Nissan 370Z Forum
Page 2 of 4 1 2 34
Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)
-   Nissan 370Z General Discussions (http://www.the370z.com/nissan-370z-general-discussions/)
-   -   20mm vs 25mm spacers (http://www.the370z.com/nissan-370z-general-discussions/89632-20mm-vs-25mm-spacers.html)

MagmaREDZilla 05-04-2014 12:50 PM
Quote:
Originally Posted by equalme (Post 2806305)
20/25 on swifts here. Was on stock rays but Michelin pss tires which runs a little wider than the potenza. Perfect aggressive stance
Ok I'm pretty much sold on 20/25 but do you think you might have had any issue if you were .5" more lower than swifts?


Sent from my LG-D801 using Tapatalk

cruzthepug 05-04-2014 02:32 PM
This may be a stupid question, but if you just install bolt on spacers at stock height (no spring change), would that require an alignment?

b15 05-04-2014 02:42 PM
Quote:
Originally Posted by MagmaREDZilla (Post 2806359)
Ok I'm pretty much sold on 20/25 but do you think you might have had any issue if you were .5" more lower than swifts?


Sent from my LG-D801 using Tapatalk
Yes I'm pretty sure 25mm rear will rub unless you dial in negative camber to tuck the top of the wheel. I run 20mm bolt ons all around on Swifts with no issues.

Quote:
Originally Posted by cruzthepug (Post 2806422)
This may be a stupid question, but if you just install bolt on spacers at stock height (no spring change), would that require an alignment?
No.

MagmaREDZilla 05-04-2014 02:58 PM
Quote:
Originally Posted by b15 (Post 2806432)
Yes I'm pretty sure 25mm rear will rub unless you dial in negative camber to tuck the top of the wheel. I run 20mm bolt ons all around on Swifts with no issues.


No.
Thanks for your input b15, I do have rear camber kit but I would like to stay in factory spec as much as I can due to tire wear. Which bolt on did you go up with up front?

Sent from my LG-D801 using Tapatalk

MagmaREDZilla 05-04-2014 03:00 PM
Could anybody with a lower drop or coilovers confirm that 25mm in rear will rub?

Sent from my LG-D801 using Tapatalk

b15 05-04-2014 03:01 PM
Quote:
Originally Posted by MagmaREDZilla (Post 2806440)
Thanks for your input b15, I do have rear camber kit but I would like to stay in factory spec as much as I can due to tire wear. Which bolt on did you go up with up front?

Sent from my LG-D801 using Tapatalk
If you want factory camber specs with your drop, I'm almost certain you'll rub in the rear with 25mm

I have Z1 bolt ons f/r

MagmaREDZilla 05-04-2014 03:07 PM
Quote:
Originally Posted by b15 (Post 2806444)
If you want factory camber specs with your drop, I'm almost certain you'll rub in the rear with 25mm

I have Z1 bolt ons f/r
Then I might just go with 20mm all around b15, how do you like them Z1's? I hear good things about their products all around.

Sent from my LG-D801 using Tapatalk

synolimit 05-04-2014 03:14 PM
Quote:
Originally Posted by MagmaREDZilla (Post 2806441)
Could anybody with a lower drop or coilovers confirm that 25mm in rear will rub?

Sent from my LG-D801 using Tapatalk
I'm 28 out from OEM and don't rub lower than swifts.

synolimit 05-04-2014 03:17 PM
Quote:
Originally Posted by Mt Tam I am (Post 2806174)
You do not plan on tracking this car I assume.
Curious for your reasoning behind this.

MagmaREDZilla 05-04-2014 03:19 PM
Quote:
Originally Posted by synolimit (Post 2806456)
I'm 28 out from OEM and don't rub lower than swifts.
Damnn that sounds insane synolimit! What are you dropped on and any pics of the 28mm ?:D

Sent from my LG-D801 using Tapatalk

MagmaREDZilla 05-04-2014 03:21 PM
Quote:
Originally Posted by synolimit (Post 2806458)
Curious for your reasoning behind this.
I'm guessing he assumed that due to me putting bolt-on spacers in front? I do hear that you have to keep re-torquing them every couple of hundred miles

Sent from my LG-D801 using Tapatalk

b15 05-04-2014 03:26 PM
Quote:
Originally Posted by MagmaREDZilla (Post 2806451)
Then I might just go with 20mm all around b15, how do you like them Z1's? I hear good things about their products all around.

Sent from my LG-D801 using Tapatalk
I've been happy with Z1. Ordered a few things from them and shipping is always quick. You'll need a thin wall socket for the spacers and yes, re-torque after 100miles or so just like you would re-torque your lugs.

Z-Girl 12 05-04-2014 03:51 PM
I am running 20/25 mm rear on coils...no regrets.

MagmaREDZilla 05-04-2014 03:54 PM
Quote:
Originally Posted by Z-Girl 12 (Post 2806483)
I am running 20/25 mm rear on coils...no regrets.
Z-girl approximately how much is your drop? Also are you running the stock sports? An rubbing issue? Pics would be nice also. Thank you for the input. Really trying to get 25mm's in rear.

Sent from my LG-D801 using Tapatalk

synolimit 05-04-2014 04:07 PM
Quote:
Originally Posted by MagmaREDZilla (Post 2806462)
Damnn that sounds insane synolimit! What are you dropped on and any pics of the 28mm ?:D

Sent from my LG-D801 using Tapatalk
Spl mid links with swift racing 2.5" ID, 6", 10kg linear springs lowered to 26.2" on 285/35/18's. It's over an inch from OEM. Plenty of room at only -1.5 camber.

http://i39.photobucket.com/albums/e1...ps68a3231a.jpg


All times are GMT -5. The time now is 02:44 AM.
Page 2 of 4 1 2 34
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2