Template for Nismo Wing/Spoiler

mattanthony23 · 05-30-2017, 05:47 PM

I am installing an OEM 2010 Nismo spoiler on my 2015 base model. Since this is a new spoiler going on a spoilerless car, I wanted to have the template to drill the holes properly.

If anyone has this template please respond or private message me. Thank you!

TreeSemdyZee · 05-30-2017, 10:09 PM

When I installed a spoiler on my 350, I taped clear plastic tight to the wing. Circled the mount holes.
Took the plastic off and placed on my car.
When I first put the wing in place, I thought I had majorly screwed up, but once I tightened it down, it fit perfectly.

cooltoy · 05-30-2017, 11:06 PM

Zip ties work well.

Quote:

Originally Posted by axmea?

Try this:
Use the transfer technique. Use small zip ties. Secure the zip tie to the spoiler's mounting hole using a small amount of masking tape where tab end lands at the center of the hole. Repeat this process to the holes you want to use to bolt the spoiler. 4 is enough. Set your spoiler on the hatch checking for eveness and if centered. Better to have help holding the spoiler down. Transfer the zip ties onto the hatch by firmly holding the tie and taping it onto the hatch. Lift your spoiler off slowly. Get a sharpie to mark where the tab lands and that's your drill mark for your spoiler holes. .

Quote:

Originally Posted by OldGuyFla

Also a little different approach to the zip tie method might be - center the zip tie on the spoiler holes you wish to use (the tie half & half on each side of the hole) tape it fast. Then take a very small drill bit & drill a hole in the zip tie at the center of the hole. Then when removing the spoiler you can just drill through that small hole in the zip tie.

Just food for thought!

05-30-2017, 05:47 PM	#1 (permalink)
mattanthony23 Base Member Join Date: Mar 2015 Location: San Diego, CA Posts: 77 Drives: 2015 370Z 7AT Base Rep Power: 10	Template for Nismo Wing/Spoiler I am installing an OEM 2010 Nismo spoiler on my 2015 base model. Since this is a new spoiler going on a spoilerless car, I wanted to have the template to drill the holes properly. If anyone has this template please respond or private message me. Thank you!

05-30-2017, 10:09 PM	#2 (permalink)
TreeSemdyZee Premium Member Join Date: Dec 2009 Location: Kentuck-IANA Age: 59 Posts: 4,877 Drives: '09 370 & ‘14 Juke Rep Power: 27408	When I installed a spoiler on my 350, I taped clear plastic tight to the wing. Circled the mount holes. Took the plastic off and placed on my car. When I first put the wing in place, I thought I had majorly screwed up, but once I tightened it down, it fit perfectly. mattanthony23 likes this. __________________ Borla S-Type \| Motordyne \| Z1 (lots) \| South Bend \| K&N \| Nismo/Nismo S-Tune \| Eibach \| Aerojacket \| Fujimara \| Spl \| ZSpeed Performance \| Kenwood-Infinity-Sound Ordnance \| Whiteline \| Ecutek \| Hotchkis \| Clazzio \| VQ Vortex \|Morimoto XB \|Dynosty Tune 329.64hp 265.73 ft/lb

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
OEM Sport Spoiler Template	Jjaden	Exterior & Interior	0	02-18-2012 07:31 AM
[WTB] WTB: S-Tune Rear Spoiler 'Template'	mwz516	Parts for sale (Private Classifieds)	3	11-11-2011 12:36 PM
WTB: S-Tune Rear Spoiler 'Template'	mwz516	Wanted	1	11-11-2011 12:11 PM
Sport spoiler template	v8zracer260z	Boardwalk Nissan - Supporting Dealer	5	11-14-2010 05:07 PM
OEM rear spoiler template	super_fla	DIY Section (Do-It-Yourself)	2	08-19-2010 02:54 PM