Shift knob

Leingod · 04-04-2016, 03:57 PM

Quote:

Originally Posted by kenchan

i broke two strap wrenches before giving up (well, store clerk wasnt too happy i came back for a free replacement within an hr

) and used my oil filter wrench.

and yah, make sure to secure the shaft while turning so you dont spin the car under u...

i someone took mine off without damaging anything and never strapped down shaft.

I'll be starting my own iggylist soon

tonyl001 · 04-04-2016, 04:05 PM

Quote:

Originally Posted by fantaZ

Also Tried removing the front nissan badge to replace it with a blacked out one with two sided tape. seems like the stock one is bolted on. Is it? what about the rear badge is it stuck on with tape are bolted on? Thankz a bunch This info will save me alot of headache.

It's not bolted on. It has some kind of adhesive to it. All you need to do is use a heat gun or your girlfriend's/wife hair dryer and apply heat to the emblem. Once the emblem is heat it up good, you can use a flat head and pry out the badge. Just be careful with your paint. I would recommend using a small rag behind the flat head while taking it out. After you remove the emblem, remove all the adhesive that is still on car. Then you can install your new emblem just make sure the area is cleaned well so the new badge will stick. Everything is the same for the back.

CMadison · 04-05-2016, 12:45 PM

Quote:

Originally Posted by cooltoy

OEM shift knob removal (SEARCHED)

yeah, this is the method i used and it worked. although i did have someone help me.

JesseG805 · 04-05-2016, 01:32 PM

I made sure to protect the shift knob and used a strap wrench....leather on the knob ended up ripping and my oem knob was destroyed. Lol

Duc_Z09 · 04-05-2016, 02:28 PM

I just twisted mine right off. It took some muscle, but it went. Spend some more time at the gym you sissies!

TNHawk · 04-06-2016, 04:13 PM

For the badges use heat like tonyl001 mentioned but instead of a screwdriver I used dental floss in a sawing motion to remove the emblems. However, this was on my old Sentra Spec V.

iJDMTOY · 04-08-2016, 12:10 PM

you might need to use a strap wrench to remove the shift knob.

04-05-2016, 02:28 PM	#20 (permalink)
Duc_Z09 Track Member Join Date: Jan 2014 Location: Frederick MD Posts: 876 Drives: With the blinker on. Rep Power: 23	I just twisted mine right off. It took some muscle, but it went. Spend some more time at the gym you sissies! tonyl001 likes this. __________________ 2009 370z #206 (all mods are Home Depot) 2009 Ducati 848 (full Ohlins, Termignoni, etc) 2003 Grand Cherokee (long arms, big tires, 4.56, lockers)

04-08-2016, 12:10 PM	#22 (permalink)
iJDMTOY Base Member Join Date: May 2015 Location: Los Angeles Posts: 192 Drives: 370Z Rep Power: 9	you might need to use a strap wrench to remove the shift knob. __________________ http://ijdmtoy.com/Temp/72-002-1.jpg Phone: 626-872-1127 Email: info@iJDMTOY.com www.iJDMTOY.com

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[FOR SALE] ZELE shift knob $250+your oem shift knob	rAiN	Parts for sale (Private Classifieds)	12	08-13-2015 06:41 PM
Installed Alcantara shift boot and Nismo Ti Shift Knob	austex	Exterior & Interior	17	09-21-2014 07:15 PM
[FOR SALE] Stock Shift knob & custom CFE shift boot	edub370	Parts for sale (Private Classifieds)	4	08-21-2013 12:23 PM
Shift knob installation? Shift knob recommendations?	Gibby1113	DIY Section (Do-It-Yourself)	21	05-30-2013 07:08 PM
SOLD: 7AT Red/Carbon Shift knob with OEM 6MT Shift boot (SW Florida)	TMAN1985	Parts for sale (Private Classifieds)	8	04-23-2012 09:01 PM

04-05-2016, 01:32 PM	#19 (permalink)
JesseG805 Base Member Join Date: Feb 2015 Location: Simi Valley, California Posts: 121 Drives: 12 370z 6mt Rep Power: 10	I made sure to protect the shift knob and used a strap wrench....leather on the knob ended up ripping and my oem knob was destroyed. Lol

04-06-2016, 04:13 PM	#21 (permalink)
TNHawk Base Member Join Date: Jun 2015 Location: St. Paul, MN Posts: 2 Drives: 14 Nissan 370z Sport Rep Power: 9	For the badges use heat like tonyl001 mentioned but instead of a screwdriver I used dental floss in a sawing motion to remove the emblems. However, this was on my old Sentra Spec V.