f.i. l.t.h. for right hand driver?

370z_2910 · 05-16-2010, 08:14 PM

any idea if f.i. is going to produce for our right hand driver?

i've already contact them and waiting for their reply....

just wondering, if other members have contacted them...

also, if they do produce it, that's mean lth + cbe is the complete package for the exhaust system...

meaning that we don't have to purchase the header, cats and test pipe from what i've read from intake / exhaust thread?...

m4a1mustang · 05-16-2010, 08:15 PM

Quote:

Originally Posted by 370z_2910

any idea if f.i. is going to produce for our right hand driver?

i've already contact them and waiting for their reply....

just wondering, if other members have contacted them...

also, if they do produce it, that's mean lth + cbe is the complete package for the exhaust system...

meaning that we don't have to purchase the header, cats and test pipe from what i've read from intake / exhaust thread?...

I don't know what their plans are with regards to production, but if they do make LTHs available for the right hand drive cars, then yes, LTH + CBE is the complete package.

MYZ34 · 05-18-2010, 08:18 AM

hi "370z_2910" i have already spoken to tony at F.I and he has said that the LTH's for left hand drive 370z will not fit ours, also he cannot make them to suit our cars as he does not have access to a right hand 370z, he did say however if someone would be able to take under car pictures, specially where the right hand drive steering shaft goes down and other pics around the left and right sides, he may be able to do something. i would love to take my car to a hoist to take pics, but don't have the time. if any of you guys could manage that keep us posted as i'm sure there are a lot us over here in Aus wanting these....MYZ34

EVL370 · 05-18-2010, 08:44 AM

I would of guessed it would of been ok.

A couple of blokes in Aus have stillen heads straight off the boat from the states. They fitted.

theDreamer · 05-18-2010, 08:47 AM

Quote:

Originally Posted by EVL370

I would of guessed it would of been ok.

A couple of blokes in Aus have stillen heads straight off the boat from the states. They fitted.

Those are short headers, F.I. are long tube headers so the difference is around the cats mainly.

BGTV8 · 05-18-2010, 06:14 PM

I have Stillen Stainless headers on my car, and at about 15 degrees of left hand lock, the nut on the steering column joint at the rack "just" touches and I get the faintest vibration which was a little off-putting until I figured out what it was ... I will eventually replace the bolt with a grade 8 half-height boolt head or perhaps a cap-screw to avoid it ....

BGTV8 · 05-18-2010, 06:17 PM

I have Stillen headers fitted to my car and at about 15 degress of left-hand lock, I get a vibration as the bolt-head that holds the steering column universal joint onto the rack just touches the outer circumference of the RG header .. was a little off-putting until I figured out what it was. Will replace this bolt with a half-height head Grade 8 bolt, or perhaps a cap-screw in due course to avoid it ... there is not a lot of room with these headers at the point where the steering column uni-joint fits onto the rack ...

370z_2910 · 05-19-2010, 07:51 AM

maybe after the next service, i'll try to take few pictures...under neat the engine bay, right?

how about the taking pictures under the hood?

MYZ34 · 05-20-2010, 07:38 AM

yeah as many pics as possible, as tony needs to use them to see whether or not they can be made

370z_2910 · 06-04-2010, 11:30 PM

i've email f.i. and tony said that he have difficulty in producing the headers unless there is an actual right hand drive car at his garage...

so sending the pics to him is useless....

i'm still waiting on xforce exhaust to produce a decent header (maybe) but they said that they have no plan on doing one....

from their website i could see that they have produced 350z header and complete exhaust system...

05-16-2010, 08:14 PM	#1 (permalink)
370z_2910 Base Member Join Date: Sep 2009 Location: BRUNEI Posts: 127 Drives: 370Z Rep Power: 15	f.i. l.t.h. for right hand driver? any idea if f.i. is going to produce for our right hand driver? i've already contact them and waiting for their reply.... just wondering, if other members have contacted them... also, if they do produce it, that's mean lth + cbe is the complete package for the exhaust system... meaning that we don't have to purchase the header, cats and test pipe from what i've read from intake / exhaust thread?...

