Nismo Rear and stock spoiler????

Funky370z · 02-20-2010, 05:54 PM

Quote:

Originally Posted by jmlenz

Nice looking Z!

Couple questions for you...does the rear bumper fit without any other hardware? As in no new fender liners, bumper reinforcements, etc. Just pull of factory bumper and bolt on Nismo?

The front bumper from what Ive read requires the nismo diffuser/under spolier to fit the factory undertray and new fender liners since it is wider. Did you use these parts?

The rear bumper will bolt on, What I did was hack up some old fender liners and made pieces to extend the non nismo liners. I did this front and back.

For the front bumper I did buy the Chin piece so that my belly pan would bolt to the bumper. I just had to drill two new holes and everything lined up nicely.

If you want a true OEM look your gonna want to purchase the liners, I might even in the future do so.

jmlenz · 02-20-2010, 06:45 PM

^ good info Funky. Glad to hear the rear bolts on without issues, less the fender liners. Do you know the part numbers for the rear Nismo liners? I can find the part numbers for the front Nismo liners, just not the rear so I wasnt sure it needed them...but looks like it does. The front liners are about $93/each for the Nismo.

cullmann · 05-06-2010, 01:48 AM

Quote:

Originally Posted by jmlenz

^ good info Funky. Glad to hear the rear bolts on without issues, less the fender liners. Do you know the part numbers for the rear Nismo liners? I can find the part numbers for the front Nismo liners, just not the rear so I wasnt sure it needed them...but looks like it does. The front liners are about $93/each for the Nismo.

Rear fender protector part number is below..

1. H5064 1A47A
2. H5065 1A47A

Can you give me the part number for the front Nismo liners ?

scruffydog · 05-06-2010, 02:10 AM

Quote:

Originally Posted by cullmann

Rear fender protector part number is below..

1. H5064 1A47A
2. H5065 1A47A

Can you give me the part number for the front Nismo liners ?

F3845-1A30A (Front inner wheel well liner for one side)
F3844-1A30A (Other side - Without these there is a gap between the sides of the fron bumper and the inner liner of the wheel wells)

Hope this helps

cullmann · 05-06-2010, 02:39 AM

Quote:

Originally Posted by scruffydog

F3845-1A30A (Front inner wheel well liner for one side)
F3844-1A30A (Other side - Without these there is a gap between the sides of the fron bumper and the inner liner of the wheel wells)

Hope this helps

Thank you for your information.
But, those parts are for the front fender liners, do you know the small parts to cover the gap between the front bumper and fender liners ?
I heard that two pieces for each fender and bracket to hold the bumper and under cover.

Chris_1 · 05-06-2010, 03:06 PM

Quote:

Originally Posted by Funky370z

The rear bumper will bolt on, What I did was hack up some old fender liners and made pieces to extend the non nismo liners. I did this front and back.

For the front bumper I did buy the Chin piece so that my belly pan would bolt to the bumper. I just had to drill two new holes and everything lined up nicely.

If you want a true OEM look your gonna want to purchase the liners, I might even in the future do so.

No offense, but your wheel offset is WAY off, I really dont think the car looks good, maybe some spacers??

tonybui · 05-07-2010, 11:17 AM

how much did the rear run you ?

celiboom · 01-02-2017, 06:35 PM

When you said you used some used liner for front and rear bumper, which liner did you used?

Do you have any close pics? Dealer wants 400$ for both (canadian $) so If I could end up fabricating them myself!

cooltoy · 01-02-2017, 11:00 PM

2010.

celiboom · 01-06-2017, 01:37 PM

It's ok, I was taking a chance!! was able to fit my nismo bumper quite easily

01-02-2017, 11:00 PM	#39 (permalink)
cooltoy Elite Member Join Date: Jun 2012 Location: Calgary Posts: 13,938 Drives: 14 PW 370Z S/T MT Rep Power: 240204	2010. NISMO IX likes this. __________________ Member of kenchan's "photoshopped mods" and "proper offsets" gang.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Nismo rear deck spoiler on 370Z sport coupe	Stevie Z	Exterior & Interior	47	06-30-2017 04:28 PM
370z rear nismo spoiler?	onefastz	Exterior & Interior	78	09-27-2013 11:27 AM
looking to buy PW rear spoiler	jookiyaya	Wanted	0	10-21-2009 07:25 AM
OEM Rear Spoiler	javol	Nissan 370Z General Discussions	5	07-25-2009 09:21 PM

02-20-2010, 06:45 PM	#32 (permalink)
jmlenz Track Member Join Date: May 2009 Location: San Diego Posts: 645 Drives: a car Rep Power: 642	^ good info Funky. Glad to hear the rear bolts on without issues, less the fender liners. Do you know the part numbers for the rear Nismo liners? I can find the part numbers for the front Nismo liners, just not the rear so I wasnt sure it needed them...but looks like it does. The front liners are about $93/each for the Nismo.

05-07-2010, 11:17 AM	#37 (permalink)
tonybui A True Z Fanatic Join Date: May 2009 Location: Maryland Posts: 1,397 Drives: 09 Sports 6 Speed Rep Power: 426	how much did the rear run you ?

01-02-2017, 06:35 PM	#38 (permalink)
celiboom Base Member Join Date: Jul 2015 Location: canada Posts: 115 Drives: 370z 2016 Rep Power: 204	When you said you used some used liner for front and rear bumper, which liner did you used? Do you have any close pics? Dealer wants 400$ for both (canadian $) so If I could end up fabricating them myself!

01-06-2017, 01:37 PM	#40 (permalink)
celiboom Base Member Join Date: Jul 2015 Location: canada Posts: 115 Drives: 370z 2016 Rep Power: 204	It's ok, I was taking a chance!! was able to fit my nismo bumper quite easily