![]() |
Well, I tried to install the base tune, from Specialty Z, last night and got an error. Looks like there might already be an UpRev tune on the car so
|
|||||||
![]() |
|
|
LinkBack | Thread Tools | Display Modes |
|
|
|
|
#1 (permalink) |
|
Enthusiast Member
Join Date: Jun 2011
Location: Columbia, MO
Age: 49
Posts: 460
Drives: ‘13 370Z ST 6M
Rep Power: 3429 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Well, I tried to install the base tune, from Specialty Z, last night and got an error. Looks like there might already be an UpRev tune on the car so I've reached out to a local shop that uses UpRev to see if they can flash it back to stock so I can install the ECUTek Tune. Hopefully they're able to!
__________________
Zack FI catback, HFC, and Start Button - Z1 Intake - Nismo S-Tune Spoiler - PasswordJDM V2 Shift Knob |
|
|
|
|
|
#2 (permalink) | |
|
Enthusiast Member
Join Date: Jun 2011
Location: Columbia, MO
Age: 49
Posts: 460
Drives: ‘13 370Z ST 6M
Rep Power: 3429 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Quote:
__________________
Zack FI catback, HFC, and Start Button - Z1 Intake - Nismo S-Tune Spoiler - PasswordJDM V2 Shift Knob |
|
|
|
|
|
|
#3 (permalink) |
|
Enthusiast Member
Join Date: Oct 2016
Location: Rancho Cucamonga, CA
Posts: 314
Drives: 2017 Nismo Tech 6MT
Rep Power: 3938 ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
A few months back I experienced a rotator cuff injury. Been on the mend since then. Certain movements are really painful, one of them being lifting a wheel and sliding it onto the studs. Even with light 3-piece wheels, the wheel+tire weighs 45-50 lbs. I was looking for some kind of aid to help me raise a wheel and hold it while I clocked it to line up the studs. At first I tried a floor jack but clocking the wheel was difficult. I decided to try a wheel dolly as it could perform both the lifting function and allow easy clocking of the wheel face to facilitate mounting. I couldn't be happier with the results and would recommend this to anyone in a similar situation. The dolly was about $125 and I picked up some rollerblade-type wheels for $25 because the original ones were crap. I had to build a plywood platform to add height when the car is way up on jack stands but, at lower levels, the dolly is all that is needed.
__________________
SOLD2017 370Z Nismo Tech 6MT PART OUT IN PROGRESS Work | Motordyne | Powertrix | Swift | Michelin | Takeda | Hotchkis | RJM | Voodoo13 | SPL | SPC | Z1 Motorsports | ZSpeed | Morimoto | Craft Square Last edited by k67p67; 08-26-2021 at 11:54 PM. |
|
|
|
![]() |
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| [MAZOC] Official "Off-Topic" Discussion Thread | m4a1mustang | MAZOC | 6670 | 09-06-2018 07:21 PM |
| What did you do with your Z today VI (ON TOPIC DISCUSSION ONLY) | AK370Z | Nissan 370Z General Discussions | 10007 | 06-08-2017 09:48 AM |
| The New "What did you do with your Z today" (with off topic replies) XVIV | eastwest2300 | The Lounge (Off Topic) | 10005 | 09-11-2015 08:57 AM |
| What did you do with your Z today V (ON TOPIC DISCUSSION ONLY) | AK370Z | Nissan 370Z General Discussions | 10148 | 06-19-2014 08:20 PM |
| The New "What did you do with your Z today" (with off topic replies) VIII | JARblue | The Lounge (Off Topic) | 10016 | 11-10-2013 11:21 AM |