Spacers

tbss370z · 07-21-2009, 09:02 PM

I had front spacers installed today by the dealer. In order to install them, the calipers need to be removed in order to install the new studs. The dealer charged me over $300. Then I was told that the spacers needed to be removed in order to past the annual state inspection. Did I get overcharged by the dealer and is it worth it?

FuszNissan · 07-21-2009, 09:08 PM

Whats their labor rate?

tonmed123 · 07-21-2009, 09:14 PM

Quote:

Originally Posted by tbss370z

I had front spacers installed today by the dealer. In order to install them, the calipers need to be removed in order to install the new studs. The dealer charged me over $300. Then I was told that the spacers needed to be removed in order to past the annual state inspection. Did I get overcharged by the dealer and is it worth it?

Modshack DIY: Front Stud replacement/ Spacer install

Why removed to pass inspection?

tbss370z · 07-21-2009, 09:21 PM

I can't tell from the bill. I'll have to call and find out. Is it true spacers are for off road use only?

tbss370z · 07-21-2009, 09:24 PM

The dealer said that the spacers will not pass inspection in PA. I know I can probably take it somewhere else and hope they don't notice the spacers!

LiquidZ · 07-21-2009, 11:00 PM

Spacers not passing inspections is definitely strange.

As far as I know, the wheel cannot extend pass the fender. As long as you don't do this, you should be fine.

Zerafian · 07-21-2009, 11:38 PM

So it took the dealership over 2 hours to install those...DAMN!

They only have the version where you have to place extended studs in??...I figure there are spacers out there you that have studextension already on them...just like every other spacer out there. *Shrugs*

According to this post below the bolt patterns are the same as the 350z...you and every other 370z owner can get spacers just like the pic below up to 30mm if thats the case :/...Only takes about 10 minutes a tire to install if you have a torque wrench. I suppose the only question is, will they fit the hub and if so are there hubcentric rings to fit in :dunno:

FAQ: Please read this before asking a 370Z related question

like this

OMGWTFBBQ · 07-22-2009, 01:46 AM

Actually, I don't think you can use those. From what I've read regarding spacers on the 370z, the only ones that will work are the ones where you need to replace the stock studs with extended studs. The spacers with the built-in studs WILL NOT work.

tbss370z · 07-22-2009, 06:09 AM

I did use the Ichiba 20MM version II spacers that you use on the existing studs for the rears. But I believe I read that you need to install version I with the new studs for the front.

Modshack · 07-22-2009, 10:59 AM

Quote:

Originally Posted by tbss370z

I did use the Ichiba 20MM version II spacers that you use on the existing studs for the rears. But I believe I read that you need to install version I with the new studs for the front.

That is correct. The machining on the front wheel is different and does not have a deep enough or large enough recess to clear the original studs. Keep in mind you will also have to remove these (Type 2) to use the spare..

Rear wheel:

Mike · 07-22-2009, 12:45 PM

yeah, and I found out I can't use the type 2 on the rears with the Nismo wheels either, as the studs still contact the wheel when installed. I'm having difficulty banging out the new longer front studs,so I am going to try a 25 mm spacer in back instead, as that should fully cover the oem studs when installed.

Mike · 07-22-2009, 12:47 PM

Quote:

Originally Posted by Zerafian

I suppose the only question is, will they fit the hub and if so are there hubcentric rings to fit in :dunno:

FAQ: Please read this before asking a 370Z related question

like this

They are hubcentric to both the wheel and the hub.

DuReichstSoGu · 07-22-2009, 12:48 PM

ugh spacers are FAIL!

Phimosis · 07-26-2009, 05:00 PM

Quote:

Originally Posted by DuReichstSoGu

ugh spacers are FAIL!

Why are they a fail? They increase the track width. They are attached by machine pressed bolts. If you go with a wheel that has higher offset to bring the tires out to the lip, you're just essentially adding an aluminum spacer to do it, just that it's attached to the wheel rather than the hub. And, they significantly improve the looks of the 370z. I showed up with Ichiba spacers in hand and Big Brand Tires charged me $120 to install both front and rears.

ZKindaGuy · 07-27-2009, 11:00 AM

Quote:

Originally Posted by Zerafian

.....I suppose the only question is, will they fit the hub and if so are there hubcentric rings to fit in :dunno:

can someone please explain from a spacer standpoint, what exactly must the spacer look like physically in order to be considered "hub-centric"? What would a non-hub-centric spacer look like?

