![]() |
Interesting problem... From the FSM under P0500: The vehicle speed signal is sent to the combination meter from the “ABS actuator and electric unit (control unit)” via the CAN communication
|
|||||||
![]() |
|
|
LinkBack | Thread Tools | Display Modes |
|
|
|
|
#1 (permalink) |
|
Base Member
Join Date: Jan 2016
Location: Ontario
Posts: 232
Drives: G37 Sport
Rep Power: 6722 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Interesting problem...
From the FSM under P0500: The vehicle speed signal is sent to the combination meter from the “ABS actuator and electric unit (control unit)” via the CAN communication line. The combination meter then sends a signal to the ECM via the CAN communication line. Soooo... the ABS module sends the wheel speed to the gauge cluster (via CAN bus) and it converts it to vehicle speed. The vehicle speed is then sent to the ECU. It is possible the US cluster sends the vehicle speed in MPH to the ECU. Since the ECU is expecting KPH, it throws off the calculations and s-mode doesn't work. ^^^ just my 2¢ |
|
|
|
|
|
#2 (permalink) | |
|
Track Member
Join Date: Jan 2017
Location: Vancouver, BC
Posts: 821
Drives: 17' 370Z Nismo
Rep Power: 40657 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Quote:
That definitely could be the issue, but if such a signal is critical to function of ECM, you would think a Fault or failure would be shown as other systems are looking for a "specific" speed signal. Not sure if this car (cluster) is smart enough for that. Either way, I'm not 100% sure. P.S. I Just looked into FSM a little deeper. In the Cruise control section, vehicle speed is also sent from Combo meter to ECM for CC function. In the system description, Nissan always gives the values as KPH (MPH) which leads me to believe my original theory, that "actual" values are not of concern, only signal pulses from Wheel speed sensors converted to a mechanical/electrical value for speedometer. From FSM: "BASIC ASCD SYSTEM Refer to Owner's Manual for ASCD operating instructions. Automatic Speed Control Device (ASCD) allows a driver to keep vehicle at predetermined constant speed without depressing accelerator pedal. Driver can set vehicle speed in advance between approximately 40 km/ h (25 MPH) and 144 km/h (89 MPH). ECM controls throttle angle of electric throttle control actuator to regulate engine speed. Last edited by ZoomZ; 08-27-2022 at 11:48 AM. |
|
|
|
|
|
|
#3 (permalink) | |
|
Base Member
![]() Join Date: Apr 2022
Location: U.S.
Posts: 61
Drives: 19 Nissan 370Z CY M6
Rep Power: 5 ![]() |
Quote:
__________________
2019 370Z Sport Manual
|
|
|
|
|
![]() |
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| RPM Cluster Help | bigmah | Exterior & Interior | 4 | 06-23-2020 09:51 AM |
| Individual TPMS readouts possible? | ufoz8mycow | Wheels & Tires | 3 | 07-23-2018 10:36 AM |
| [FOR SALE] 370z cluster | dwnchiu | Parts for sale (Private Classifieds) | 6 | 07-01-2014 12:47 PM |
| Guage cluster .........cluster f&ck!!! | Cjdiezel | Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs | 1 | 02-22-2012 01:22 PM |