![]() |
Is there a window reset? When I open the door in drops down the normal inch or so...but it doesn't go back up when the door is closed.
|
|||||||
![]() |
|
|
LinkBack | Thread Tools | Display Modes |
|
|
|
|
#1 (permalink) |
|
Base Member
Join Date: Jun 2010
Location: Omaha,NE
Posts: 230
Drives: 40th Anniversary Z
Rep Power: 16 ![]() |
Is there a window reset? When I open the door in drops down the normal inch or so...but it doesn't go back up when the door is closed.
__________________
2010 40th Anniversary 2003 Toyota Highlander Limited Nebraska Huskers Boston Red Sox |
|
|
|
|
|
#2 (permalink) | |
|
A True Z Fanatic
![]() Join Date: Apr 2010
Location: Battle Lake MN
Age: 65
Posts: 183,964
Drives: 370Z 240Z
Rep Power: 2684738 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Quote:
Help: Adjusting/aligning window (need more help than just window-reset procedure)
__________________
Koni|Swift|Michelin|Motordyne|Berk|RJM Performance|Gates|SPL|Motul|Technafit|Ate Super Blue|Hawk
Tommy Kaira|Momo|Optima|Hella|Hotchkis|Red Line|ZSpeed|Stillen|B&M|H&R |
|
|
|
|
|
|
#3 (permalink) |
|
Base Member
Join Date: Mar 2012
Location: Sonoma County, CA
Posts: 163
Drives: 2011 370Z
Rep Power: 183 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
INITIALIZATION PROCEDURE
1. Disconnect battery negative terminal or power window switch connector. Reconnect it after a minute or more. 2. Door switch is OFF (close). 3. Turn ignition switch ON. 4. Operate power window switch to fully open the window. (This operation is unnecessary if the window is already fully open.) 5. Continue pulling the power window switch AUTO-UP. Even after glass stops at the fully closed position, keep pulling the switch for 3 seconds or more. 6. Initializing procedure is completed. 7. Inspect anti-pinch function. CAUTION: When initialization is not complete, power window UP does not operate while door is open. CHECK ANTI-PINCH FUNCTION 1. Fully open the door window. 2. Place a piece of wood near the fully closed position. 3. Close door glass completely with AUTO-UP. • Check that glass lowers for approximately 150 mm (5.9 in) without pinching piece of wood and stops. • Check that glass does not rise when operating the power window main switch while lowering. CAUTION: • Never check with hands and other part of body because they may be pinched. Never get pinched. • Check that AUTO-UP operates before inspection when system initialization is performed. • Perform initial setting when auto-up operation or anti-pinch function does not operate normally. • Finish initial setting. Otherwise, next operation cannot be performed. 1. Auto-up operation 2. Anti-pinch function 3. Key cylinder switch power window function 4. Automatic window adjusting function 5. Auto-up, manual-up does not operate when door is open |
|
|
|
![]() |
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| MBC issues? | AWX Z34 | Forced Induction | 7 | 04-06-2012 10:13 PM |
| 370 z top issues | sue z | New Forum Member | 4 | 04-30-2011 07:55 PM |
| Aux-In Issues | christian370z | Audio & Video | 2 | 08-10-2010 02:36 PM |
| thinking of buying 370z, then GTM turbo's , but overheat issues,oil issues ?? | Christopher | Nissan 370Z General Discussions | 19 | 10-16-2009 03:55 PM |
| Initial Z issues that are now non-issues...... | cave vulture | Nissan 370Z General Discussions | 1 | 09-06-2009 10:19 PM |