Engine Noise through Speakers

Carbon_z · 12-09-2010, 07:13 PM

Well I did a bunch of searches and assuming i have to ground my RCA's but want to verify. The first Head unit I had was a Sony xav70bt. It didnt produced any engine noise. The ground wire, amp, speakers etc are all still in the same place. The new replacement headunit is a Pioneer Avic-x920bt. Only difference setup wise is that a bypass was done on the harness of the new unit for dvd and nav usage. Once the unit is turned on, the pioneer produces alot of engine noise through the speakers. The second the unit is powered up the noise is NON STOP. If I turn the car ON but without cranking it, the noise only appears when the car is in gear but if in neutral the engine sound does not come through the speakers "WEIRD". . When car is cranked on or turned over, engine sound comes through speakers whether in gear or neutral, unlike the on position did in my previous sentence. I ran the power wire down the passenger side, amp is located behind the passenger seat. Ground wire is bolted on one of the passengar seats bolts. I have a 3 channel amp and have tried replacing the RCA's with another pair and the same sound occurs. I figured replacing the RCA would fix it but i tested the NEW RCA's without tucking them in, just loose away from everything but the sound was still there

Any help would be great.

Carbon_z · 12-09-2010, 07:23 PM

also just realized I cant wrap wire around the rca's since the units rca are part of a harness. Guess the wire wrap is for older units. **** is annoying as hell

FERRARI · 12-09-2010, 08:08 PM

Have you used a ohmmeter to check the continuity of your wiring and your ground?

90 ST · 12-09-2010, 09:42 PM

Double check your ground, also check to see what the resistance is between the ground set screw on the amp and the battery post, if it's too high it could just be a bad ground. Also try hooking up the deck without the bypass just to make sure it's not the by pass ground causing it. If you didn't have to ground your RCA's before you shouldn't have to now.

Carbon_z · 12-09-2010, 09:50 PM

Haven't checked with meter yet... The bypass was moving a mute wire to a pin to the left so I can't check it since the bypass was only that. All the grounds on the back of the headunit are connected together since it's just ground. I might run it by the audio shop tomorrow but it's pissing me off ..

6spdcoupe · 12-10-2010, 01:38 AM

Most likely your culprit ..

pioneer pico fuse avic - Google Search

This is a primary reason why we do not support or sell Pioneer.

Carbon_z · 12-10-2010, 11:47 AM

also in addition, tried the LOOP for the rca's and some of the noise went away but still existed. If it was the headunit, wouldnt the loop have caught the noise??? I tried it behind the unit and on the amp. Same result. Could the speaker wires be causing this or the ground???? the speaker wires are 16 gauge and i have sr 60 Boston acoustics.

90 ST · 12-10-2010, 12:01 PM

unlikely the speaker wires, but yes the ground to the amp could, as i mentioned earlier.

Carbon_z · 12-10-2010, 12:21 PM

my ground is currently under one of the passenger seats bolts that bolt to the frame of the car. Figured that was a good enough good but didnt script metal. Also the ground on the headunit is on one of the 4 bolts to the shift plate on the frame

90 ST · 12-10-2010, 12:24 PM

sand the paint of the amp ground and make sure you have set the gains accordingly

6spdcoupe · 12-10-2010, 12:38 PM

I absolutely agree with the sanding down the ground plane, however I believe with 99% certainty that this is not your problem. Had this been a fresh install and nothing prior was in the car, then sure, it could be one of many possibilities. However you mentioned you had a Sony deck prior and no issues.

You now have a control (your vehicle and equipment inside) and a variable (the source). It is not in any way unbelievable to be the source, hence why I posted the link above.

Here is more directed towards your deck specifically. This is a notorious problem with Pioneer decks.

pioneer pico fuse avic - Google Search

pioneer pico fuse avic - Google Search

Carbon_z · 12-10-2010, 01:11 PM

i dont like you links lol.... it scares me. The fuse isnt blow out or anything.

6spdcoupe · 12-10-2010, 01:24 PM

Quote:

Originally Posted by billet370

i dont like you links lol.... it scares me. The fuse isnt blow out or anything.

lol, don't shoot the messenger !

The fuse is not a traditional type, nor one that you can physically see without completely tearing open the unit. If blown, everything will still work, just with a bunch of unwanted noise.

Carbon_z · 12-10-2010, 01:30 PM

mmmm Ill need to check it out. Do you know where i can pick one up at? Assuming their cheap so Ill just buy a new one and swap it out. What size do i need?

6spdcoupe · 12-10-2010, 01:35 PM

Quote:

Originally Posted by billet370

mmmm Ill need to check it out. Do you know where i can pick one up at? Assuming their cheap so Ill just buy a new one and swap it out. What size do i need?

You may rethink the ease of doing this once you view it's size and availability. Viewing avic411 as well as the google results I provided will show you more in depth what is involved. Aside from the atrocious attempts that some make to remedy this by dropping a glob of solder over it.

Do you by chance (hopefully) by this unit authorized and with some sort of warranty ?

12-09-2010, 07:13 PM	#1 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	Engine Noise through Speakers Well I did a bunch of searches and assuming i have to ground my RCA's but want to verify. The first Head unit I had was a Sony xav70bt. It didnt produced any engine noise. The ground wire, amp, speakers etc are all still in the same place. The new replacement headunit is a Pioneer Avic-x920bt. Only difference setup wise is that a bypass was done on the harness of the new unit for dvd and nav usage. Once the unit is turned on, the pioneer produces alot of engine noise through the speakers. The second the unit is powered up the noise is NON STOP. If I turn the car ON but without cranking it, the noise only appears when the car is in gear but if in neutral the engine sound does not come through the speakers "WEIRD". . When car is cranked on or turned over, engine sound comes through speakers whether in gear or neutral, unlike the on position did in my previous sentence. I ran the power wire down the passenger side, amp is located behind the passenger seat. Ground wire is bolted on one of the passengar seats bolts. I have a 3 channel amp and have tried replacing the RCA's with another pair and the same sound occurs. I figured replacing the RCA would fix it but i tested the NEW RCA's without tucking them in, just loose away from everything but the sound was still there Any help would be great. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz. Last edited by Carbon_z; 12-09-2010 at 08:35 PM.

