Quick wiring question w/ pic

scionide · 01-05-2012, 06:47 PM

The white/blue wire on the left is from my kenwood HU, the blue/white wire on the right is from the metra harness.

The left wire was labeled, P Cont. and the right one according to the labeling chart is the amp turn on.

My question is does it matter which wire I connect my remote turn on wire from my amp to? Since I think they both do the same thing.

DCNISMO · 01-05-2012, 06:56 PM

I think P cont means power is on even if the car is off..

from the HU I'm gusssing its switched, only on if car is on or in accessory position.

I don't think you want power to your amp all the time.

Put a voltmeter on them to see what you have. Or call Crutchfield....they are good tech help.

bigaudiofanat · 01-05-2012, 07:07 PM

Quote:

Originally Posted by DCNISMO

I think P cont means power is on even if the car is off..

from the HU I'm gusssing its switched, only on if car is on or in accessory position.

I don't think you want power to your amp all the time.

Put a voltmeter on them to see what you have. Or call Crutchfield....they are good tech help.

Incorrect, P Cont means the the power will be on continuously when the head unit is on.

You can wire the antenna adapter to this wire if you want. It will not harm anything just will have the antenna on even if your playing a CD.

Some head units only have that wire and no powered antenna wire. If you have a powered antenna wire I would use that. However note that sometimes the powered antenna wire does not supply enough voltage.

scionide · 01-05-2012, 07:34 PM

Quote:

Originally Posted by bigaudiofanat

Incorrect, P Cont means the the power will be on continuously when the head unit is on.

You can wire the antenna adapter to this wire if you want. It will not harm anything just will have the antenna on even if your playing a CD.

Some head units only have that wire and no powered antenna wire. If you have a powered antenna wire I would use that. However note that sometimes the powered antenna wire does not supply enough voltage.

My antenna is connected to a wire labeled Antenna CONT. on my HU (I'm assuming this is the powered antenna wire you're referring to?)

So since the P Cont is always on with the head unit, it'd be fine to connect my remote turn on wire from my amp to it right?

DCNISMO · 01-05-2012, 08:12 PM

I was half right..... A side question, you said that tap might not provide enough voltage, so it might be less than 12 volts?....or did you mean current? A power audio amp would draw a lot more current than a low gain op amp circuit in the antenna.

bigaudiofanat · 01-05-2012, 08:40 PM

Quote:

Originally Posted by DCNISMO

I was half right..... A side question, you said that tap might not provide enough voltage, so it might be less than 12 volts?....or did you mean current? A power audio amp would draw a lot more current than a low gain op amp circuit in the antenna.

The current is what I mean. However it is rare that this happens.

01-05-2012, 06:47 PM	#1 (permalink)
scionide Enthusiast Member Join Date: Mar 2011 Location: so-cal Posts: 436 Drives: 11 370z PW 6mt Rep Power: 14	Quick wiring question w/ pic The white/blue wire on the left is from my kenwood HU, the blue/white wire on the right is from the metra harness. The left wire was labeled, P Cont. and the right one according to the labeling chart is the amp turn on. My question is does it matter which wire I connect my remote turn on wire from my amp to? Since I think they both do the same thing.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wiring question for someone who's taken the interior apart	delorean	Audio & Video	11	10-10-2011 07:15 PM
Audio Wiring Question	jpit	Audio & Video	11	03-28-2010 06:25 PM
Nissan wiring harness question.	Z33knight	Audio & Video	5	03-26-2010 01:33 PM
Car wiring harness question	Mike	Audio & Video	4	09-30-2009 04:57 AM
Upgrading stock Subs - wiring question	evse82	Audio & Video	6	07-28-2009 05:22 PM

01-05-2012, 06:56 PM	#2 (permalink)
DCNISMO Track Member Join Date: Nov 2011 Location: washington dc Posts: 995 Drives: Nismo Z Rep Power: 178	I think P cont means power is on even if the car is off.. from the HU I'm gusssing its switched, only on if car is on or in accessory position. I don't think you want power to your amp all the time. Put a voltmeter on them to see what you have. Or call Crutchfield....they are good tech help.

01-05-2012, 08:12 PM	#5 (permalink)
DCNISMO Track Member Join Date: Nov 2011 Location: washington dc Posts: 995 Drives: Nismo Z Rep Power: 178	I was half right..... A side question, you said that tap might not provide enough voltage, so it might be less than 12 volts?....or did you mean current? A power audio amp would draw a lot more current than a low gain op amp circuit in the antenna.