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Whats going rate for second hand 370z headlights?	370Zvetlana	Exterior & Interior	3	03-22-2010 09:10 PM
Looking for a hand to fang delete and valance black out - ATX - surrounding	Kastley85891	Texas	9	03-07-2010 12:27 PM
My Hand Auto Wash & Detailing Spot in NJ	zcoupe09	North East Region	1	06-14-2009 09:40 PM
My new hand wash and detailing center...	zcoupe09	Nissan 370Z General Discussions	0	05-12-2009 01:09 PM

05-18-2010, 08:18 AM	#3 (permalink)
MYZ34 Base Member Join Date: Sep 2009 Location: brisbane AUS Posts: 111 Drives: 2009 370z 6spd Rep Power: 15	hi "370z_2910" i have already spoken to tony at F.I and he has said that the LTH's for left hand drive 370z will not fit ours, also he cannot make them to suit our cars as he does not have access to a right hand 370z, he did say however if someone would be able to take under car pictures, specially where the right hand drive steering shaft goes down and other pics around the left and right sides, he may be able to do something. i would love to take my car to a hoist to take pics, but don't have the time. if any of you guys could manage that keep us posted as i'm sure there are a lot us over here in Aus wanting these....MYZ34

05-18-2010, 08:44 AM	#4 (permalink)
EVL370 Base Member Join Date: Dec 2009 Location: Melbourne Posts: 209 Drives: Nissan 370Z Rep Power: 15	I would of guessed it would of been ok. A couple of blokes in Aus have stillen heads straight off the boat from the states. They fitted.

05-18-2010, 06:14 PM	#6 (permalink)
BGTV8 A True Z Fanatic Join Date: Dec 2009 Location: 03350 Australia Posts: 1,503 Drives: 09 Nissan 370Z M6 Rep Power: 29907	I have Stillen Stainless headers on my car, and at about 15 degrees of left hand lock, the nut on the steering column joint at the rack "just" touches and I get the faintest vibration which was a little off-putting until I figured out what it was ... I will eventually replace the bolt with a grade 8 half-height boolt head or perhaps a cap-screw to avoid it ....

05-18-2010, 06:17 PM	#7 (permalink)
BGTV8 A True Z Fanatic Join Date: Dec 2009 Location: 03350 Australia Posts: 1,503 Drives: 09 Nissan 370Z M6 Rep Power: 29907	I have Stillen headers fitted to my car and at about 15 degress of left-hand lock, I get a vibration as the bolt-head that holds the steering column universal joint onto the rack just touches the outer circumference of the RG header .. was a little off-putting until I figured out what it was. Will replace this bolt with a half-height head Grade 8 bolt, or perhaps a cap-screw in due course to avoid it ... there is not a lot of room with these headers at the point where the steering column uni-joint fits onto the rack ...

05-19-2010, 07:51 AM	#8 (permalink)
370z_2910 Base Member Join Date: Sep 2009 Location: BRUNEI Posts: 127 Drives: 370Z Rep Power: 15	maybe after the next service, i'll try to take few pictures...under neat the engine bay, right? how about the taking pictures under the hood?

05-20-2010, 07:38 AM	#9 (permalink)
MYZ34 Base Member Join Date: Sep 2009 Location: brisbane AUS Posts: 111 Drives: 2009 370z 6spd Rep Power: 15	yeah as many pics as possible, as tony needs to use them to see whether or not they can be made

06-04-2010, 11:30 PM	#10 (permalink)
370z_2910 Base Member Join Date: Sep 2009 Location: BRUNEI Posts: 127 Drives: 370Z Rep Power: 15	i've email f.i. and tony said that he have difficulty in producing the headers unless there is an actual right hand drive car at his garage... so sending the pics to him is useless.... i'm still waiting on xforce exhaust to produce a decent header (maybe) but they said that they have no plan on doing one.... from their website i could see that they have produced 350z header and complete exhaust system...