07-21-2009, 09:02 PM	#1 (permalink)
tbss370z Base Member Join Date: May 2009 Location: King of Prussia, PA Posts: 40 Drives: 09 Nissan GP 370Z M6 Rep Power: 15	Spacers I had front spacers installed today by the dealer. In order to install them, the calipers need to be removed in order to install the new studs. The dealer charged me over $300. Then I was told that the spacers needed to be removed in order to past the annual state inspection. Did I get overcharged by the dealer and is it worth it? __________________ 09 Nissan 370Z Base + Sport/Ichiban spacers/Takeda Intake with heat shields/HKS Exhaust/ 88 Porsche 944T, 06 Trailblazer SS/

07-21-2009, 09:08 PM	#2 (permalink)
FuszNissan A True Z Fanatic Join Date: May 2009 Location: St. Louis Posts: 14,275 Drives: Pure Sex Rep Power: 541	Whats their labor rate? __________________ Mods: Too Many to list! LouFuszNissan ZDAYZ 2012

07-21-2009, 09:21 PM	#4 (permalink)
tbss370z Base Member Join Date: May 2009 Location: King of Prussia, PA Posts: 40 Drives: 09 Nissan GP 370Z M6 Rep Power: 15	I can't tell from the bill. I'll have to call and find out. Is it true spacers are for off road use only? __________________ 09 Nissan 370Z Base + Sport/Ichiban spacers/Takeda Intake with heat shields/HKS Exhaust/ 88 Porsche 944T, 06 Trailblazer SS/

07-21-2009, 09:24 PM	#5 (permalink)
tbss370z Base Member Join Date: May 2009 Location: King of Prussia, PA Posts: 40 Drives: 09 Nissan GP 370Z M6 Rep Power: 15	The dealer said that the spacers will not pass inspection in PA. I know I can probably take it somewhere else and hope they don't notice the spacers! __________________ 09 Nissan 370Z Base + Sport/Ichiban spacers/Takeda Intake with heat shields/HKS Exhaust/ 88 Porsche 944T, 06 Trailblazer SS/

07-21-2009, 11:00 PM	#6 (permalink)
LiquidZ A True Z Fanatic Join Date: Nov 2008 Location: Columbus, OH Posts: 1,940 Drives: Mag. Black 2009 370Z Rep Power: 704	Spacers not passing inspections is definitely strange. As far as I know, the wheel cannot extend pass the fender. As long as you don't do this, you should be fine. __________________

07-21-2009, 11:38 PM	#7 (permalink)
Zerafian A True Z Fanatic Join Date: Jan 2009 Location: Chattanooga, TN Posts: 1,334 Drives: 13' MB 370z Rep Power: 24238	So it took the dealership over 2 hours to install those...DAMN! They only have the version where you have to place extended studs in??...I figure there are spacers out there you that have studextension already on them...just like every other spacer out there. Shrugs According to this post below the bolt patterns are the same as the 350z...you and every other 370z owner can get spacers just like the pic below up to 30mm if thats the case :/...Only takes about 10 minutes a tire to install if you have a torque wrench. I suppose the only question is, will they fit the hub and if so are there hubcentric rings to fit in :dunno: FAQ: Please read this before asking a 370Z related question like this __________________ LC500 exhaust set uphttps://www.youtube.com/watch?v=bI7DiA43ZYw&t Last edited by Zerafian; 07-22-2009 at 10:18 AM.

07-22-2009, 01:46 AM	#8 (permalink)
OMGWTFBBQ A True Z Fanatic Join Date: Jan 2009 Location: the OC Posts: 1,886 Drives: 08 SGM IS350 Rep Power: 4549	Actually, I don't think you can use those. From what I've read regarding spacers on the 370z, the only ones that will work are the ones where you need to replace the stock studs with extended studs. The spacers with the built-in studs WILL NOT work. __________________ Zele Performance \| Varis \| Powerhouse Amuse \| Craftsquare \| Tommy Kaira \| Top Secret \| HKS \| Defi \| Volk Racing \| Cusco \| SPL \| Never ending build thread.. PM me if you have rare JDM parts for sale!

07-22-2009, 06:09 AM	#9 (permalink)
tbss370z Base Member Join Date: May 2009 Location: King of Prussia, PA Posts: 40 Drives: 09 Nissan GP 370Z M6 Rep Power: 15	I did use the Ichiba 20MM version II spacers that you use on the existing studs for the rears. But I believe I read that you need to install version I with the new studs for the front. __________________ 09 Nissan 370Z Base + Sport/Ichiban spacers/Takeda Intake with heat shields/HKS Exhaust/ 88 Porsche 944T, 06 Trailblazer SS/

07-22-2009, 12:45 PM	#11 (permalink)
Mike The370Z.com Sponsor Join Date: Jun 2009 Location: Loganville, GA Posts: 5,944 Drives: 370z Rep Power: 2185	yeah, and I found out I can't use the type 2 on the rears with the Nismo wheels either, as the studs still contact the wheel when installed. I'm having difficulty banging out the new longer front studs,so I am going to try a 25 mm spacer in back instead, as that should fully cover the oem studs when installed. __________________ NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z Porsche: 93 968 / 23 Macan GTS / 93 968

07-22-2009, 12:48 PM	#13 (permalink)
DuReichstSoGu Base Member Join Date: Jul 2009 Location: socal Posts: 25 Drives: 370z Rep Power: 15	ugh spacers are FAIL!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Spacers	tbss370z	Brakes & Suspension	20	03-17-2014 05:58 AM
Speaker Spacers	Mike@ZE	ZEnclosures	22	01-28-2012 07:03 PM
Eibach spacers	FricFrac	Brakes & Suspension	0	06-14-2009 06:18 AM
camber kit and spacers questions	DJcuetip	Wheels & Tires	7	05-25-2009 09:42 AM
Spacers on stock Z?	ArtVandaleigh	Wheels & Tires	67	04-13-2009 10:44 AM