2017, 01:33 AM   #144 (permalink)
Ronin Samurai - Assassin
 
Rusty's Avatar
 
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 68
Posts: 34,812
Drives: 2011 Nismo GM 6M
Rep Power: 2684436
Rusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond repute
Talking

To get into the halfshafts is long and detailed. It deals with angles of operation, engineering POV. Had to deal with it at work. And I don't feel like getting into right now. But with the Z. You don't have to worry about them. Unless you are pushing mega HP and torque. From a strength POV.
ChopsZ likes this.
__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html
Rusty is offline   Reply With Quote
Old 07-17-2017, 04:31 AM   #145 (permalink)
Enthusiast Member
 
Join Date: Aug 2016
Location: SoCal
Age: 31
Posts: 383
Drives: Infiniti FX35
Rep Power: 35
MaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond repute
Default

Quote:
Originally Posted by ChopsZ View Post
Q1)

I'm sure we do all ride the bump stops once in a while without knowing it. If our Z's are setup like Miatas, they are designed to compress the springs fully and then gradually compress the bump stops as the bump stops on Miatas are actually factored into the handling of the car. They rely on riding on the bump stops during hard cornering. - NOOOOO, this practice was used on much lighter and older NA and NB's and to be honest should be done at all. Older rubber bumps stops were rather long and soft with a soft bump curve. Newer designed bump stops/plates are purely for keeping the car from bottoming out on the tire or suspension parts binding or bashing the shocks out.
Constantly riding on the bumpstops is NOT a good thing. Slamming the bumps can cause damage and premature failure to the damper. Also considering the low profiles tires, this will be exerting more load on the tire sidewall and ultimately the wheel rim. The miata for example had larger sidewalls, softer tires overall and softer bumpstops with more absorption.

There are however aftermarket bumpstops with tuned bump curves that will allow some further compression instead of hard stops in compression stroke.

I'm inclined to believe the jolt you are feeling is from the rear springs binding the "dead springs" Where as the fronts are already fully bound at normal ride height due to the weight bias. Next time you have car up in the air, check if you see scratches/indentations between the tightly bound coils


With regards to the halfshafts, the suspension geometry as factory is designed to keep the shafts relatively level during normal driving conditions. Increased camber, lower ride height. higher torque loads and blown out bushings can cause premature failure to the boots, the internal cages/races and the shaft itself. Ripped boots is a slower wear issue which usually leads to damaged bearings which is a noticeable failure. Damage to the cages and races would almost definitely be catastrophic failure. A snapped shaft is probably the most preferred failure, in a worse case it will bend and start playing hammer fist with the surrounding suspension pieces. This will probably fail at lowspeed.

There are plenty of details on how it all can fail like Rusty suggested.
Rusty likes this.

Last edited by MaysEffect; 07-17-2017 at 02:26 PM.
MaysEffect is offline   Reply With Quote
Old 07-17-2017, 04:05 PM   #146 (permalink)
Enthusiast Member
 
Join Date: Aug 2016
Location: SoCal
Age: 31
Posts: 383
Drives: Infiniti FX35
Rep Power: 35
MaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond reputeMaysEffect has a reputation beyond repute
Default

Quote:
Originally Posted by MaysEffect View Post
There are however aftermarket bumpstops with tuned bump curves that will allow some further compression instead of hard stops in compression stroke.
I should clarify on this, by saying tuning bump rates should be done professionally. Using original sized bumpstops as a way to tune bump compression is not ideal, certainly with progressive rate springs.
MaysEffect is offline   Reply With Quote
Old 11-29-2017, 06:51 AM   #147 (permalink)
A True Z Fanatic
 
onzedge's Avatar
 
Join Date: Apr 2010
Location: Battle Lake MN
Age: 63
Posts: 183,964
Drives: 370Z 240Z
Rep Power: 2684735
onzedge has a reputation beyond reputeonzedge has a reputation beyond reputeonzedge has a reputation beyond reputeonzedge has a reputation beyond reputeonzedge has a reputation beyond reputeonzedge has a reputation beyond reputeonzedge has a reputation beyond reputeonzedge has a reputation beyond reputeonzedge has a reputation beyond reputeonzedge has a reputation beyond reputeonzedge has a reputation beyond repute
Default

Bump
__________________
Koni|Swift|Michelin|Motordyne|Berk|RJM Performance|Gates|SPL|Motul|Technafit|Ate Super Blue|Hawk
Tommy Kaira|Momo|Optima|Hella|Hotchkis|Red Line|ZSpeed|Stillen|B&M|H&R
onzedge is offline   Reply With Quote
Old 11-29-2017, 09:14 AM   #148 (permalink)
Ronin Samurai - Assassin
 
Rusty's Avatar
 
Join Date: Dec 2011
Location: Fayettenam,Pennsyltucky
Age: 68
Posts: 34,812
Drives: 2011 Nismo GM 6M
Rep Power: 2684436
Rusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond reputeRusty has a reputation beyond repute
Talking

Quote:
Originally Posted by onzedge View Post
Bump
Attached Images
File Type: jpg Grave Digger.jpg (106.6 KB, 49 views)
__________________

浪人 - 殺し屋
"The Difficult Anytime, The Impossible By Appointment Only"
http://www.the370z.com/members-370z-...o-journal.html
Rusty is offline   Reply With Quote
Old 12-21-2017, 11:17 PM   #149 (permalink)
Base Member
 
Join Date: Oct 2017
Location: California
Posts: 1
Drives: 06 Nissan 370 Sports
Rep Power: 7
ZED34Dude is on a distinguished road
Default

Wow! Thanks, this is amazing! Anyone running Ti2000 RS-R Lowering Springs? I never heard of them.
ZED34Dude is offline   Reply With Quote
Old 03-11-2018, 09:58 PM   #150 (permalink)
Base Member
 
Join Date: Jan 2017
Location: Florida
Posts: 52
Drives: 2016 370Z Nismo
Rep Power: 8
NismOrly22 is on a distinguished road
Default

What's up Z nation? Quick feedback guys.
Want to go w/ a "conservative" drop on my Z. Thinking of going w/ the ARK GT-F lowering springs along w/ rear camber arms and toe bolts.
With this "conservative" setup will I need spacers? And if so, what size spacers would you guys recommend?
Any other information or advice on this setup would be greatly appreciated.
#Znation
NismOrly22 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Lowering springs Z370Z011 Brakes & Suspension 37 02-18-2014 10:23 AM
ARK lowering springs Bigd4mcc Suspension/Brakes 0 02-13-2013 04:15 AM
wtb lowering springs BRI888 Northern California Region 2 06-11-2011 02:18 AM
WTB: H&R Lowering Springs KcL@AOI Wanted 6 07-27-2010 10:35 PM
H&R Lowering Springs? CBRich Brakes & Suspension 8 03-01-2010 12:35 PM


All times are GMT -5. The time now is 03:49 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2