Another update: the injectors are FIC1100's.

Checked my bank account... lol holding off on the ID1300's until later. Right now we will go for parity and we will crank up the fuel pressure probably to 58psi which is good for atleast 925whp on 93 oct. I will know more tomorrow morning.

Mike

So we are calling it for the moment. I ran out of fuel... Smfh!!! Out of pump and out of injectors in the 8xx's. But no worries I am going to be swapping my fuel pump out and my injectors after zdayz. We are hoping to see well into the 1xxxrwhp on the new pump and injectors. Today was full of a bunch of small technical issues that once fixed actually dropped our power output! *mindblown!* today was mainly to get it up and running I will follow up when we get these issues fixed. I will say there are a LOT of advantages to the ecutek software! We now have launch control, 2step, flat foot shifting (we are foregoing due to the power levels) and a real traction control. So stay tuned. I will post up a dyno chart here soon. We were at 854rwhp on 24psi @7100rpms and 682ftlbs @6200rpms when we called it. 1 more hp and 8ftlbs of tq for my new base map compared to my old tuned map. So all in all we made more power on a lower reading dyno and gained fine tuning capabilities, features and tons of room to grow.

The more I get to see how ecutek works on the back end the more I am falling in love with it! Did I mention a true traction control! And 8 levels to set it to!!!

Glad to here things are going farely well and your excited with what you see so far. I'm loony forward to seeing a 1000 hp dyno sheet!

Just wanted to let everyone know that EcuTek has now* released all their new Phase 2 features - Anyone that has been recently tuned by me already has them - now all tuners will have access to it!

Thanks, John! Grabbed the update and am programming my ECU as I type this. Will have data logs for maps 3 and 4 shortly!


Sent from my iPhone using Tapatalk

Hey John, does this update include traction control adjustment? What's new?

I found this INFO
Nissan 370Z RaceROM Phase 2

ProECU Updates:
Fully defined Variable Timing Control (VTC)
Set the VTC angle at idle, overrun and on full load
Fully defined Variable Valve Event Lift (VVEL)
Set the VVEL angle at idle, overrun and on full load
Knock control per cylinder
Log and adjust the knock limit for each cylinder
Throttle and torque control
Torque limits and full pedal to throttle control
Detailed Fuel Injector control
Injector size, lag time and firing angle
Overrun fuel cut
Control when the fuel injectors restore
MAF Sensor rescaling
Rescale for new intakes without upsetting the engine load
Cruise control
Adjust the maximum target and set speeds
Radiator fan control
Adjust the fan duty cycle
Gear Ratios
Correct for new gears or final drives
New RaceROM Features:
Map Switching
Rev counter indication of the four different map switch modes
Flat Foot Shift
Full throttle gear changes (Manual Transmission models only)
Speed Density
MAP sensor based tuning with VVEL compensation
RaceROM Controller
Use the cruise control switch gear for adjusting calibration
Knock Warning
Check engine light flashes when knocking is detected
Per Gear Rev Limit
A different rev limit in each gear
Custom Maps
Create a map to do almost anything!
Launch Control
Adjustable Launch RPM using the cruise control (Manual Transmission models only)
Traction Control
Adjustable traction control using custom maps
Boost Control
Closed loop boost control using custom maps
Flex-Fuel
Ethanol flex-fuel tuning using custom maps
AFR Control
Closed loop target AFR control using custom maps
Fail-Safe
Protect the engine from any dangerous situations
Gauge Hijack
Display lambda, AFR, fuel trims or ethanol content on the oil temp gauge

So in that list it has gear ratio and rear end ratio. Is that only for auto or can it fix srm when rear end is changed?

[QUOTE=lj909;3206262]So in that list it has gear ratio and rear end ratio. Is that only for auto or can it fix srm when rear end is changed?[/QUOTE

It's in the software.. been in there for 2 years

John

Ok so know that I finally bought this lol does the " full pedal to throttle control" mean that when I mash the pedal to the floor the TBs actuall open 100% ;) and not like 90

Who tunes in florida?

Any tuners in jersey

whoops.

BIllet Design Motorsport Marco is extremely knowledgeable

depending on where in NJ you are making the drive to Real Auto Dynamics in Long Island might be worth your while. Alex and the crew there have it well put together.

Does any body tune near Toronto Canada

Best tune around Wilmington North Carolina?

We are about 5 hours away from you :)

Jebus! lol thats a long drive. BUT with good results im seeing and it being worth it. Id 100% make the drive