12-09-2010, 07:23 PM	#2 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	also just realized I cant wrap wire around the rca's since the units rca are part of a harness. Guess the wire wrap is for older units. ** is annoying as hell __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at** http://www.instagram.com/carbonz.

12-09-2010, 09:50 PM	#5 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	Haven't checked with meter yet... The bypass was moving a mute wire to a pin to the left so I can't check it since the bypass was only that. All the grounds on the back of the headunit are connected together since it's just ground. I might run it by the audio shop tomorrow but it's pissing me off .. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

12-10-2010, 01:38 AM	#6 (permalink)
6spdcoupe Base Member Join Date: Nov 2010 Location: Central Jersey Posts: 34 Drives: '08 TBSS, '06 E55 Rep Power: 15	Most likely your culprit .. pioneer pico fuse avic - Google Search This is a primary reason why we do not support or sell Pioneer. __________________ '06 E55, '08 TBSS, '09 CX-7 H900/TRU SSLD6i/TRU Billets/ Dyn 182s~Esotar 110s~430s~1200

12-10-2010, 11:47 AM	#7 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	also in addition, tried the LOOP for the rca's and some of the noise went away but still existed. If it was the headunit, wouldnt the loop have caught the noise??? I tried it behind the unit and on the amp. Same result. Could the speaker wires be causing this or the ground???? the speaker wires are 16 gauge and i have sr 60 Boston acoustics. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

12-09-2010, 08:08 PM	#3 (permalink)
FERRARI Enthusiast Member Join Date: Jan 2009 Location: Chattanooga, Tennessee Posts: 324 Drives: PERFECTION Rep Power: 493	Have you used a ohmmeter to check the continuity of your wiring and your ground?

12-09-2010, 09:42 PM	#4 (permalink)
90 ST A True Z Fanatic Join Date: May 2010 Location: Calgary Posts: 1,861 Drives: 90 and 15 GMC Sierra Rep Power: 422	Double check your ground, also check to see what the resistance is between the ground set screw on the amp and the battery post, if it's too high it could just be a bad ground. Also try hooking up the deck without the bypass just to make sure it's not the by pass ground causing it. If you didn't have to ground your RCA's before you shouldn't have to now.

12-10-2010, 12:01 PM	#8 (permalink)
90 ST A True Z Fanatic Join Date: May 2010 Location: Calgary Posts: 1,861 Drives: 90 and 15 GMC Sierra Rep Power: 422	unlikely the speaker wires, but yes the ground to the amp could, as i mentioned earlier.

12-10-2010, 12:21 PM	#9 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	my ground is currently under one of the passenger seats bolts that bolt to the frame of the car. Figured that was a good enough good but didnt script metal. Also the ground on the headunit is on one of the 4 bolts to the shift plate on the frame __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

12-10-2010, 12:24 PM	#10 (permalink)
90 ST A True Z Fanatic Join Date: May 2010 Location: Calgary Posts: 1,861 Drives: 90 and 15 GMC Sierra Rep Power: 422	sand the paint of the amp ground and make sure you have set the gains accordingly

12-10-2010, 12:38 PM	#11 (permalink)
6spdcoupe Base Member Join Date: Nov 2010 Location: Central Jersey Posts: 34 Drives: '08 TBSS, '06 E55 Rep Power: 15	I absolutely agree with the sanding down the ground plane, however I believe with 99% certainty that this is not your problem. Had this been a fresh install and nothing prior was in the car, then sure, it could be one of many possibilities. However you mentioned you had a Sony deck prior and no issues. You now have a control (your vehicle and equipment inside) and a variable (the source). It is not in any way unbelievable to be the source, hence why I posted the link above. Here is more directed towards your deck specifically. This is a notorious problem with Pioneer decks. pioneer pico fuse avic - Google Search pioneer pico fuse avic - Google Search __________________ '06 E55, '08 TBSS, '09 CX-7 H900/TRU SSLD6i/TRU Billets/ Dyn 182s~Esotar 110s~430s~1200

12-10-2010, 01:11 PM	#12 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	i dont like you links lol.... it scares me. The fuse isnt blow out or anything. __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

12-10-2010, 01:30 PM	#14 (permalink)
Carbon_z A True Z Fanatic Join Date: Sep 2009 Location: Atlanta, GA Posts: 1,694 Drives: Carbon Fiber 370z Rep Power: 19	mmmm Ill need to check it out. Do you know where i can pick one up at? Assuming their cheap so Ill just buy a new one and swap it out. What size do i need? __________________ Full Carbon Fiber Nissan 370z "400zTT" Fully Built 4.0L Twin Turbo 1300hp, 1100whp. Follow me on Instagram at http://www.instagram.com/carbonz.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Engine Noise post-Oil Cooler Install	spearfish25	Engine & Drivetrain	65	04-09-2015 12:59 PM
Pic request: 370z engine bay w/stillen g3's and Seibon engine cover.	atx370z	Nissan 370Z Photos / Spyshots / Video / Media Gallery	20	01-05-2011 12:50 PM
Tsb: 2007-2009 nissan z; tapping noise from dash area when engine is running	AK370Z	370Z Technical Service Bulletins (TSB) / Recalls	0	02-08-2010 09:59 PM
Engine Noise :(	The Weapon	Audio & Video	57	11-04-2009 08:17 PM