I don't know what this means but the oil cooler will have the vented fender liner and (possibly) my drivers side brake duct tube. Will be off-center towards the wheel well.

You know what it means ;)

Finalized my install/tune quote with Moore. They want an entire week to do it just to be safe. So I'm taking off Monday, July 29th to head to Moore and "assist" with taking the car apart. I'm dragging Cliff from Daedalus Customs with me because he wants to handle removing the headlights himself - since the last time the car was worked on the body shop broke the moisture seals on both lights which caused issues. Doubt I'm going to take the entire week off but I'm asking them to take tons of pictures.

So after a bit of talking with the GTM guys, I'm going to leave my fuel pump and injectors alone for a bit and run what comes with the kit I bought. If I really feel the need to **** with it afterward, I can always come back later. Full kit contents:

-Rotrex C38 supercharger
-GTM compressor housing
-GTM Supercharger Billet aluminum brackets
-GTM billet aluminum Sc pulley
-GTM supercharger cooler kit
-Rotrex Supercharger Traction fluid
-4-Ply High Resistance Nomex Silicon couplers
-Stainless Steel T-Bolt clamps
-2.5 x 10 x 24 Bar and Plate Core Intercooler Rated @ 700hp
-Polished aluminum IC Piping
-3” MAF housing
-GTM Oil Filter Relocation Kit
-4.5” diameter Air Intake System
-Turbosmart Bypass Valve
-Pre-made steel braided oil and P.S Supply & Return lines
-All Necessary Hardware and Installation Instructions
-GTM Custom mapped plug and play engine management for optimum engine tune and power .
-GTM Basic fuel system with Bosch EV-14 650CC Injectors and - Walbro 255 Fuel Pump .
-GTM Fuel Pump Voltage Stabilizer Kit
-GTM Custom Drive belt By Bando
-GTM Heavy duty Belt idlers

I have the same injectors n pump with my kit. If I feel the need for more, the pump and injectors should be good for anyone wanting to play with E85 on a NA car, or anyone buying a tuner version of the kit.

Yeah. I'm just gonna start from there and see how it feels. I can always upgrade later.

I saw my name in your opening thread.. i was like wtf?!:bowrofl::bowrofl: Me, saying things?:roflpuke2: Man, you want a "show car." What you're doing right now, will get you to that point.:tup:

Liked Kirk's setup so I'm going with a PLX multigauge and daisy chained AFR/oil pressure/boost modules (oil pressure default).

Really love the defi sweep gauges but there's nowhere to put them except the A pillar which is a little too fast and too furious for me.

The guys at Doran recommended a really high end multigauge (forget brand) but it starts at $1200 without sensors so....


Sent from my iPhone using Tapatalk

Dash replacement options for a 6 gauge setup were just retardedly expensive so PLX it is.


Sent from my iPhone using Tapatalk

Anyone want to educated me on pulleys? I requested the 88mm pulley with my kit and was told I would need to be careful because I would be putting down over 500whp but that it wasn't dangerous to the motor or the SC.

Was told the kit normally comes with a 96mm and there is also a 92mm option as well.

Anyone know if going to the 88mm is a bad idea?

I tried to get the 88 mm pulley from Sam but he said the blower would be spinning to fast so I got the 92mm

I just talked to Sam and he said on 93 octane it wouldn't be a problem. Should I go back up to 92?

go for moarrrrr powaaaaaa lol 88mm

must
always
zone
out
cooling


fgt.

Well I don't want to do anything to endanger the motor or the blower which is why I'm asking for advice here. Anyone know?

Is 88 safe on 93 octane?