Nissan 370Z Forum  

370Z Forums HOME My Picture Album Nissan 370Z Pictures Premium Membership Become a Forum Sponsor
Go Back   Nissan 370Z Forum > Search Forums
Reload this Page Search Results
Register All Albums FAQDonate Members List Calendar Today's Posts


Showing results 1 to 8 of 8
Search took 0.00 seconds. Search: Posts Made By: kenchan
Forum: DIY Section (Do-It-Yourself) 09-24-2015, 03:00 PM
Replies: 68
Views: 44,316
Posted By kenchan
carlitos if i was to do it again i would just...

carlitos if i was to do it again i would just install the front stillen bar. similar torsion rate as the whitelines but has the collars welded just like the factory bar. :D

as for the rear.. i'd...
Forum: DIY Section (Do-It-Yourself) 01-03-2015, 07:46 PM
Replies: 68
Views: 44,316
Posted By kenchan
Yah, on my 09 I'm just running the front...

Yah, on my 09 I'm just running the front whitelines. Stock rear bar.
Forum: DIY Section (Do-It-Yourself) 10-31-2014, 11:29 AM
Replies: 68
Views: 44,316
Posted By kenchan
oh...just take it easy for a while when you drive...

oh...just take it easy for a while when you drive cause the car will respond differently.. honestly the rear bar is fine on this car, just the front needs a tad bit of stiffening.

btw my car is...
Forum: DIY Section (Do-It-Yourself) 10-31-2014, 11:22 AM
Replies: 68
Views: 44,316
Posted By kenchan
:icon18: :tup: thanks for playing. and...

:icon18: :tup: thanks for playing.

and yah, leave the rear stock for now. the front only in mid- setting should make the car feel real good.
Forum: DIY Section (Do-It-Yourself) 10-31-2014, 10:40 AM
Replies: 68
Views: 44,316
Posted By kenchan
you installed it backwards. :shakes head:

you installed it backwards. :shakes head:
Forum: DIY Section (Do-It-Yourself) 07-30-2014, 10:46 AM
Replies: 68
Views: 44,316
Posted By kenchan
oh i didnt see this post until just now... :ugh: ...

oh i didnt see this post until just now... :ugh:

i used my milwaukee 18v 3/8 drive impact.

i also have a corded 1/2 drive heavy duty impact as well if my 3/8 drive
can't handle it, but for...
Forum: DIY Section (Do-It-Yourself) 04-17-2014, 06:52 PM
Replies: 68
Views: 44,316
Posted By kenchan
my 18v impact took it off in about 5sec. :p

my 18v impact took it off in about 5sec. :p
Forum: DIY Section (Do-It-Yourself) 08-15-2013, 02:39 PM
Replies: 68
Views: 44,316
Posted By kenchan
i did my whiteline (front only) looking at...

i did my whiteline (front only) looking at chris's DIY. :) reps given.

btw, i just used my combi wrench to hold endlink bolt, 18v impact gun, and a torque wrench to do the work. nice and quick.
Showing results 1 to 8 of 8

 
Forum Jump

All times are GMT -5. The time now is 01:12 AM.

Contact Us - Home Page - Archive - Top

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2